Viessmann VITOSOLIC 100 Kurzanleitung
Installation and service
instructions
for contractors
VIESMANN
Electronic temperature differential control unit
Vitosolic 100
Type SD1
For applicability, see the last page
VITOSOLIC 100
5369 987 GB 4/2009 Please keep safe.
2
Please follow these safety instructions closely to prevent accidents and mate-
rial losses.
Safety instructions explained
Danger
This symbol warns against the
risk of injury.
!Please note
This symbol warns against the
risk of material losses and envi-
ronmental pollution.
Note
Details identified by the word "Note" con-
tain additional information.
Target group
These instructions are exclusively
designed for qualified personnel.
■ Work on electrical equipment must
only be carried out by a qualified elec-
trician.
■ The system must be commissioned by
the system installer or a qualified per-
son authorised by the installer.
Regulations
Observe the following when working on
this system
■ all legal instructions regarding the pre-
vention of accidents,
■ all legal instructions regarding envi-
ronmental protection,
■ the Code of Practice of relevant trade
associations.
■ all current safety regulations as
defined by DIN, EN, DVGW, VDE and
all locally applicable standards
Working on the system
■ Isolate the system from the power sup-
ply and check that it is no longer 'live',
e.g. by removing a separate fuse or by
means of a main isolator.
■ Safeguard the system against unau-
thorised reconnection.
!Please note
Electronic modules can be dam-
aged by electrostatic dis-
charges.
Touch earthed objects, such as
heating or water pipes, to dis-
charge static loads.
Repair work
!Please note
Repairing components that fulfil a
safety function can compromise
the safe operation of your heating
system.
Replace faulty components only
with original Viessmann spare
parts.
Safety instructions
Safety instructions
5369 987 GB
3
Ancillary components, spare and
wearing parts
!Please note
Spare and wearing parts that
have not been tested together
with the heating system can com-
promise its function. Installing
non-authorised components and
non-approved modifications or
conversions can compromise
safety and may invalidate our
warranty.
For replacements, use only orig-
inal spare parts supplied or
approved by Viessmann.
Safety instructions
Safety instructions (cont.)
5369 987 GB
4
Installation instructions
Preparing for installation
Installation information......................................................................................... 6
System example 1................................................................................................ 6
System example 2................................................................................................ 11
System example 3................................................................................................ 18
System example 4................................................................................................ 24
Installation sequence
Fitting the solar control unit.................................................................................. 35
Overview of electrical connections....................................................................... 36
Solar circuit pump................................................................................................. 36
Pump/valve at output R2...................................................................................... 38
High limit safety cut-out........................................................................................ 39
Collector temperature sensor............................................................................... 40
Cylinder temperature sensor................................................................................ 41
Temperature sensor............................................................................................. 41
Power supply........................................................................................................ 42
Service instructions
Commissioning
Switching the power ON....................................................................................... 44
Navigation through the menu............................................................................... 44
Selecting the system scheme............................................................................... 44
Setting system parameters................................................................................... 45
Resetting system parameters............................................................................... 45
Carrying out a relay test....................................................................................... 45
Service scans
Scanning temperatures and operating conditions................................................ 46
Troubleshooting
Fault messages.................................................................................................... 47
Checking sensors................................................................................................. 47
Changing the fuse................................................................................................ 48
Function description
Parameter overview............................................................................................. 49
System scheme.................................................................................................... 51
Collector limit temperature................................................................................... 62
Collector cooling function..................................................................................... 62
Minimum collector temperature limit..................................................................... 62
Index
Index
5369 987 GB
5
Frost protection function....................................................................................... 63
Reverse cooling function...................................................................................... 63
Interval function.................................................................................................... 63
Heat statement..................................................................................................... 64
Speed control....................................................................................................... 64
Parts list.............................................................................................................. 66
Specification....................................................................................................... 67
Appendix............................................................................................................. 68
Certificates
Declaration of conformity...................................................................................... 69
Keyword index.................................................................................................... 70
Index
Index (cont.)
5369 987 GB
6
Danger
Subject to system configuration,
DHW temperatures above 60 °C
can occur. DHW with tempera-
tures in excess of 60 °C can result
in scalding.
To limit the temperature to 60 °C,
install mixing equipment, e.g. a
thermostatically controlled mix-
ing valve (accessory). Install a
mixer tap as anti-scalding device
at the draw-off point.
System example 1
DHW heating with dual-mode DHW cylinder
Main components
■ Viessmann solar collectors
■ DHW cylinders Vitocell 100-B or
Vitocell 300-B
■ Vitosolic 100, type SD1
■ Solar-Divicon
■ Wall mounted oil/gas boiler or oil/gas
boiler
Function description
DHW heating with solar energy
Solar circuit pump R1 eE starts and
DHW cylinder qP is heated up if the tem-
perature differential between collector
temperature sensor S1 eQ and cylinder
temperature sensor S2 qQ exceeds the
starting temperature differential DT E.
Solar circuit pump R1 eE is stopped in
accordance with the following criteria:
■ The actual temperature falls below the
shutdown temperature differential
DT A.
■ Exceeding the electronic temperature
limit (max. 90°C) of control unit eZ
■ Reaching the temperature selected at
high limit safety cut-out qW (if installed)
Auxiliary function for DHW heating
The requirements for the auxiliary func-
tion are achieved through circulation
pump R2 qT.
Suppression of DHW cylinder reheat-
ing by the boiler
Coding address "67" in boiler control unit
2 defaults a third set DHW temperature
(setting range 10 to 95 °C). This value
must be below the first set DHW temper-
ature. DHW cylinder qP will only be
heated by boiler 1 (solar circuit
pump R1 eE runs) if this set value cannot
be achieved by the solar thermal sys-
tem.
DHW heating without solar energy
The upper section of DHW cylinder qP is
heated by boiler 1. The cylinder ther-
mostat with cylinder temperature sen-
sor 3 of boiler control unit 2 regulates
cylinder heating.
Preparing for installation
Installation information
5369 987 GB
7
Required settings on the solar control unit
Param
eters
Delivered
condition
Description Setting
ANL 1 Without auxiliary function for DHW heating 1
With auxiliary function for DHW heating (see
page 56)
4
DT E 8 K Start temperature differential for solar circuit pump
at R1
DT A 4 K Stop temperature differential for solar circuit pump
at R1
S SL 60 °C Set cylinder temperature (see page 53)
For further functions, see chapter "Functions" from page 49.
Note
"DT E" can be set at least 0.5 K higher
than "DT A".
"DT A" can be set up to 0.5 K below
"DT E".
Information regarding speed control
of the solar circuit pump
Observe chapter "Speed control" (see
page 64).
Preparing for installation
System example 1 (cont.)
5369 987 GB
Installation
8
Hydraulic installation diagram
qQ
qE
3
qP
qT
qR
qW
N
eP
eW
eQ
eE
1
2
M
eZ
4
2
11
Preparing for installation
System example 1 (cont.)
5369 987 GB
9
Equipment required
Pos. Description
1Oil/gas boiler or wall mounted oil/gas boiler
with
2Boiler and heating circuit control unit
3Cylinder temperature sensor
4Circulation pump for cylinder heating
(integrated for wall mounted oil/gas boiler)
qP Dual-mode DHW cylinder
qQ Cylinder temperature sensor S2
qW High limit safety cut-out (accessory)
qE DHW circulation pump (on site)
(internal/external extension may be required for connecting a wall mounted
oil/gas boiler)
qR Thermostatic mixing valve (accessory)
qT Circulation pump R2 (anti-stratification) (on site)
eP Solar collectors
eQ Collector temperature sensor S1
eW Solar-Divicon (accessory)
with
eE Solar circuit pump R1
eZ Vitosolic 100, type SD1
eU Junction box (on site)
eI ON/OFF switch (on site)
Preparing for installation
System example 1 (cont.)
5369 987 GB
Installation
10
Electrical installation diagram
eQ
qQ
qW
eE
eZ
230 V / 50 Hz
?
21
20
15
19
18
14
?
M
1~ R1
17
16
13
?
12
11
145
10
9
4
3
2
1
6
5
eU
SOL
KOL
High limit safety cut-out
230 V / 50 HzLow voltage
R2
M
1~ qT
KM BUS 2
eI
Preparing for installation
System example 1 (cont.)
5369 987 GB
Andere Handbücher für VITOSOLIC 100
7
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Viessmann Steuereinheit Handbücher
Viessmann
Viessmann EM-EA1 extension Kurzanleitung
Viessmann
Viessmann SM1 Kurzanleitung
Viessmann
Viessmann VITOTRONIC 100 Kurzanleitung
Viessmann
Viessmann SDIO/SM1A Kurzanleitung
Viessmann
Viessmann 5222 Bedienungsanleitung
Viessmann
Viessmann VITOTRONIC 100 Kurzanleitung
Viessmann
Viessmann Vitotronic 100 GC1 Leitfaden
Viessmann
Viessmann Vitotrol 350-C Bedienungsanleitung
Viessmann
Viessmann SM1 Kurzanleitung
Viessmann
Viessmann EM-M1 Kurzanleitung
Viessmann
Viessmann VITOTRONIC300 Kurzanleitung
Viessmann
Viessmann 5557 Bedienungsanleitung
Viessmann
Viessmann 5096 Bedienungsanleitung
Viessmann
Viessmann SCU 123 Bedienungsanleitung
Viessmann
Viessmann 5223 Bedienungsanleitung
Viessmann
Viessmann EM-EA1 extension Betriebsanleitung
Viessmann
Viessmann 5569 Bedienungsanleitung
Viessmann
Viessmann VITOTRONIC SPS Betriebsanleitung
Viessmann
Viessmann 5204 Bedienungsanleitung
Viessmann
Viessmann VITOTRONIC 100 Betriebsanleitung
Beliebte Steuereinheit Handbücher anderer Marken
Festo
Festo Compact Performance CP-FB6-E Stücklistenhandbuch
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Bedienungsanleitung
JS Automation
JS Automation MPC3034A Bedienungsanleitung
JAUDT
JAUDT SW GII 6406 Series Kurzanleitung
Spektrum
Spektrum Air Module System Bedienungsanleitung
BOC Edwards
BOC Edwards Q Series Bedienungsanleitung
