Viessmann VITOCELL-H 100 Gebrauchsanweisung



-H

H 1

Indirect-fired domestic hot water storage tank

42 and 53 USG / 160 and 200 ltr

5167 513 1.4 01/2012

Technical Data Manual

Model Nos. and pricing: see Price List



Vitocell-H 100

CHA Series

Enameled indirect-fired domestic hot ater storage tank

steel construction, ith Ceraprotect t o-coat enamel finish

Product Information

Vitocell-H 100

The horizontal tank solution for cost-efficient

domestic hot water supply. The Vitocell 100 is

a ailable in both horizontal and ertical

designs, the ertical ersion offering storage

capacities of up to 53 USG / 200 ltrs.

The benefits at a glance:

HCorrosion-protected steel tank shell with

Ceraprotect t o-coat enamel finish,

produced in-house. Magnesium anode

pro ides additional cathodic tank protection.

HHeat exchanger coil extends to the bottom

of the tank, thereby heating the entire

water content.

HExtremely convenient domestic hot ater

supply assured by fast, uniform heating

ia generously sized heat exchanger

surfaces.

HStandby losses minimized by 2¼” /

58 mm highly effecti e foamed-in-place

HCFC-free insulation.

Product Information

Cross-Section

2¼” / 58 mm highly effective Inspection port/

foamed-in-place clean-out opening

HCFC-free insulation

Non-finned, tubular heat

exchanger coil extends to tank

bottom – the entire ater

volume is heated preventing

cold spots

Tank is constructed

of steel, ith Ceraprotect

t o-coat enamel finish

Product may not be exactly as illustrated.

Technical Data

Technical data

For domestic hot ater heating applications in Suitable for heating systems with

conjunction with hot water heating boilers Hmax. DHW supply of up to 150 °F / 65.6 °C

Hmax. working pressure on the heat exchanger side of up to 150 psig /

10 bar

Hmax. working pressure on DHW side of up to 150 psig / 10 bar

Hmax. supply temperature on the heat exchanger side of up to 230 °F /

110 °C

Storage capacity USG

ltr

160

200

Recovery

with a temperature

increase of the

194°F

90°C

MBH

GPM

ltr/h

113

3.6

810

143

4.5

1032

from

50 to 113°F /

10 to 45°C

176°F

80 ºC

MBH

GPM

ltr/h

3.0

688

109

3.5

786

temperature of

......

at the supply flow rate

stated below

158°F

70 ºC

MBH

GPM

ltr/h

2.4

540

2.8

638

Recovery

with a temperature

increase of the

194°F

90°C

MBH

GPM

ltr/h

109

2.4

550

130

2.9

653

from

50 to 140°F /

10 to 60°C

176°F

80 ºC

MBH

GPM

ltr/h

1.8

412

2.2

498

temperature of

......

at the supply flow rate

stated below

158°F

70 ºC

MBH

GPM

ltr/h

1.3

292

1.4

326

Supply flo rate

for the reco ery

GPM

13.2

3.0

13.2

3.0

rates stated

Standby losses

MBH/24 h 4.8 5.1

Overall dimensions

O erall length inches

O erall width inches

O erall height inches

41½

1052

25¼

640

25¾

654

47¾

1216

25¼

640

25¾

654

Weight

Tank with insulation

lbs

227

103

256

116

Heating ater content

(heat exchanger coil)

USG

ltr

1.8

7.0

2.1

8.0

Heat exchanger surface area ft.

10.8

1.0

12.9

1.2

Connections

Heating water supply/return

∅’’ (male thread)

∅

’

(

)

temperature and pressure

∅

’

(

)

Domestic cold water ∅’’ (male thread) ¾ ¾

When planning for the recovery rate as stated or calculated, allow for the corresponding circulation pump.

The stated recovery rate is only achieved when the rated output of the boiler is equal to or greater than that stated under “Recovery”.

lease also refer to the corresponding sizing chart at the end of this manual.

Measured values are based on a room temperature of 68°F / 20 ºC and a domestic hot water temperature of 149°F / 65 ºC and can

vary by 5 %.

Technical Data

Legend

AQ Aquastat Well

BWR Boiler Water Return

BWS Boiler Water Supply

CA Consumable Anode

DCW Domestic Cold Water

DHW Domestic Hot Water

IO Inspection and Clean-out Opening

TPV Temperature and Pressure Relief Val e

O erall height

O erall width

O erall length

DCW

BWR

4¾” / 119 mm

2½” / 63 mm1½” / 37 mm

6½” / 167 mm

4¼” / 109 mm

12¼” / 311 mm

13¼” / 336 mm

18” / 459 mm

DHW and

TPV

BWS

1½” /

36 mm

Dimensions

Storage

capacity

USG

ltr

160

200

a inches

866

40½

1030

b inches

9¾

250

11¾

300

Technical Data

Pressure drop on heating ater side Pressure drop on domestic hot ater side

(primary circuit) (secondary circuit)

42 and 53 USG / 160 and 200 ltr storage capacity

Waterflow

ltr/h

GPM

400 1000

“ w.c.

mbar

44 10 000

16 40

20 50

24 60

32 80

40 100

80 200

120 300

160 400

200 500

240 600

320 800

1.6 4

2 5

2.4 6

3.2 8

4 10

8 20

12 30

1.2 3

2.2 500

2.6 600

3.5 800

4.4 1 000

9 2 000

13 3 000

18 4 000

22 5 000

26 6 000

35 8 000

Pressure drop

Waterflow

ltr/min

40 100

“ w.c.

mbar

1.2 3

1.6 4

2 5

2.4 6

3.2 8

4 10

8 20

12 30

16 40

20 50

24 60

32 80

167

133

100

Product Installation

Standard Equipment

Steel domestic hot water storage tank with

two-coat enamel finish, mounted

polyurethane foam insulation and

electrostatically powder coated sheet metal

enclosure panel in a itosil er finish with...

– preinstalled consumable anode

– integrated thermometer and

– adjustable le eling feet.

The following are packed separately and

attached to the crate:

– installation fittings package: with the

necessary brass couplings, adaptors, other

necessary hardware, and hemp

– temperature and pressure relief al e

– sensor well with insulation

– thermometer

– Installation, Operating, Start-up and

Ser ice Instructions

Product Installation

This is a simplified conceptual dra ing only!

Piping and necessary componentry must be

field verified. Proper installation and

functionality in the field are the

responsibility of the heating contractor.

Domestic hot ater connections

Domestic hot water

DHW recirculation line

DHW recirculation pump

Spring-loaded flow check al e

Discharge pipe

Temperature and pressure relief al e

Shutoff al e

Drain

Domestic cold water supply lines

Backflow pre enter

Domestic cold water inlet

Precharged expansion tank

(required where backflow pre enter is

installed; check local plumbing codes

and requirements)

IMPORTANT

Product Installation

∅½’’

ID 15

ID 19.2

AF 24

220

The Vitocell-H 100 tank is approved for

heating systems ith a maximum DHW

supply of up to 150 °F / 65.6 °C only.

Sensor Well

Vitocell-H 100,

with 42 and 53 USG / 160 and 200 ltr

capacity

Vitocell-H 100 domestic hot ater

tank positioned under the boiler

Please note that only the boiler/tank

combinations stated in the Price List are

possible.

Backflo preventers

Where backflow pre enters are required, a

domestic water expansion tank installation

is recommended in the cold water inlet

piping before the cold water enters the

Vitocell. For the backflow de ice, obser e

local plumbing codes and regulations.

Temperature and pressure

relief valve

A temperature and pressure relief al e

(T&P relief al e) is supplied with the tank.

The heating contractor must install the al e

on each tank in a method meeting code

requirements. If local codes require a

different relief al e, substitute the al e

supplied by the manufacturer. The tank is

appro ed for 150 psig. Maximum operating

pressure is 150 psig.

The T&P relief al e supplied with the tank

is tested under ANSI Z21.22 code for Relief

Val es and Automatic Gas Shut-off De ices

for Hot Water Supply Systems.

Since the heat exchanger coil allo s for

high MBH input (see Vitocell flo charts),

confirmation that the appropriate and

correct size pressure and temperature relief

valve is used and installed, is necessary.

Watts Model

40XL-8

150 psig

(US and Canada)

ASME pressure

steam rating

1438 MBH

CSA temperature

steam rating

205 MBH

Relief

temperature

210ºF (99ºC)

Inlet thread

¾” male

Outlet thread

¾” female

Warranty

Our warranty for domestic hot water tanks

states that the water heated must be of

drinking water quality and that any water

treatment equipment in use must function

correctly.

Viessmann accepts no responsibility for

damage howsoe er caused and reser es the

right to withdraw the product warranty if

the product has been improperly installed or

misapplied by the installer, contractor or

final user. In order to qualify for product

warranty, strict adherence to the installation

and ser ice manuals must be assured. In the

e ent that Viessmann non-appro ed

components are utilized, Viessmann

reser es the right to withdraw all expressed

or implied warranties without written notice.

The water to be heated with the Vitocell

must be drinking (potable) water quality. If

the tank is used to heat other media, the

warranty will be null and oid. Damage

resulting from excessi e pressure or

temperature is clearly not the responsibility

of Viessmann.

The amount of chloride and sulfate

acceptable to the tank is limited. In areas

where high concentrations of chloride and

sulfate are present in drinking water, please

consult Viessmann for directions.

IMPORTANT

To ensure optimum, safe operation,

the supplied stainless steel ell must

be installed. The ell diameter is

large enough to accommodate a ide

variety of sensing bulbs.

Al ays use spring clip to ensure

proper contact of capillary bulb

against the stainless steel ell for

proper sensing/heat transfer!

WARNING

IMPORTANT

Vitocell-H 100 Sizing

Continuous Flow Capacity Chart

Vitocell-H 100,

42 USG / 160 ltr capacity

Cur e

Domestic hot water 40 to 113°F / 4 to 45°C

Cur e

Domestic hot water 40 to 140°F / 4 to 60°C

Vitocell-H 100 Sizing

Continuous Flow Capacity Chart

Vitocell-H 100,

53 USG / 200 ltr capacity

Cur e

Domestic hot water 40 to 113°F / 4 to 45°C

Cur e

Domestic hot water 40 to 140°F / 4 to 60°C

Andere Viessmann Kessel Handbücher

Viessmann

Viessmann Vitocell-B 100 CVB Series Bedienungsanleitung

Viessmann

Viessmann CombiPLUS Kit Datenblatt

Viessmann

Viessmann Vitoplex 100 PV1 Betriebsanleitung

Viessmann

Viessmann Vitomax 200-LW M64A Schulungshandbuch

Viessmann

Viessmann VITOROND 100 VR1 40 Kurzanleitung

Viessmann

Viessmann FB2A Betriebsanleitung

Viessmann

Viessmann Vitocrossal 200 CM2 Series Bedienungsanleitung

Viessmann

Viessmann VITODENS 050-W Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Bedienungsanleitung

Viessmann

Viessmann Vitodens 200-W B2HA series Kurzanleitung

Viessmann

Viessmann Vitocrossal 200 CM2 Series Bedienungsanleitung

Viessmann

Viessmann Vitotronic 200 KW2 Kurzanleitung

Viessmann

Viessmann Vitodens 200-W B2HA 100 Gebrauchsanweisung

Viessmann

Viessmann Vitomax LW Schulungshandbuch

Viessmann

Viessmann VITOCROSSAL 300 Bedienungsanleitung

Viessmann

Viessmann VITOPLEX 300 Betriebsanleitung

Viessmann

Viessmann Vitocell 200 Cylinder Benutzerhandbuch

Viessmann

Viessmann Vitocell 050-E Kurzanleitung

Viessmann

Viessmann VITODENS 333 Bedienungsanleitung

Viessmann

Viessmann Vitorond 100 Kurzanleitung

Viessmann

Viessmann VITOLIGNO 300-H Series Bedienungsanleitung

Viessmann

Viessmann Vitodens 100-W Bedienungsanleitung

Viessmann

Viessmann VITOPLEX 100?LS Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 Betriebsanleitung

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung

Radiant

Radiant R2K 55 Handbuch