ViewSonic VA1917a Bedienungsanleitung

VA1917a

Display

User Guide

Model No. VS16023

IMPORTANT: Please read this User Guide to obtain important information on installing

and using your product in a safe manner, as well as registering your product for future

service. Warranty information contained in this User Guide will describe your limited

coverage from ViewSonic Corporation, which is also found on our web site at http://

www.viewsonic.com in English, or in specic languages using the Regional selection

box in the upper right corner of our website. “Antes de operar su equipo lea cu

idadosamente las instrucciones en este manual”

Thank you for choosing ViewSonic

Withover25yearsasaworldleadingproviderofvisualsolutions,ViewSonic

is dedicated to exceeding the world’s expectations for technological

evolution, innovation, and simplicity. At ViewSonic, we believe that our

products have the potential to make a positive impact in the world, and

we are confident that the ViewSonic product you have chosen will serve

you well.

Once again, thank you for choosing ViewSonic !

Compliance Information

NOTE: This section addresses all connected requirements and statements regarding

regulations. Confirmed corresponding applications shall refer to nameplate labels

and relevant markings on unit.

FCC Compliance Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this

device must accept any interference received, including interference that may cause

undesired operation.

This equipment has been tested and found to comply with the limits for a Class

B digital device, pursuant to part 15 of the FCC Rules. These limits are designed

to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses, and can radiate radio frequency

energy, and if not installed and used in accordance with the instructions, may cause

harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined

by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modifications not expressly approved

by the party responsible for compliance could void your authority to operate the

equipment.

Industry Canada Statement

CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

The device complies with the EMC Directive 2004/108/EC and Low Voltage

Directive 2006/95/EC.

Following information is only for EU-member states:

The mark shown to the right is in compliance with the Waste Electrical and

Electronic Equipment Directive 2012/19/EU (WEEE).The mark indicates

the requirement NOT to dispose the equipment as unsorted municipal

waste, but use the return and collection systems according to local law.

TCO Information

Congratulations!

This product is TCO Certified – for Sustainable IT

TCO Certified is an international third party sustainability certification for IT

products. TCO Certified ensures that the manufacture, use and recycling of IT

products reflect environmental, social and economic responsibility. Every TCO

Certified product model is verified by an accredited independent test

laboratory.

This product has been verified to meet all the criteria in TCO Certified, including:

Corporate Social Responsibility

Socially responsible production - working conditions and labor law in manufacturing country

Energy Efficiency

Energy efficiency of product and power supply. Energy Star compliant, where applicable.

Environmental Management System

Manufacturer must be certified according to either ISO 14001 or EMAS.

Minimization of Hazardous Substances

Limits on cadmium, mercury, lead & hexavalent chromium including requirements for mercury-free

products, halogenated substances and hazardous flame retardants.

Design for Recycling

Coding of plastics for easy recycling. Limit on the number of different plastics used.

Product Lifetime, Product Take Back

Minimum one-year product warranty. Minimum three-year availability of spare parts. Product take-

back.

Packaging

Limits on hazardous substances in product packaging. Packaging prepared for recycling

Ergonomic, User-centered design

Visual ergonomics in products with a display. Adjustability for user comfort (displays, headsets)

Acoustic performance – protection against sound spikes (headsets) and fan noise (projectors, com-

puters) Ergonomically designed keyboard (notebooks)

Electrical Safety, minimal electro-magnetic Emissions

Third Party Testing

All certified product models have been tested in an independent, accredited laboratory.

A detailed criteria set is available for download at www.tcodevelopment.com, where you can also find

a searchable database of all TCO Certified IT products.

TCO Development, the organization behind TCO Certified, has been an international driver in the

field of Sustainable IT for 20 years. Criteria in TCO Certified are developed in collaboration with

scientists, experts, users and manufacturers. Organizations around the world rely on TCO Certified as

a tool to help them reach their sustainable IT goals. We are owned by TCO, a non-profit organization

representing office workers. TCO Development is headquartered in Stockholm, Sweden, with regional

presence in North America and Asia.

For more information, please visit

www.tcodevelopment.com

iii

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive

2011/65/EU of the European Parliament and the Council on restriction of the use

of certain hazardous substances in electrical and electronic equipment (RoHS2

Directive), and is deemed to comply with the maximum concentration values issued

by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Proposed Maximum

Concentration

Actual Concentration

Lead (Pb) 0.1% < 0.1%

Mercury (Hg) 0.1% < 0.1%

Cadmium (Cd) 0.01% < 0.01%

Hexavalent Chromium (Cr6+) 0.1% < 0.1%

Polybrominated biphenyls (PBB) 0.1% < 0.1%

Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex III

of the RoHS2 Directives as noted below:

Examples of exempted components are:

1. Mercury in cold cathode uorescent lamps and external electrode uorescent

lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):

(1) Short length (≦500 mm): maximum 3.5 mg per lamp.

(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.

(3) Long length (＞1,500 mm): maximum 13 mg per lamp.

2. Lead in glass of cathode ray tubes.

3. Lead in glass of uorescent tubes not exceeding 0.2% by weight.

4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.

5. Copper alloy containing up to 4% lead by weight.

6. Lead in high melting temperature type solders (i.e. lead-based alloys containing

85% by weight or more lead).

7. Electrical and electronic components containing lead in a glass or ceramic other

than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or

ceramic matrix compound.

Indian Restriction of Hazardous Substances

Restriction on Hazardous Substances statement (India) This product complies

with the “India E-waste Rule 2011” and prohibits use of lead, mercury, hexavalent

chromium, polybrominated biphenyls or polybrominated diphenyl ethers in

concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for

the exemptions set in Schedule 2 of the Rule.

Cautions and Warnings

1. Read these instructions completely before using the equipment.

2. Keep these instructions in a safe place.

3. Heed all warnings and follow all instructions.

4. Sit at least 18” / 45cm from the display.

5. Always handle the display with care when moving it.

6. Never remove the rear cover. This display contains high-voltage parts. You may

be seriously injured if you touch them.

7. Do not use this equipment near water. Warning: To reduce the risk of fire or

electric shock, do not expose this apparatus to rain or moisture.

8. Avoid exposing the display to direct sunlight or another heat source. Orient the

display away from direct sunlight to reduce glare.

9. Clean with a soft, dry cloth. If further cleaning is required, see “Cleaning the

Display” in this guide for further instructions.

10. Avoid touching the screen. Skin oils are difficult to remove.

11. Do not rub or apply pressure to the display panel, as it may permanently damage

the screen.

12. Do not block any ventilation openings. Install the equipment in accordance with

the manufacturer’s instructions.

13. Do not install near any heat sources such as radiators, heat registers, stoves, or

other devices (including amplifiers) that produce heat.

14. Place the display in a well ventilated area. Do not place anything on the display

that prevents heat dissipation.

15. Do not place heavy objects on the display, video cable, or power cord.

16. If smoke, an abnormal noise, or a strange odor is present, immediately switch the

display off and call your dealer or ViewSonic. It is dangerous to continue using

the display.

17. Do not attempt to circumvent the safety provisions of the polarized or grounding-

type plug. A polarized plug has two blades with one wider than the other. A

grounding type plug has two blades and a third grounding prong. The wide blade

and the third prong are provided for your safety. If the plug does not fit into your

outlet, consult an electrician for replacement of the outlet.

18. Protect the power cord from being tread upon or pinched, particularly at the plug,

and the point where if emerges from the equipment. Be sure that the power outlet

is located near the equipment so that it is easily accessible.

19. Only use attachments/accessories specified by the manufacturer.

(Continued on next page)

20. Use only with the cart, stand, tripod, bracket, or table specified by

the manufacturer, or sold with the equipment. When a cart is used,

use caution when moving the cart/equipment combination to avoid

injury from tipping over.

21. Unplug this equipment when it will be unused for long periods of time.

22. Refer all servicing to qualified service personnel. Service is required when the

unit has been damaged in any way, such as: if the power-supply cord or plug is

damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed

to rain or moisture, or if the unit does not operate normally or has been dropped.

Contents

Compliance Information

FCC Compliance Statement...................................................................................i

Industry Canada Statement....................................................................................i

CE Conformity for European Countries..................................................................i

TCO Information....................................................................................................ii

Declaration of RoHS2 Compliance....................................................................... iii

Indian Restriction of Hazardous Substances........................................................ iii

Cautions and Warnings ........................................................................................iv

Product Registration..............................................................................................2

For Your Records ..................................................................................................2

Getting Started

Package Contents .................................................................................................3

Quick Installation ...................................................................................................4

Wall Mounting (Optional).......................................................................................5

Using the Display

Setting the Timing Mode........................................................................................6

OSD and Power Lock Settings..............................................................................6

Adjusting the Screen Image ..................................................................................7

Main Menu Controls ..............................................................................................8

Main Menu Explanation.........................................................................................8

Power Management ..............................................................................................9

Other Information

Specifications ......................................................................................................10

Cleaning the Display............................................................................................11

Troubleshooting...................................................................................................12

Customer Support ...............................................................................................13

Limited Warranty .................................................................................................14

Mexico Limited Warranty.....................................................................................16

Macintosh and Power Macintosh are registered trademarks of Apple Inc.

Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft

Corporation in the United States and other countries.

ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered

trademarks of ViewSonic Corporation.

VESA is a registered trademark of the Video Electronics Standards Association.

DPMS, DisplayPort, and DDC are trademarks of VESA.

ENERGY STAR®is a registered trademark of the U.S. Environmental Protection

Agency (EPA).

As an ENERGY STAR®partner, ViewSonic Corporation has determined that this

product meets the ENERGY STAR®guidelines for energy efficiency.

Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors

or omissions contained herein; nor for incidental or consequential damages resulting

from furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves

the right to change product specifications without notice. Information in this

document may change without notice.

No part of this document may be copied, reproduced, or transmitted by any means,

for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To fulfill possible future product needs, and to receive additional product information

as it becomes available, please visit your region section on ViewSonic’s website to

Registering your product will best prepare you for future customer service needs.

Please print this user guide and fill the information in the “For Your Records” section.

Your display serial number is located on the rear side of the display.

For additional information, please see the “Customer Support” section in this guide.

For Your Records

Product Name:

Model Number:

Document Number:

Serial Number:

Purchase Date:

VA1917a

ViewSonic Widescreen Display

VS16023

VA1917a_UG_ENG Rev. 1A 09-12-14

Proper product disposal is necessary at the end of product life

ViewSonic respects the environment and is committed to working and living green.

Thank you for being part of a Smarter, Greener Computing effort.

Please visit the ViewSonic website to learn more.

USA & Canada: http://www.viewsonic.com/company/green/recycle-program/

Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/

Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere ViewSonic LCD-Display Handbücher

ViewSonic

ViewSonic VP2772 Bedienungsanleitung

ViewSonic

ViewSonic CDX5552 Bedienungsanleitung

ViewSonic

ViewSonic VX2410MH-LED Bedienungsanleitung

ViewSonic

ViewSonic TD2240 Bedienungsanleitung

ViewSonic

ViewSonic VA2445-LED Bedienungsanleitung

ViewSonic

ViewSonic VG930M - 19" LCD Monitor Bedienungsanleitung

ViewSonic

ViewSonic VA1947a-LED Bedienungsanleitung

ViewSonic

ViewSonic VA2249S Bedienungsanleitung

ViewSonic

ViewSonic VA2626wm - 26" LCD Monitor Bedienungsanleitung

ViewSonic

ViewSonic VA2349S Bedienungsanleitung

ViewSonic

ViewSonic VP2365-LED Bedienungsanleitung

ViewSonic

ViewSonic VA2746-LED Bedienungsanleitung

ViewSonic

ViewSonic VA903m Bedienungsanleitung

ViewSonic

ViewSonic VG2230WM - 22" LCD Monitor Bedienungsanleitung

Beliebte LCD-Display Handbücher anderer Marken

Panasonic

Panasonic TH-42LFE7W Bedienungsanleitung

Sony

Sony SDM-S51 Bedienungsanleitung

Acer

Acer DA221HQL Bedienungsanleitung

Data Display

Data Display Regal Bridgeport Bedienungsanleitung

Philips

Philips BDL4988XL Bedienungsanleitung

Data Display

Data Display Calhoon High Bedienungsanleitung

Samsung

Samsung S22E360H Bedienungsanleitung

Data Display

Data Display Colonial Mall Bedienungsanleitung

Data Display

Data Display Great Hills Bedienungsanleitung

Philips

Philips Brilliance 240B4 Bedienungsanleitung

Data Display

Data Display Mr. Sign Bedienungsanleitung

Sceptre

Sceptre X325BV-FMQC Bedienungsanleitung

Orion

Orion OLS-32 Bedienungsanleitung

Data Display

Data Display Farmingville FD Bedienungsanleitung

Data Display

Data Display Setauket Fire Dept. Bedienungsanleitung

I-Tech

I-Tech iAP-3200W Bedienungsanleitung

I-Tech

I-Tech iAP-W2150 Bedienungsanleitung

Data Display

Data Display Town of Dewitt Bedienungsanleitung