Viessmann Vitodens series Bedienungsanleitung

Operating instructions VIESMANN

for system users

Heating systems with Vitotronic 100 control unit

for constant temperature operation

VITODENS

5592 453 GB 3/2004 Please keep safe

Please follow these safety instructions closely to prevent accidents and

material losses.

Safety instructions explained

Danger

This symbol warns against the

risk of injury.

!Important information

This symbol warns against the

risk of material losses and

environmental pollution.

Note

Details identified by the words "Note"

contain additional information.

Target group

These operating instructions are

designed for heating system users.

Danger

Incorrect work on the heating

system can lead to life-threa-

tening accidents.

&Work on gas equipment must

only be carried out by a

registered gas fitter.

&Electrical work must only be

carried out by a qualified

electrician.

If you notice a smell of gas

Danger

Escaping gas can lead to

explosions which may lead to

serious injury.

&Do not smoke. Prevent

naked flames and sparks.

Never switch electrical lights

or equipment.

&Open windows and doors.

&Close the gas shut-off valve.

&Remove all personnel from

the danger zone.

&Observe the safety regula-

tions of your local gas sup-

plier which can be found on

the gas meter.

&Notify your heating contrac-

tor from outside the building.

If you smell flue gas

Danger

Flue gas may lead to life-threa-

tening poisoning.

&Shut down the heating sys-

tem.

&Ventilate the boiler room.

&Closealldoorsleadingtothe

living space.

For your safety

Safety instructions

5592 453 GB

If you notice fire

Danger

Fire causes a risk of burns and

explosion.

&Shut down the heating sys-

tem.

&Close the fuel line shut-off

valves.

&Only use suitable approved

fire extinguishers.

Gas fired operation: Fire

class C

Boiler room requirements

!Important information

Incorrect ambient conditions

canleadtodamagetothe

heating system and put safe

operation at risk.

&Ensure temperatures higher

than 0 °C and lower than 35

°C.

&Prevent the air becoming

contaminated by haloge-

nated hydrocarbons (e.g. as

contained in paints, solvents

or cleaning fluids) and exces-

sive dust (e.g. through grind-

ing/polishing work).

&Avoid continuously high

humidity levels (e.g. through

frequent drying of washing).

&Never close existing ventila-

tion apertures.

Fuels

!Important information

Using incorrect fuel can

damage the heating system.

Use only the following types of

fuel:

Natural gas E and LL or LPG.

Ancillary components, spare and

wearing parts

!Important information

Components which are not

tested with the heating system

mayleadtodamagetothe

heating system or may affect

their functions.

Installation or replacement

must only be carried out by

qualified personnel.

For your safety (cont.)

Safety instructions

5592 453 GB

Introduction

Initial start-up ............................................................................................. 6

Your heating system is pre-set at the factory ............................................... 6

Where to find the controls

Summary of controls and indicators ............................................................ 7

&Opening the control unit ........................................................................... 7

&Functions ................................................................................................ 8

&Symbols in the display ............................................................................. 9

Start-up and shutdown

Heating system start-up .............................................................................. 10

Heating system shutdown ........................................................................... 10

Starting a heating circuit and DHW heating/loading ..................................... 11

Starting DHW only ...................................................................................... 12

Shutting down a heating circuit and DHW heating/loading ........................... 12

Adjusting temperatures

Room temperature...................................................................................... 13

Adjusting the boiler water temperature ........................................................ 13

Setting the DHW temperature ..................................................................... 14

Modifying and scanning time programs

General notes............................................................................................. 15

Central heating ........................................................................................... 16

DHW heating .............................................................................................. 17

Scanning options

Scanning information .................................................................................. 19

Special displays

Time and date............................................................................................. 21

Maintenance display................................................................................... 21

What to do if ...

... rooms are too cold? ................................................................................ 23

... rooms are too hot? .................................................................................. 24

... no DHW is available?.............................................................................. 24

... the DHW is too hot? ................................................................................ 25

Scanning fault display................................................................................. 25

Repairs

Cleaning..................................................................................................... 26

Index

5592 453 GB

Inspection and maintenance ....................................................................... 26

Energy saving tips .................................................................................... 28

Keyword index .......................................................................................... 29

Index (cont.)

Index

5592 453 GB

The initial start-up and matching of

the control unit to local conditions and

the structural characteristics of the

building, must be carried out by your

heating contractor.

As the user of new combustion equip-

ment, you are obliged to notify the

installation to your local flue gas

inspector (check local regulations).

Your local flue gas inspector will also

inform you (where appropriate) about

work he may be required to perform

on your combustion equipment (e.g.

regular checks, cleaning).

Your heating system is pre-set at the factory

The control unit is preset at the fac-

tory for "heating and DHW", i.e. the

system delivers central heating and

DHW loading (subject to a DHW cylin-

der being installed). Your heating sys-

tem is therefore ready for use.

You may change the factory settings

in accordance with personal require-

ments.

Note

All data is saved in case of power fail-

ure.

Initial start-up

Introduction

5592 453 GB

You can change all settings for your heating system, centrally, at the control

unit.

You can change the room temperature and time program settings for central

heating at the remote control (see separate operating instructions), provided

your system is equipped with a remote control unit.

Opening the control unit

ACover

BControl unit flap (open to make

adjustments)

Lift up the cover A, and pivot the con-

trol unit flap Bdown. All boiler con-

trols are located behind the control

unit flap.

Ontheinsideofthecontrolunit

flap B, an abridged version of these

operating instructions can be found

behind a further flap. You may remove

the abridged operating instructions

with the flap.

Summary of controls and indicators

Wheretofindthecontrols

5592 453 GB

Functions

AHeating programs (page 11)

BInformation (page 19)

CBasic settings

DConfirmation/acknowledgement

ESetting values

FDHW temperature (page 14)

GEmissions test switch (only for

qualified personnel)

HBoiler water temperature (page

13)

KTime program, DHW heating/load-

ing (page 17)

and DHW circulation (if connected

to the control unit)

LTime/date (page 21)

MCentral heating time program

(page 16)

Basic settings

All modified values are reset to their

factorysettingsbypressinge.

Summary of controls and indicators (cont.)

Wheretofindthecontrols

5592 453 GB

Further displays and controls

APressure gauge

BFault indicator (red)

CON/OFF indicator (green)

DBurner fault reset

EON/OFF switch

Symbols in the display

These symbols are not permanently displayed, but appear subject to the system

version and the operating state. Flashing displays indicate that modifications

canbemade.

rCentral heating or "Boiler

enable" in a multi-boiler system

wDHW loading enabled

pCirculation pump running

Êp DHW loading through a solar

heating system

ABurner "ON"

SEmissions test "ON"

EBurner fault

UFault message

Summary of controls and indicators (cont.)

Wheretofindthecontrols

5592 453 GB

Position of the gas shut-off valve for

Vitodens 333

1. Check the heating system pressure

on the pressure gauge A: The sys-

tem pressure is too low if the nee-

dle indicates below 0.8 bar. In that

case, top up with water or contact

your local heating contractor.

2. For open flue operation:

Thecombustionairisdrawnfrom

the boiler room.

Check whether the ventilation/

exhaust apertures in the boiler

room are open and unobstructed.

3. Open the gas shut-off valve B.

4. Switch ON the mains power supply;

e.g. at a separate fuse or a mains

electrical isolator.

5. ON/OFF switch "8"C;

standby mode is then shown to be

running by the green indicator (ON

indicator); after a short time the boi-

ler temperature will be displayed.

Your heating system and, if

installed, your remote control unit

are now ready for use.

Heating system shutdown

If you temporarily have no need of your heating system, e.g. during a summer

holiday, switch the system to "standby mode"K(see page 12).

Note

The circulation pump will be started for short periods at regular intervals to pre-

vent it from seizing up. These intervals can be modified by your heating contrac-

tor.

Heating system start-up

Start-up and shutdown

5592 453 GB

Andere Handbücher für Vitodens series

Inhaltsverzeichnis

Andere Viessmann Kessel Handbücher

Viessmann

Viessmann VITOCELL 100-V Bedienungsanleitung

Viessmann

Viessmann VITOCONTROL-S, WB2B Bedienungsanleitung

Viessmann

Viessmann VITOPLEX 100 Bedienungsanleitung

Viessmann

Viessmann B1HF Kurzanleitung

Viessmann

Viessmann VITOCROSSAL 200 Betriebsanleitung

Viessmann

Viessmann Vitodens 200-W B2HA series Kurzanleitung

Viessmann

Viessmann Vitodens 222-F Gebrauchsanweisung

Viessmann

Viessmann Vitomax 200-LW M64A Schulungshandbuch

Viessmann

Viessmann Vitocrossal 200 CM2 Series Bedienungsanleitung

Viessmann

Viessmann Vitopend 200-W Betriebsanleitung

Viessmann

Viessmann Vitodens 100-W B1HA 26Vitodens 100-W B1HA 35Vitodens 100-W B1KA... Kurzanleitung

Viessmann

Viessmann Vitorond 100 Kurzanleitung

Viessmann

Viessmann Vitodens 200-W System Kurzanleitung

Viessmann

Viessmann Vitodens 100-W WB1C Bedienungsanleitung

Viessmann

Viessmann Vitola 200 Bedienungsanleitung

Viessmann

Viessmann Vitolig 300 Betriebsanleitung

Viessmann

Viessmann VITODENS 200 Leitfaden

Viessmann

Viessmann Vitodens 100-W Kurzanleitung

Viessmann

Viessmann VITODENS 050-W Kurzanleitung

Viessmann

Viessmann WB2B 45 Bedienungsanleitung

Viessmann

Viessmann VITODENS 100-W P25 Bedienungsanleitung

Viessmann

Viessmann VITODENS 200 WB2 Series Gebrauchsanweisung

Viessmann

Viessmann VITOROND 100 VR1 40 Kurzanleitung

Viessmann

Viessmann Vitodens 200-W System Bedienungsanleitung

Beliebte Kessel Handbücher anderer Marken

Vaillant

Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung

Radijator

Radijator BIO max 23.1 Bedienungsanleitung

Brunner

Brunner BSV 20 Bedienungsanleitung

Buderus

Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung

Potterton

Potterton 50e Datenblatt

UTICA BOILERS

UTICA BOILERS TriFire Bedienungsanleitung

Joannes

Joannes LADY Series Handbuch

ECR International

ECR International UB90-125 Gebrauchsanweisung

Froling

Froling FHG Turbo 3000 Bedienungsanleitung

Froling

Froling P4 Pellet 8 - 105 Bedienungsanleitung

U.S. Boiler Company

U.S. Boiler Company K2 Bedienungsanleitung

Henrad

Henrad C95 FF Bedienungsanleitung

NeOvo

NeOvo EcoNox EF 36 Bedienungsanleitung

Potterton

Potterton PROMAX SL 12 Bedienungsanleitung

Eco Hometec

Eco Hometec EC 25 COMPACT Bedienungsanleitung

Baxi

Baxi Prime 1.24 Bedienungsanleitung

REXNOVA

REXNOVA ISA 20 BITHERMAL Bedienungsanleitung

Radiant

Radiant R2K 55 Handbuch