ViewSonic LS700-4KP Bedienungsanleitung

LS700-4KP

DLP Projector

User Guide

IMPORTANT: Please read this User Guide to obtain important information on installing

and using your product in a safe manner, as well as registering your product for future

service. Warranty information contained in this User Guide will describe your limited

coverage from ViewSonic Corporation, which is also found on our web site at http://

www.viewsonic.com in English, or in specic languages using the Regional selection

box in the upper right corner of our website. “Antes de operar su equipo lea cu

idadosamente las instrucciones en este manual”

Model No. VS17455

Compliance Information

FCC Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following

two conditions: (1) this device may not cause harmful interference, and (2) this device

must accept any interference received, including interference that may cause undesired

operation.

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency energy, and if not installed

and used in accordance with the instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference will not occur in a

particular installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more of the following

measures:

●Reorient or relocate the receiving antenna.

●Increase the separation between the equipment and receiver.

●Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

●Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modications not expressly approved by

the party responsible for compliance could void your authority to operate the equipment.

For Canada

CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

The device complies with the EMC Directive 2014/30/EU and Low Voltage

Directive 2014/35/EU.

Following information is only for EU-member states:

The mark is in compliance with the Waste Electrical and Electronic

Equipment Directive 2012/19/EU (WEEE).

The mark indicates the requirement NOT to dispose the equipment

including any spent or discarded batteries or accumulators as unsorted

municipal waste, but use the return and collection systems available.

If the batteries, accumulators and button cells included with this

equipment, display the chemical symbol Hg, Cd, or Pb, then it means

that the battery has a heavy metal content of more than 0.0005%

Mercury or more than, 0.002% Cadmium, or more than 0.004% Lead.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this unit near water.

6. Clean with a soft, dry cloth.

7. Do not block any ventilation openings. Install the unit in accordance with the

manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or

other devices (including ampliers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A

polarized plug has two blades with one wider than the other. A grounding type plug

has two blades and a third grounding prong. The wide blade and the third outlet,

consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs. Be

sure that the power outlet is located near the unit so that it is easily accessible.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specied by the

manufacturer, or sold with the unit. When a cart is used, use caution

when moving the cart/unit combination to avoid injury from tipping over.

13. Unplug this unit when unused for long periods of time.

14. Refer all servicing to qualied service personnel. Servicing is required when the

unit has been damaged in any way, such as: if the power-supply cord or plug is

damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed to

rain or moisture, or if the unit does not operate normally or has been dropped.

iii

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive

2011/65/EU of the European Parliament and the Council on restriction of the use of

certain hazardous substances in electrical and electronic equipment (RoHS2 Directive)

and is deemed to comply with the maximum concentration values issued by the

European Technical Adaptation Committee (TAC) as shown below:

Substance Proposed Maximum

Concentration

Actual Concentration

Lead (Pb) 0.1% < 0.1%

Mercury (Hg) 0.1% < 0.1%

Cadmium (Cd) 0.01% < 0.01%

Hexavalent Chromium (Cr6+) 0.1% < 0.1%

Polybrominated biphenyls (PBB) 0.1% < 0.1%

Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

Bis (2-ethylhexyl) phthalate (DEHP) 0.1% < 0.1%

Butyl benzyl phthalate (BBP) 0.1% < 0.1%

Dibutyl phthalate (DBP) 0.1% < 0.1%

Diisobutyl phthalate (DIBP) 0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex III of

the RoHS2 Directives as noted below:

Examples of exempted components are:

1. Lead in glass of cathode ray tubes.

2. Lead in glass of uorescent tubes not exceeding 0.2% by weight.

3. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.

4. Copper alloy containing up to 4% lead by weight.

5. Lead in high melting temperature type solders (i.e. lead-based alloys containing

85% by weight or more lead).

6. Electrical and electronic components containing lead in a glass or ceramic other

than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or

ceramic matrix compound.

Macintosh and Power Macintosh are registered trademarks of Apple Inc.

Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of

Microsoft Corporation in the United States and other countries.

ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered

trademarks of ViewSonic Corporation.

VESA is a registered trademark of the Video Electronics Standards Association.

DPMS and DDC are trademarks of VESA.

PS/2, VGA and XGA are registered trademarks of International Business Machines

Corporation.

Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or

omissions contained herein; nor for incidental or consequential damages resulting from

furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves the

right to change product specications without notice, Information in this document may

change without notice.

No part of this document may be copied, reproduced, or transmitted by any means, for

any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To fulll possible future product needs, and to receive additional product information as

it becomes available, please visit your region section on ViewSonic’s website to register

your product online.

Registering your product will best prepare you for future customer service needs.

Please print this user guide and ll the information in the “For Your Records” section.

For additional information, please see the “Customer Support” section in this guide.

For Your Records

Product Name: LS700-4KP

ViewSonic DLP Projector

Model Number: VS17455

Document Number: LS700-4KP_UG_ENG Rev.1A

Serial Number: ________________________________________________

Purchase Date: ________________________________________________

Product disposal at end of product life

The lightsource in this product contains mercury which can be dangerous to you and the

environment. Please use care and dispose of in accordance with local, state or federal

laws.

ViewSonic respects the environment and is committed to working and living green.

Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic’s

website to learn more.

USA & Canada: http://www.viewsonic.com/company/green/recycle-program/

Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/

Taiwan: http://recycle.epa.gov.tw/

Table of Contents

Key safety instructions.... 1

Introduction....................... 3

Projector features ...................................... 3

Shipping contents...................................... 4

External appearance of the projector ........ 5

Device control and functions ..................... 6

Projector Positioning ..... 11

Choosing a location..................................11

Projection Dimension............................... 12

Connection...................... 13

Connect to the computer or monitor........ 14

Connecting to Video source devices ....... 15

Connecting to HDMI devices................... 16

Connecting to composite video source

devices .................................................... 16

Audio playback with the projector............ 16

Operation......................... 17

Activate the projector............................... 17

Using the menus...................................... 18

Use basic settings ................................... 19

Use Network setting ................................ 20

Use Advanced settings............................ 21

Use Information ....................................... 22

Use Firmware upgrade............................ 23

Use Image settings.................................. 24

Use Advanced settings (in signal source

mode) ...................................................... 25

Switching input signal.............................. 26

Changing HDMI input settings................. 27

Adjusting the projected image ................. 28

Perform keystone correction.................... 29

Using the CEC function ........................... 30

Smart energy-saving ............................... 30

Light Source Mode .................................. 31

Operations at high altitudes..................... 31

Hiding the image...................................... 31

Optimize images in user mode................ 32

Fine-tuning of image quality in user

modes...................................................... 33

Adjust Gamma......................................... 34

Color Management.................................. 35

Fine-tuning of image in user modes ........ 36

Select the aspect ratio............................. 37

About the aspect ratio.............................. 37

Control the projector with the web

browser.................................................... 40

About Crestron e-Control®....................... 43

Using the projector under standby

mode........................................................ 45

Switch off the projector............................ 46

Menu operations...................................... 47

Maintenance.................... 53

Care of the projector................................ 53

LED Indicator........................................... 54

Troubleshooting ............. 55

Specications ................. 56

Projector specications............................ 56

Fuse specications.................................. 56

Dimensions.............................................. 57

Ceiling mount installation......................... 57

Timing chart............................................. 58

Disclaimer................................................ 62

Appendix ......................... 63

IR control table ........................................ 63

Address Code.......................................... 64

RS232 command table............................ 65

Key safety instructions

Design and testing of your projector have been carried out in compliance with the

latest safety standards for information technology (IT) devices. However, it is extremely

important for you to follow the instructions provided in this manual and product labels

during use to ensure user safety.

Safety Instructions

●Please read through this manual before using the projector. Save it for future

reference.

●Do not look straight at the projector lens during operation. The intense light

beam may damage your eyes.

●Refer servicing to qualied service personnel.

●Always open the lens shutter or remove the lens cap when the projector light

source has been switched on.

●In some areas there may be line voltage instability. This projector is designed to

operate safely within a mains voltage between 100 to 240 volts AC, but could fail if

power cuts or surges of ±10 volts occur. In areas where the mains voltage may

uctuate or cut out, it is recommended that you connect your projector through

a power stabilizer, surge protector or uninterruptible power supply (UPS).

●Do not block the projection lens with any objects when the projector is under

operation as this could cause the objects to become heated and deformed or even

cause a re.

●Do not place the projector on an unstable cart, stand, or cable. The product may fall

and sustain serious damage.

●Do not attempt to disassemble this projector. The projector contains high voltage

parts that may cause electrocution or death when it comes in contact with the human

body. Under no circumstances should you ever undo or remove any other covers.

Refer servicing to qualied service personnel.

●Do not place this projector in any of the following environments.

- Space that is poorly ventilated or conned. Allow at least 50 cm clearance from

walls and ensure free ow of air around the projector.

- Locations where temperatures may become excessively high, such as the inside of

a car with all windows rolled up.

- Locations that are too humid, dusty, or smoky may contaminate optical

components, shortening the projector's life span and darkening the image.

- Locations near re alarms

- Locations where temperature exceeds 40°C/104°F.

- Locations with altitudes greater than 5,000 m (16,500 feet).

●Do not block the ventilation holes. If the ventilation holes are seriously obstructed,

overheating inside the projector may result in a re.

- Do not place this projector on a blanket, bedding or any other soft surface.

- Do not cover this projector with a cloth or any other item.

- Do not place ammable items near the projector.

●Do not step on the projector or place any objects upon it. These acts may damage the

projector itself as well as cause accidents or personal injury.

●Do not place liquids near or on the projector. Liquids spilled into the projector may

cause damage. If the projector does become wet, please unplug the power cable

from the power socket and contact your local repair center for repairs.

●This product can be mounted on a ceiling suspension mount for back projection.

Use only ceiling suspension mounts that meet the relevant requirements and ensure that

the installation is safe.

●When the projector is under operation, you may sense some heated air and odor from

its ventilation grill. It is a normal phenomenon and not a product defect.

●Do not use the safety lever during transport or installation purposes. The safety lever

should only be used with the anti-theft cables sold on the market.

Safety instructions for ceiling mounting of the projector

We hope you to have a pleasant user experience with our projector. This is why we’re

bringing these safety reminders to your attention to prevent possible damage to person

and property.

If you intend to mount your projector on the ceiling, we strongly recommend that you use a

suitable projector ceiling mount kit and ensure it is securely and safely installed.

There may be safety risks if you fail to use an appropriate projector ceiling mounting kit.

Use of inappropriate connectors or screws of the wrong specications or length may cause

the projector to fall from the ceiling.

You can purchase a projector ceiling mounting kit from the projector dealer. We

recommend buying a safety harness in addition to the mounting kit. The harness should be

securely connected to the anti-theft locking groove on the projector as well as the base of

the ceiling mounting support. This will provide additional protection in case the connectors

of the mounting support becoming loose.

Like handling any bright light sources, do not directly look at the

light beam.

Introduction

Projector features

The projector integrates high-performance optical engine projection and a user-friendly

design to deliver high reliability and ease of use. The projector offers the following

features:

●The color mode provides different options designed for different projectors.

●Compatible with NTSC, PAL, SECAM and HDTV

●D-Sub 15-pin terminal can be connected to analog video

●Equipped with HDMI connection, supports HDCP

●Multi-language On-Screen Display (OSD) menus

●Digital keystone correction to correct distorted images

●RS-232 interface supports serial control

●The power saving mode reduces the lamp power consumption by up to 30% when no

input signal is detected for a set length of time.

●Presentation timer for better control of time during presentations

●3D Ready supported

●Color management can be used to adjust the color according to your preferences

●The screen type correction function can be projected on a variety of pre-set color

surfaces

●Switching among Normal, Power Saving and CUSTOM Modes reduces power

consumption.

●Quick Auto Search speeding up the signal detecting process

●Activating Power Saving mode will bring power consumption to below 0.5W

●“Network Settings” allows management on the projector state by using a remote

computer.

●One-key auto-adjustment to display the best picture quality (applicable to the analog

signal only)

●Provides Color Management adjustments for digital / video displays

Inhaltsverzeichnis

Andere ViewSonic Projektor Handbücher

ViewSonic

ViewSonic PJ551D - XGA DLP Projector Bedienungsanleitung

ViewSonic

ViewSonic PJ758 Bedienungsanleitung

ViewSonic

ViewSonic PJ556D Bedienungsanleitung

ViewSonic

ViewSonic PJL802 Bedienungsanleitung

ViewSonic

ViewSonic PJ755D - 2600 Lumens DLP Projector Bedienungsanleitung

ViewSonic

ViewSonic PJD5523w Bedienungsanleitung

ViewSonic

ViewSonic Precision Bedienungsanleitung

ViewSonic

ViewSonic PJ1158 - XGA LCD Projector Bedienungsanleitung

ViewSonic

ViewSonic PJD5132 Bedienungsanleitung

ViewSonic

ViewSonic Pro8600 Handbuch

ViewSonic

ViewSonic PJ750-2 Bedienungsanleitung

ViewSonic

ViewSonic Pro10 Series Bedienungsanleitung

ViewSonic

ViewSonic PJL6243 Bedienungsanleitung

ViewSonic

ViewSonic PJ562 - XGA LCD Projector Bedienungsanleitung

ViewSonic

ViewSonic PRO7827HD Bedienungsanleitung

ViewSonic

ViewSonic PJ656 - XGA Projector 6.2 Lbs Bedienungsanleitung

ViewSonic

ViewSonic ViewDock PJ258D Bedienungsanleitung

ViewSonic

ViewSonic PJ558D Bedienungsanleitung

ViewSonic

ViewSonic PJ260D - XGA DLP Projector Bedienungsanleitung

ViewSonic

ViewSonic PJ1173 - XGA LCD Projector Bedienungsanleitung

ViewSonic

ViewSonic PJL9371 Bedienungsanleitung

ViewSonic

ViewSonic M2W Bedienungsanleitung

ViewSonic

ViewSonic PJ256D - XGA DLP Projector Bedienungsanleitung

ViewSonic

ViewSonic M Series Bedienungsanleitung

Beliebte Projektor Handbücher anderer Marken

iEmmet

iEmmet MP-312 Bedienungsanleitung

Epson

Epson VS400 Bedienungsanleitung

Sony

Sony VPL-HS10 Marketing Specifications & Features Bedienungsanleitung

Sony

Sony VPL-HW65ES Service-Handbuch

Toshiba

Toshiba TLP-791U Bedienungsanleitung

Philips

Philips LC1341 Referenzhandbuch

Panasonic

Panasonic PTL735NTU - LCD PROJECTOR-NETWORK IB Bedienungsanleitung

NEC

NEC NP600S EDU Bedienungsanleitung

BenQ

BenQ SH753P Bedienungsanleitung

Eiki

Eiki EK-623U series Bedienungsanleitung

Epson

Epson PowerLite Pro Cinema 6020UB Bedienungsanleitung

Epson

Epson PowerLite Home Cinema 705HD Bedienungsanleitung

Christie

Christie LHD700 Bedienungsanleitung

Navitar

Navitar FX Bedienungsanleitung

InFocus

InFocus LitePro 560 Bedienungsanleitung

Sony

Sony SRX-R815P Bedienungsanleitung

Vivitar

Vivitar DP1500 X Bedienungsanleitung

Acer

Acer C20 Series Bedienungsanleitung