ViewSonic EP1020r Bedienungsanleitung
-UserGuide
EP1020r/EP1021r
MultimediaDigitalPoster
ViewSonic™
ModelNo.:VS13489
ViewSonic EP1020r/EP1021r i
ComplianceInformation
ForU.S.A.
This device complies with part 15 of FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modications not expressly approved by the party
responsible for compliance could void your authority to operate the equipment.
ForCanada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
CEConformityforEuropeanCountries
The device complies with the EMC Directive 2004/108/EC and Low Voltage Directive
2006/95/EC.
FollowinginformationisonlyforEU-memberstates:
The mark shown to the right is in compliance with the Waste Electrical and Electronic
Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment as unsorted
municipal waste, but use the return and collection systems according to local law.
If the batteries, accumulators and button cells included with this equipment, display
the chemical symbol Hg, Cd, or Pb, then it means that the battery has a heavy metal
content of more than 0.0005% Mercury or more than, 0.002% Cadmium, or more than
0.004% Lead.
ViewSonic EP1020r/EP1021r ii
FCCRadiationExposureStatement
This equipment should be installed and operated with minimum distance 20cm between the
radiator & your body.
This wireless module device complies with part 15 of FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired
operation.
IndustryCanadaNotice
This device complies with Canadian RSS-210.To prevent radio interference to the licensed
service, this device is intended to be operated indoors and away from windows to provide
maximum shielding. Equipment (or its transmitting antenna) that is installed outdoors is subject
to licensing. The installer of this radio equipment must ensure that the antenna is located or
pointed such that it does not emit RF eld in excess of Health Canada limits for the general
population; consult Safety Code 6, obtainable from Health Canada’s web site www.hc-sc.gc.ca/
rpb.
R&TTEComplianceStatement
This device complies with the Essential Requirements of the R&TTE Directive of the European
Union (1999/5/EC). This equipment meets the following conformance standards:
ETSI EN 300 328
EN 301 489-01
EN 301 489-17
EN 62311
NotiedCountries:Germany, UK, Netherlands, Belgium, Sweden, Denmark, Finland, France,
Italy, Spain, Austria, Ireland, Portugal, Greece, Luxembourg, Estonia, Latvia, Lithuania, Czech
Republic, Slovakia, Slovenia, Hungary, Poland and Malta.
ViewSonic EP1020r/EP1021r iii
ImportantSafetyInstructions
1. Read these instructions completely before using the equipment.
2. Keep these instructions in a safe place.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this equipment near water. Warning: To reduce the risk of re or electric shock,
do not expose this apparatus to rain or moisture.
6. Do not block any ventilation openings. Install the equipment in accordance with the
manufacturer’s instructions.
7. Do not install near any heat sources such as radiators, heat registers, stoves, or other
devices (including ampliers) that produce heat.
8. Do not attempt to circumvent the safety provisions of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A grounding type plug has
two blades and a third grounding prong. The wide blade and the third prong are provided for
your safety. If the plug does not t into your outlet, consult an electrician for replacement of
the outlet.
9. Protect the power cord from being tread upon or pinched, particularly at the plug, and the
point where if emerges from the equipment. Be sure that the power outlet is located near the
equipment so that it is easily accessible.
10. Only use attachments/accessories specied by the manufacturer.
11. Use only with the cart, stand, tripod, bracket, or table specied by the
manufacturer, or sold with the equipment. When a cart is used, use caution
when moving the cart/equipment combination to avoid injury from tipping over.
12. Unplug this equipment when it will be unused for long periods of time.
13. Refer all servicing to qualied service personnel. Service is required when the unit has been
damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid is spilled
onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if the unit does
not operate normally or has been dropped.
ViewSonic EP1020r/EP1021r iv
DeclarationofRoHSCompliance
This product has been designed and manufactured in compliance with Directive 2002/95/
EC of the European Parliament and the Council on restriction of the use of certain hazardous
substances in electrical and electronic equipment (RoHS Directive) and is deemed to comply
with the maximum concentration values issued by the European Technical Adaptation
Committee (TAC) as shown below:
Substance
ProposedMaximumConcentration
ActualConcentration
Lead (Pb) 0,1% < 0,1%
Mercury (Hg) 0,1% < 0,1%
Cadmium (Cd) 0,01% < 0,01%
Hexavalent Chromium (Cr6+) 0,1% < 0,1%
Polybrominated biphenyls (PBB) 0,1% < 0,1%
Polybrominated diphenyl ethers (PBDE) 0,1% < 0,1%
Certain components of products as stated above are exempted under the Annex of the RoHS
Directives as noted below:
Examples of exempted components are:
1. Mercury in compact uorescent lamps not exceeding 5 mg per lamp and in other lamps not
specically mentioned in the Annex of RoHS Directive.
2. Lead in glass of cathode ray tubes, electronic components, uorescent tubes, and electronic
ceramic parts (e.g. piezoelectronic devices).
3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight or
more lead).
4. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium
containing up to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by
weight.
ViewSonic EP1020r/EP1021r v
CopyrightInformation
Copyright © ViewSonic® Corporation, 2010. All rights reserved.
ViewSonic®, the three birds logo, OnView®, ViewMatch™, and ViewMeter® are registered
trademarks of ViewSonic® Corporation.
Disclaimer: ViewSonic® Corporation shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or consequential damages resulting from
furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic® Corporation reserves the right to
change product specications without notice. Information in this document may change without
notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any
purpose without prior written permission from ViewSonic® Corporation.
ProductRegistration
To meet your future needs, and to receive any additional product information as it becomes
available, please register your product on the Internet at: www.viewsonic.com.
ForYourRecords
ProductName:
ModelNumber:
DocumentNumber:
SerialNumber:
PurchaseDate:
EP1020r/EP1021r
ViewSonic Multimedia Digital Poster
VS13489
EP1020r/EP1021r_UG_ENG Rev. 1A 07-16-10
Productdisposalatendofproductlife
The lamp in this product contains mercury. Please dispose of in accordance with local, state or
federal laws.
ViewSonic® is concerned about the preservation of our environment. Please dispose of this
product properly at the end of its useful life. Your local waste disposal company may provide
information about proper disposal.
ViewSonic EP1020r/EP1021r 1
Contents
1. Introduction 1
1.1. Hardware features 1
1.2. Software Features 1
1.3. Package Contents 2
1.4. Physical ports and features 2
1.5. VESA mounting 2
2. Configuring the EP1020r/EP1021r 3
2.1. System Connections 3
2.2. USB keyboard Configuration Menus 3
2.3. Connect the EP1020r/EP1021r to your network 4
2.4. Clock and Calendar Settings 5
2.5. Brightness and Volume settings 5
2.6. Setting a password 6
2.7. Factory reset 6
2.8. Applying firmware upgrades 6
3. Content Management 7
4. Working with SMIL 8
4.1. Introduction 8
4.2. Playing a SMIL demo 8
4.3. www.a-smil.org for Developers 8
5. Technical Data 9
5.1. Specifications 9
6. Appendix: FAQ 10
ViewSonic EP1020r/EP1021r 1
1. Introduction
This document describes the hardware and software operations of the EP1020r/EP1021r, system set up, and
frequently asked questions.
1.1. Hardware features
•10.4-inch 4:3 LCD display and stereo speakers
•Built-in wireless b/g and Ethernet network
•Scala enabled for compatibility with Scala Content Manager
•Signage Manager Express configuration utility
•Content authoring via Microsoft PowerPoint (template-based slide show creation)
•Supports advanced device programming via the W3C SMIL open API
1.2. Software Features
Signage Manager Express utility for streamlined digital signage management
Signage Manager Express helps you quickly set up and test playback on your digital
signage player. Once you have scheduled your contents, you can quickly configure all
players across the network simultaneously with a few clicks of the mouse. Please see the
Signage Manager Express User's Manual for operation details.
Scala network enabled (Scala license required)
For industry leading network management, the EP1020r/EP1021r Digital ePoster is
certified to work in a Scala Content Manager networked environment. This provides
you with maximum flexibility in a reliable, RISC-based signage display.
SMIL Open API for developers
The EP1020r/EP1021r uses open XML-based scripting language for highly flexible
content presentation and playback control, so that your investments are never obsolete.
Using SMIL, the de facto language of multimedia communications, the player
understands the language adopted by professional development tools from Adobe,
Apple, Microsoft, Real Networks, and more.
EP1020r/EP1021r compatible with SignageLive and SignChannel application. Please key-in below
URL in the CONTENT SOURCE by USB keyboard. License does not include.
SignageLive : http://go.signagelive.com
SignChannel: http://rss.signchannel.com/productid=IAMP001/frameid={$player-id}/firmware=1.4.7
W3C
SMIL
Scala
Enabled
ViewSonic EP1020r/EP1021r 2
1.3. Package Contents
NOT INCLUDED: A USB keyboard is required for system setup
1.4. Physical ports and features
1.5. VESA mounting
The EP1020r/EP1021r provide MIS-D 75 VESA mounting
(75mmx75mm)
Main Unit Quick Start GuideAC Adapter Software CD
Stand Antenna
(EP1020r)
ViewSonic EP1020r/EP1021r 3
2. Configuring the EP1020r/EP1021r
2.1. System Connections
1 Attach the AC power adapter to power on the unit. The following progress bar will be displayed
on your monitor:
2 Player boot process takes approximately 90 seconds to complete. After boot up, the player will
indicate that it is ready for content sync via the USB port.
The player will boot into the “Open Standard Media
Player” screen. Plug in a USB keyboard to enter
configuration menus. The menu and blue
background will appear in about 30 seconds.
If you have already loaded media contents into
the player, contents will play back immediately after
boot up, and the “Open Standard Media Player”
screen will not be shown. You can still plug in a USB
keyboard at any time during playback to enter the
menu system.
2.2. USB keyboard Configuration Menus
You must attach a USB keyboard to the EP1020r/EP1021r to configure settings. With the player booted
up and ready, it takes approximately 30 seconds after you plug in the keyboard for the following menu
to be displayed:
Navigating the menus
Navigate the menus using arrow keys, space bar, enter key, ESC, and numeral keys on your USB
keyboard. Use the keyboard arrow keys to highlight menu items, press the space bar to move the star
(cursor), and then press enter to confirm (<OK>) or reject (<Cancel>) any changes.
~ 90 seconds
Andere Handbücher für EP1020r
2
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere ViewSonic Monitor Handbücher
ViewSonic
ViewSonic XG2705-2K Bedienungsanleitung
ViewSonic
ViewSonic VP191B - 19" LCD Monitor Bedienungsanleitung
ViewSonic
ViewSonic CDX4952 Bedienungsanleitung
ViewSonic
ViewSonic PD1213T Bedienungsanleitung
ViewSonic
ViewSonic VA2026W - 20" LCD Monitor Bedienungsanleitung
ViewSonic
ViewSonic VA2730-H Bedienungsanleitung
ViewSonic
ViewSonic UltraBrite A70f+ Bedienungsanleitung
ViewSonic
ViewSonic VA2703-LED Bedienungsanleitung
ViewSonic
ViewSonic VA2762-4K Bedienungsanleitung
ViewSonic
ViewSonic VA2709U-4K Bedienungsanleitung
ViewSonic
ViewSonic VG2457V Bedienungsanleitung
ViewSonic
ViewSonic VA912-1 Bedienungsanleitung
ViewSonic
ViewSonic VA2246-LED Bedienungsanleitung
ViewSonic
ViewSonic VPW4255 - 42" Plasma Panel Bedienungsanleitung
ViewSonic
ViewSonic VG3448 Bedienungsanleitung
ViewSonic
ViewSonic VA2406m-LED Bedienungsanleitung
ViewSonic
ViewSonic VA951S Bedienungsanleitung
ViewSonic
ViewSonic VG730M - 17" LCD Monitor Bedienungsanleitung
ViewSonic
ViewSonic A70f Bedienungsanleitung
ViewSonic
ViewSonic VA1716w - 17" LCD Monitor Bedienungsanleitung
