Viessmann VITOPEND Bedienungsanleitung
Operating instructions
for the system user
VIESMANN
Heating system with the Vitotronic 100 control unit, type HC1B
for constant temperature operation
VITODENS
VITOPEND
5592 683 GB 1/2011 Please keep safe.
2
Please follow these safety instructions closely to prevent accidents and mate-
rial losses.
Safety instructions explained
Danger
This symbol warns against the
risk of injury.
!Please note
This symbol warns against the
risk of material losses and envi-
ronmental pollution.
Note
Details identified by the word "Note" con-
tain additional information.
Target group
These operating instructions are for the
heating system user.
This appliance is not designed to be
used by persons (including children) with
limited physical, sensory or mental
capacities, or lacking experience and/or
knowledge, unless they are supervised
by a person responsible for their safety,
or have received instructions from such
a person as to how to use the appli-
ance.
!Please note
Children should be supervised.
Ensure that children never play
with the appliance.
Danger
Incorrectly executed work on the
heating system can lead to life-
threatening accidents.
■ Work on gas installations must
only be carried out by a regis-
tered gas fitter.
■ Work on electrical equipment
must only be carried out by a
qualified electrician.
If you smell gas
Danger
Escaping gas can lead to explo-
sions which may result in serious
injury.
■ Do not smoke. Prevent naked
flames and sparks. Do not
switch lights or electrical appli-
ances on or off.
■ Close the gas shut-off valve.
■ Open windows and doors.
■ Remove all people from the
danger zone.
■ Notify your gas or electricity
supplier and your local heating
contractor from outside the
building.
■ Shut off the electricity supply to
the building from a safe place
(outside the building).
Safety instructions
For your safety
5592 683 GB
3
If you smell flue gas
Danger
Flue gas can lead to life-threat-
ening poisoning.
■ Shut down the heating system.
■ Ventilate the boiler room.
■ Close all doors in the living
space.
In case of fire
Danger
Fire creates the risk of burning
and explosions.
■ Shut down the heating system.
■ Close the shut-off valves of the
fuel lines.
■ Use a tested fire extinguisher,
class ABC.
Boiler room requirements
!Please note
Incorrect ambient conditions can
lead to damage to the heating
system and put the safe opera-
tion at risk.
■ Ensure ambient temperatures
above 0 ºC and below 35 ºC.
■ Prevent air contamination by
halogenated hydrocarbons
(e.g. as contained in paints,
solvents or cleaning fluids) and
excessive dust (e.g. through
grinding/polishing work).
■ Avoid continuously high humid-
ity levels (e.g. through frequent
drying of washing).
■ Never close existing ventilation
apertures.
Auxiliary components, spare and
wearing parts
!Please note
Components which are not tes-
ted with the heating system may
lead to damage to the heating
system, or may affect their vari-
ous functions.
Installation or replacement work
must only be carried out by quali-
fied personnel.
Safety instructions
For your safety (cont.)
5592 683 GB
4
Introductory information
Commissioning..................................................................................................... 6
Your system is preset at the factory..................................................................... 6
Terminology.......................................................................................................... 7
Tips on saving energy.......................................................................................... 7
Operation
Controls................................................................................................................ 8
How to use the controls........................................................................................ 9
Symbols................................................................................................................ 9
Start-up/shutdown
Starting the heating system.................................................................................. 10
Shutting down the heating system....................................................................... 11
■ With frost protection monitoring........................................................................ 11
■ Without frost protection monitoring (shutdown)................................................ 11
Central heating
Required settings for central heating.................................................................... 12
Setting the heating flow temperature.................................................................... 12
Setting the heating program (central heating)...................................................... 12
Stopping the central heating................................................................................. 13
DHW heating
Required settings (DHW heating)......................................................................... 14
Setting the DHW temperature.............................................................................. 14
Setting the heating program (DHW heating)........................................................ 14
Stopping the DHW heating................................................................................... 15
Comfort function (if available)............................................................................... 15
Further adjustments
Setting the temperature unit (°C/°F)..................................................................... 17
Restoring factory settings..................................................................................... 17
Scanning
Scanning information............................................................................................ 18
Scanning the service messages........................................................................... 19
Scanning fault messages..................................................................................... 20
Multi boiler systems
Special considerations for multi boiler systems.................................................... 22
Emissions test mode......................................................................................... 23
Index
Index
5592 683 GB
5
What to do if...
Rooms are too cold.............................................................................................. 24
Rooms are too hot................................................................................................ 25
There is no hot water............................................................................................ 25
The DHW is too hot.............................................................................................. 26
"ã" flashes on the display .................................................................................. 26
"E" flashes on the display .................................................................................. 26
"ë" flashes on the display .................................................................................. 27
Maintenance........................................................................................................ 28
Keyword index.................................................................................................... 31
Index
Index (cont.)
5592 683 GB
6
The commissioning and matching of the
control unit to local conditions and build-
ing characteristics, as well as instructing
the user in the operation of the system,
must be carried out by your heating con-
tractor.
As the user of new combustion equip-
ment, you may be obliged to notify your
local flue gas inspector of the installation
[check local regulations]. Your local flue
gas inspector will also inform you [where
appropriate] about work he may be
required to carry out on your combustion
equipment (e.g. regular checks, clean-
ing).
Your system is preset at the factory
The control unit is factory-set to " "
for central heating and DHW heating.
Your heating system is therefore ready
for use:
Central heating
■ The rooms are heated in accordance
with the settings on your control unit
and room temperature control unit.
■ Your heating contractor can make fur-
ther settings for you during commis-
sioning.
You can change any settings individu-
ally at any time to suit your require-
ments (see chapter "Central heating").
DHW heating
■ The DHW is heated to 50 °C.
■ Your heating contractor can make fur-
ther settings for you during commis-
sioning.
You can change any settings individu-
ally at any time to suit your require-
ments (see chapter "DHW heating").
Frost protection
■ Your boiler and DHW cylinder are pro-
tected against frost.
Power failure
■ All data is saved if there is a power
failure.
Introductory information
Commissioning
5592 683 GB
7
To provide you with a better understand-
ing of the functions of your control unit,
the appendix contains the chapter "Ter-
minology" (see page 29).
Tips on saving energy
Utilise the setting options on the control
unit and the room temperature control
unit:
■ Never overheat your rooms. Every
degree by which the room temperature
is reduced saves up to 6 % on heating
costs.
Never set your room temperature
higher than 20 °C (see page 12).
■ Never set the DHW temperature too
high (see page 14).
■ Select the heating program that meets
your current requirements:
– In the summer, if you do not want to
heat any rooms but require hot
water, select the " " heating pro-
gram (see page 14).
– If you do not want to heat any rooms
and require no hot water for a pro-
longed period of time, select the
" " heating program (see
page 11).
Further recommendations:
■ Correct ventilation/airing.
Briefly open windows fully and at the
same time close the thermostatic radi-
ator valves.
■ Close roller shutters (if installed) at
dusk.
■ Set thermostatic valves correctly.
■ Never cover radiators or thermo-
static valves.
■ Controlled DHW consumption: A
shower generally uses less energy
than a full bath.
Introductory information
Terminology
5592 683 GB
8
You can change the settings for your
heating system centrally at the program-
ming unit of the control unit.
If you have a room temperature control
unit installed in your rooms, you can also
change the settings on the room temper-
ature control unit.
Room temperature control unit
operating instructions
Note
The programming unit can be placed in
a wall mounting base. This is available
as an accessory. Ask your heating con-
tractor for more information.
4 8°C
s A
Takes you one step back in the
menu
Cursor keys
To scroll in the menu or set values
OK Enables you to confirm your selec-
tions or setting
No function
Enables you to call up the menu for
settings and scanning
Operation
Controls
5592 683 GB
9
Standard display
4 8°C
Press . This takes you to the menu for
settings and scanning.
Symbols
These symbols are not always dis-
played, but appear subject to the system
version and the operating state. Flashing
displays indicate that modifications can
be made.
Menu
Central heating
DHW heating
Information
Emissions test mode
Additional settings
Heating program
Frost protection monitoring
(standby mode)
DHW heating
Central heating and DHW heat-
ing
COMF Comfort mode for DHW heating
ECO Without comfort mode for DHW
heating
Messages
Service message
The service interval has expired
Fault message
Fault message for burner
Displays
Temperature
Frost protection monitoring
Central heating
Heating circuit pump running
Cylinder primary pump running
In conjunction with a solar thermal
system:
Solar circuit pump is running
Burner running
Standard factory setting
Operation
How to use the controls
5592 683 GB
10
0
123
4
bar
C D
E
BA
4 8°C
s A
AFault indicator (red)
BON indicator (green)
CReset button
DON/OFF switch
EPressure gauge
1. Check the heating system pressure
at the pressure gauge. The system
pressure is too low if the indicator
points to the area below 1.0 bar. In
this case, top up with water or notify
your local heating contractor.
2. For open flue operation:
Check that the ventilation apertures
of the installation room are open and
unrestricted.
Note
With open flue operation, the com-
bustion air is drawn from the installa-
tion room.
3. Open the gas shut-off valve.
Note
Ask your heating contractor to
explain the positioning and handling
of these components.
4. Switch ON the power supply, e.g. at
a separate MCB/fuse or a mains iso-
lator.
5. Turn the ON/OFF switch " " ON.
After a short time, the standard dis-
play appears and the green ON indi-
cator illuminates. Your heating sys-
tem and room temperature control
unit are now ready for operation.
Start-up/shutdown
Starting the heating system
5592 683 GB
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Viessmann Kessel Handbücher
Viessmann
Viessmann Vitocrossal 300 CT3 SERIES Betriebsanleitung
Viessmann
Viessmann Vitodens 200-W WB2B Series Bedienungsanleitung
Viessmann
Viessmann Vitoladens 300-C Kurzanleitung
Viessmann
Viessmann Vitomax LW M64 Series Bedienungsanleitung
Viessmann
Viessmann Vitocrossal 300 CA3B Bedienungsanleitung
Viessmann
Viessmann Vitodens 222-W B2LB Bedienungsanleitung
Viessmann
Viessmann Vitocrossal Bedienungsanleitung
Viessmann
Viessmann Vitodens 100 WB1A Kurzanleitung
Viessmann
Viessmann Vitodens 222-F Bedienungsanleitung
Viessmann
Viessmann Vitodens 222-F Bedienungsanleitung
Viessmann
Viessmann Vitodens 100-W WB1B Series Kurzanleitung
Viessmann
Viessmann VITOLIGNO 300-C Bedienungsanleitung
Viessmann
Viessmann Vitoligno 250-S Betriebsanleitung
Viessmann
Viessmann Vitodens 100-W Kurzanleitung
Viessmann
Viessmann Vitodens 100 Bedienungsanleitung
Viessmann
Viessmann VITODENS 200 WB2A Versionshinweis
Viessmann
Viessmann B2HA 19 Bedienungsanleitung
Viessmann
Viessmann Vitodens 242-F Kurzanleitung
Viessmann
Viessmann VITOCROSSAL 200 Bedienungsanleitung
Viessmann
Viessmann VITOPLEX 100 Betriebsanleitung
Beliebte Kessel Handbücher anderer Marken
Vaillant
Vaillant uniSTOR VIH SW GB 500 BES Bedienungsanleitung
Radijator
Radijator BIO max 23.1 Bedienungsanleitung
Brunner
Brunner BSV 20 Bedienungsanleitung
Buderus
Buderus Logamax GB062-24 KDE H V2 Bedienungsanleitung
Potterton
Potterton 50e Datenblatt
UTICA BOILERS
UTICA BOILERS TriFire Bedienungsanleitung
