Viking Range 7 Series Bedienungsanleitung
Installation Guide
Rear Trim/Curb Base Accessories
7 Series Ranges/Rangetops
2
Rear Trim Accessories
ATTACHING REAR TRIM
(Island Trim, 10” H. Backguard OR 24” H. High Shelf Back Panel)
1. Remove the grate supports in order to locate the rear flange
and mounting stud on the unit. Grasp the rear trim on each end
and carefully align the rear trim over the rear flange and insert
mounting screw into keyhole opening on the rear trim.
Make sure the rear trim is in front of the sealed burner
box and not behind.
2. Align holes in rear trim with holes in flange. Slide
rear trim down until it rest on top of the side panels
ensuring accessory rear wall is outside of unit. Secure
with enclosed #10 x 1/2” (1.3 cm) phillips head
threaded screws. 36” W. ranges/rangetops have (3)
hole locations and 48” W ranges/rangetops have (4).
To reduce the risk of fire or injury to persons, check to
make sure all packaging has been removed from the
outside and inside parts of the rear trim device before
installing. MAKE SURE ALL CORRUGATED MATERIAL IS
REMOVED FROM INSIDE THE HIGH SHELF.
WARNING
Remove
grates
SIDE VIEW REAR VIEW
Keyhole
opening
Mounting
screw
Rear flange
Side Panel
To reduce the risk of injury, assistance from a
second person is recommended when installing
48” backguards or high shelf backs.
CAUTION
3
Rear Trim Accessories
IMPORTANT: USE OF ISLAND TRIM WITH AND WITHOUT 6” (15.2 CM) REAR CLEARANCE.
Normal installation for island trim on either a range or rangetop is in an island/peninsula or where there is a minimum
clearance of 6”(15.2 cm) to any type of wall at the rear of the unit. Ranges and rangetops with an island trim installation
can be installed at zero clearance to the rear wall as long as the wall is non-combustible. The responsibility for ensuring
that the rear wall is non-combustible and heat resistant lies with the individual owner and/or end user. Only in those
cases where the island trim is installed with 6” (15.2 cm) of minimum clearance to a rear wall, or when a truly non-
combustible material is used, will the warranty apply. In no case will Viking Range, LLC accept responsibility for any
claims which may result from heat damage against a rear wall, including cosmetic damage. It is the total responsibility of
the owner/end user to ensure that the material utilized in such applications is not only non-combustible, but is also truly
heat-resistant.
24” H. High Shelf
After installing the high shelf back panel on the range/
rangetop, place the top rolled edge on the shelf (X) over the
front lip of the high shelf back panel. Secure with the (4)
enclosed #10 -24x 1/2” (1.3 cm) PH machine screws
X
Screw locations
(two on each side underneath shelf)
Regulator
Screw
Locations
NOTE: Regulator will be visible after rear trim
accessory is installed.
4
COUNTERTOP REAR TRIM
1. Locate screw hole openings (A) on the back of the island trim near the top.
2. Align screw hole openings on the countertop rear trim with the ones on the back of the island trim.
3. Attach rear trim to island trim with enclosed #10 x 1/2” (1.3 cm) PH Tek screws.
A
Rear Trim Accessories
5
Curb Base Accessories
STANDARD CURB BASE FRONT
1. The standard curb base front (A) is completely assembled.
2. Remove the assembly from the carton and simply clip onto the front range legs.
3. The assembly is adjustable about 2” (5.1 cm) front to back so that alignment with the cabinet toe front is possible.
Loosen bracket bolts on each side, but allow snug fit. Clip assembly onto range legs; determine front to back setting;
remove, tighten bolts, and reattach.
A
6
Curb Base Accessories
CUSTOM CURB BASE FRONT
1. Remove the standard curb base front assembly from the carton.
2. Remove the front (A) from the mounting assembly (B).
3. Attach locally supplied front (C) to the mounting assembly (B) and simply clip onto the front range legs.
Important Note: The locally supplied front must not be any taller than 3-1/8” (7.9 cm) tall. Fronts taller than 3-1/8” (7.9
cm) could obstruct the airflow.
4. The assembly is adjustable about 2” (5.1 cm) front to back so that alignment with the cabinet toe front is possible.
Loosen bracket bolts on each side, but allow snug fit. Clip assembly onto range legs; determine front to back setting;
remove, tighten bolts, and reattach.
Important Note: The range must be installed as specified in the range installation guide for proper airflow when using
the custom curb base.
B
C
7
Viking Range, LLC
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-(845-4641)
or visit the Viking Web site at vikingrange.com in the U.S. or brigade.ca in Canada.
F21412 EN (083114)
Inhaltsverzeichnis
Andere Viking Range Reichweite Handbücher
Viking Range
Viking Range VGR736 Bedienungsanleitung
Viking Range
Viking Range VERT301-4B Bedienungsanleitung
Viking Range
Viking Range CVRT530 Bedienungsanleitung
Viking Range
Viking Range VGR7362 Bedienungsanleitung
Viking Range
Viking Range VESC530-4B Bedienungsanleitung
Viking Range
Viking Range 30" W. Models Bedienungsanleitung
Viking Range
Viking Range Professional Series Bedienungsanleitung
Viking Range
Viking Range Tuscany Series Bedienungsanleitung
Viking Range
Viking Range 5 Series VGC Bedienungsanleitung
Viking Range
Viking Range VDSC530 Bedienungsanleitung
Viking Range
Viking Range VGR5304B Bedienungsanleitung
Viking Range
Viking Range VGIC5302 Bedienungsanleitung
Viking Range
Viking Range CVGR5304B Bedienungsanleitung
Viking Range
Viking Range 5 Series VGC Bedienungsanleitung
Viking Range
Viking Range VGRT736 Bedienungsanleitung
Viking Range
Viking Range CVGIC5301 Bedienungsanleitung
Viking Range
Viking Range 5 Series VGC Bedienungsanleitung
Viking Range
Viking Range RVER3301 Bedienungsanleitung
Viking Range
Viking Range TVDR3604B Bedienungsanleitung
Viking Range
Viking Range 5 Series VGC Bedienungsanleitung
