Vigitron Vi1004 Bedienungsanleitung
5. Troubleshooting
noituloSesuaCmelborP
No picture Connections are not
secure
Wrong pair of wires
Make sure the connections are secured
properly and wires are not broken or missing.
Verify that each video signal uses conductors
from the same twisted pair.
Scrambled picture Wrong polarity Check polarity on each pair of wires.
Make sure to match the corresponding
numbers on the detachable terminal block and
BNC connectors
Picture is unstable
and has ghost
effect
Long stubs The transceiver devices must be used with
point to point connection of unshielded twisted
pair wires. Remove any extra branch of twisted
pair wires. Verify that there are no star
configurations.
Noisy picture Untwisted pair of wires Use twisted pair wires to avoid interference.
Dim picture Long wires
High gauge wires.
Use less than 6 feet of coax cable between the
transceiver device and the video source. UTP
less 1000 ft.
Wire gauge must be 24 or better.
Low quality or
blurred picture
Shielded wires Use unshielded twisted pair wires Cat 2-7 to
avoid impedance mismatch.
6. Warranty
Subject to the provisions described below, Vigitron, Inc. UTP Passive Hub VI1004 (“Product”) is protected by
a limited lifetime warranty from the date of purchase from defects in material and workmanship.
Should this product fail to perform as described above within ten years following the original date of purchase,
Vigitron, Inc. will ship a replacement for the failed product upon return of the defective product.
This warranty does not apply if, in the judgment of Vigitron, Inc., Product fails due to damage from shipment,
handling, storage, accident, abuse or misuse, or if it has been used or maintained in a manner not conforming
to Product manual instructions, has been modified in any way, or has had any serial number removed or
defaced. Repair by anyone other than Vigitron, Inc. or an approved agent will void this warranty. The
maximum liability of Vigitron, Inc. under this warranty is limited to the purchase price of the Product covered
by the warranty.
Prior to returning any defective Product, the end customer or the reseller from whom the end customer
originally purchased the Product must obtain a Return Materials Authorization (RMA) number from Vigitron,
Inc. All defective Products should be returned to Vigitron, Inc. with shipping charges prepaid.
Vigitron, Inc. will not accept collect shipments.
Except as specifically provided in this agreement or as required by law, the warranties and remedies
stated above are exclusive and in lieu of all others, oral or written, expressed or implied. Any and all
other warranties, including implied warranties of merchantability, fitness for a particular purpose and
non-infringement of third party rights are expressly excluded. Vigitron,Inc. shall not under any
circumstances be liable to any person for any special incidental, indirect or consequential damages,
including, without limitation, damages resulting from use or malfunction of the products, loss of
profits or revenues or costs of replacement goods, even if Vigitron, Inc. is informed in advance of the
possibility of such damages.
VIGITRON, Inc.
7810 Trade Street, Suite 100
San Diego, CA 92121, U.S.A.
Phone:(858) 484-5209 Fax:(858) 484-1205
www.vigitron.com
MODEL Vi1004
PASSIVE 4-PORT
UTP TRANSCEIVER HUB
USER’S MANUAL
VIGITRON, INC.
7810 Trade Street, Suite 100
San Diego, CA 92121, U.S.A.
Phone: (858) 484-5209
Fax: (858) 484-1205
1. Introduction
The Vigitron Vi1004 is a passive 4-port hub that transmit or receive video or
data over unshielded twisted pair (UTP) wires, point-to-point, for distances up
to 1000 feet* (330 m). It also provides support for the “up the coax” PTZ
control signals.
This hub uses Category 2-7 twisted pair wires, is easy to install, cost
effective, and does not require power. It has built-in surge suppression to
protect video equipment against damaging voltage spikes. Its cross-talk and
noise immunity ensures quality video signals. The Vigitron passive hubs offer
quality video in a highly integrated and a cost-effective package. This HUB is
ideal for a wide variety of security and surveillance applications that require
medium-density CCTV systems.
2. Mating Model Numbers and Features:
Model # Surge
Protect. Ground
Lifting Distance
(feet) Ground
Lifting Mating Model #
No 1000* No VB1000, Vi1001
Vi1004, Vi1008, Vi1016, Vi1032
Vi1004 Yes Yes 3000 Yes Vi6100VR, VI6104, Vi6008,
Vi6116, Vi6132
3. Specifications**
Video Format NTSC, PAL, and SECAM
Frequency DC to 6 MHz
Coax 75 Ohm
Twisted Pair 100 Ohms +/- 20%, 24 AWG min,
Up to 1000 feet* (330 m) Unshielded Category 2-5
Insertion Loss 0.3 dB
CMRR 50 dB
Power No power required
Connectors UTP: UTP: Detachable Terminal Blocks and RJ-45
Video: Female BNC
Ground: Screw terminal
Temperature Operating: -10C to +70C, Storage: -30C to +70C
Humidity 0 to 95%, non-condensing
Transient Immunity 6000V, 1.2 usec x 50 usec
Material Black ABS Plastic, UL rating of 94V-0
Dimensions 0.90x2.19x4.88 Inches, 2.3x5.6x12.4 cm (HxWxL)
Weight 0.2 Lb, 100 g
Mounting Philips Screws or VI0010 Rack-Mounting Kit (not Included)
* It is recommended not to exceed 750 feet (250 m) when using Digital Video Recorders.
**Specifications subject to change without notice.
4. Installation
4.1 Preparation:
Before getting started verify that you have the following items:
•Unshielded Twisted Pair (UTP) wires (24 AWG or better). Do not use untwisted wires since
it may result in interference and noisy picture. Do not use shielded twisted pair wires since
it may cause impedance mismatch.
•Verify that each video signal uses conductors from the same twisted pair.
•The transceiver devices must be used with point-to-point connection of unshielded twisted
pair wires. Any extra branch of twisted pair will cause ghost effect and poor quality video.
•Do not use more than 6 feet of coax cable between the transceiver devices and video
sources.
4.2 Transmitter side installation:
1. Choose the right mating transceivers (See table in section 2).
2. When a single transceiver is used, connect the video source (camera, etc.) through a coax
cable (less than 6 feet) or directly to the BNC video input of each transceiver. Connect one
end of the UTP wire to the terminal block of each transceiver. Connect the green GND wire
to chassis ground.
3. When a transceiver hub (i.e, Vi1004) is used, connect the video source (camera, etc.)
through a coax cable or directly to the BNC video input of each channel. Connect one end
of the UTP wire to the terminal block of the corresponding channel.
4.3 Receiver side installation:
1. Mount the hub near the monitors or DVRs using the VI0010 rack mount panel or by itself.
2. Connect the hub to the video equipment (monitors, VCRs, etc.) using the 2 feet coax
cables provided with the kit. Make sure the connections are secured properly.
3. Connect the other end of the UTP wire, to the hub’s detachable terminal block. Make sure
to match the corresponding numbers on the detachable terminal block and BNC
connectors.
4. If the picture is scrambled change the polarity of the twisted pair wires to the corresponding
terminal block.
1423
VI6004HR UTP Receiver
Vi1004 UTP Transceiver
1423
12 431234
1234
The Vi1004 Top View
Inhaltsverzeichnis
Andere Vigitron Transceiver Handbücher
