Viking DMOS201 Series Bedienungsanleitung

Viking Installation Guide

Designer Microwave Built-In Trim Kit

Table of Contents

IMPORTANT–Please Read and Follow!

Warnings & Important Information ———————————————————————— 2

Speciﬁcations ————————————————————————————————— 3

General Information——————————————————————————————— 4

Parts Included in the Kit ————————————————————————— 4

Cabinet or Wall Cutout —————————————————————————— 4

Electrical Outlet Location ————————————————————————— 4

Installation ——————————————————————————————————— 5

Mounting Template ——————————————————————————— 5

Bottom Duct Assembly—————————————————————————— 6

Mounting Bracket Assembly ——————————————————————— 6

Cabinet Installation ——————————————————————————— 7

Frame Assembly————————————————————————————— 7

Side Decoration Assembly (For Surface Mount Only) ————————————— 8

Over Oven Installation —————————————————————————— 8

Performance Checklist ————————————————————————————— 8

Before beginning, please read theseUÊ

instructions completely and carefully.

Be sure to DISCONNECT THE PLUG of theUÊ

microwave oven from the electrical outlet

before installing the built-in trim kit. Remove

the turntable from the oven cavity.

Because the kit includes metal parts, cautionUÊ

should be used in handling and installation

to avoid the possibility of injury.

Do not remove permanently afﬁxed labels,UÊ

warnings, or plates from the product. This

may void the warranty.

Please observe all local and national codesUÊ

and ordinances.

The installer should leave these instructionsUÊ

with the consumer who should retain for local

inspector’s use and for future reference.

WARNING

This built-in trim kit is designed for use ONLY

with Viking microwave ovens specifying built-

in trim kit DMTK302 on the rating label on the

left side wall of the oven cavity.

Microwave Oven Built-In Trim Kit

DMOS201 DMTK302

Overall Width 24" (60.9 cm) 29-1/2" (74.9 cm)

Overall Height from Bottom 13-3/8" (33.9 cm) 17-1/2" (43.7 cm)

Overall Depth from Rear 19-1/8" (48.7 cm) NA

Oven Interior Width

Height

Depth

Overall

17-3/8"

10-1/2"

18-5/8"

2.0 cu. ft.

(44.1 cm)

(26.6 cm)

(47.3 cm)

Electrical Requirements 120VAC/60 Hz NA

Max. Amp Usage 1.5 KW 13 amps NA

Approx. Shipping Wt. 46 lbs. (20.9 kg) 15 lbs. (6.9 kg)

The International Electrotechnical Commission’s standardized method for measuring output*

wattage. This test method is widely recognized.

In compliance with standards set by:

FCC – Federal Communications Commission Authorized.

DHHS – Complies with Department of Health and Human Services (DHHS) rule, CFR, Title 21,

Chapter I, Subchapter J.

– This symbol on the Rating label means the product is listed by Underwriters

Laboratories, Inc. for use in USA or Canada.

Specifications

General Information

14-1/4" (361.95 mm)

Minimum Cutout OpeningWidth 27-3/4" (704.9 mm)

Minimum Cutout Opening Height 16-9/16" (420.7 mm)

Maximum Cutout Opening Height 16-13/16" (427 mm)

Maximum Cutout OpeningWidth 28" (711.2 mm)

Distance between holes 9.1" (231.2 mm)

14" (355.6 mm)

Center Line

Floor Line of Cutout Opening

BUILT-IN TRIM KIT

SURFACE MOUNTING TEMPLATE

FOR DESIGNER SERIES MICROWAVEOVEN

1. Align the Surface Mounting Template center line with the

centerof the cabinet. Align the Floor Line with the bottom

ofthe cabinet at the desired height. Tape it into place.

2. Predrill 4 holes marked with a 5RQE" drill bit.

3. Cut the cabinet opening between the minimum and

maximumcutout opening lines. Be careful to cut precisely

alongthe Floor Line of the cutout.

4. Remove template from the cabinet.

3-15/16" (100 mm)



4-3/16" (106.4 mm)

FLOOR LINE OF CUTOUT OPENING

BUILT-IN TRIM KIT

FLUSH MOUNTING TEMPLATE

FOR DESIGNER SERIES MICROWAVE OVEN

CABINET CUTOUT LINE

CENTER LINE

SIDE SPACER TEMPLATE - L

SIDE SPACER TEMPLATE - R

FIGURE 1

CutoutOpening Height 17-5/16" (439.8 mm)

CABINET CUTOUT LINE

FIGURE 3

14" (355.9 mm)

Distancebetween holes 9.1" (231.2 mm)

Cutout Opening Width 29-5/8" (752.5 mm)

14-13/16" (376.2 mm)

FIGURE 2





1) Frame Assembly: QTY 1 2) Bottom Duct Assembly: QTY 1

3) Mouting Bracket: QTY 2 4) SIDE DECORATION: QTY 2

(SURFACE MOUNTING ONLY)



1) Frame Assembly: QTY 1 2) Bottom Duct Assembly: QTY 1

3) Mouting Bracket: QTY 2 4) SIDE DECORATION: QTY 2

(SURFACE MOUNTING ONLY)



1) Frame Assembly: QTY 1 2) Bottom Duct Assembly: QTY 1

3) Mouting Bracket: QTY 2 4) SIDE DECORATION: QTY 2

(SURFACE MOUNTING ONLY)



1) Frame Assembly: QTY 1 2) Bottom Duct Assembly: QTY 1

3) Mouting Bracket: QTY 2 4) SIDE DECORATION: QTY 2

(SURFACE MOUNTING ONLY)





Parts Included in the Kit

Item Part Name QTY

Frame Assembly 1

Bottom Duct 1

Mounting Bracket 2

Screw A :1-3/16" length 2

Screw B: 1-3/4" length 4

Side Decoration

(Surface Mount Only)

Surface Mounting Template 1

Flush Mounting Template 1

Electrical Outlet Location

CAUTION

Outlet should NOT be in the shaded area as

indicated on ﬁgure .



figure

4"(10.2 cm)

6"(15.2 cm)

NOTES:

If the Depth (C) dimension is greater than 21"UÊ

(53.3 cm), the outlet location may be in any

area on the rear wall.

The ﬂoor of the opening should be constructedUÊ

ofplywood strong enoughtosupport the weight

of the oven and ﬂoor load (approximately 100

pounds). The ﬂoor should be level for proper

operation of the oven. Be sure to check the

local building code as it may require that the

opening be enclosed with side, ceiling and rear

partition. The proper functioning of the oven

does not require the enclosure.

Cabinet or Wall Cutout

Cutout Dimensions Flush

Mount

Surface

Mount

Height Minimum 17-5/16"

(439.8mm)

16-9/16"

(420.7mm)

Maximum N/A 16-13/16"

(427mm)

Width Minimum 29-5/8"

(752.5mm)

27-3/4"

(704.9mm)

Maximum N/A 28"

(711.2mm)

Depth !Minimum 20"

(503mm)

20"

(503mm)

13/16" min.

15/16" max.

13-1/2" min.

24" min. width

27-7/8" max. width

1-9/16" (39.7 mm)

BOTTOM and SIDE

SPACER (R and L) offset

EDGES TO ALIGN SIDE SPACER

TEMPLATES (R and L)

Side Spacer (L) Side Spacer (R)

BOTTOM SPACER

CENTERED with

CABINET CUTOUT



figure



SIDE SPACER—2

REQUIRED. Must

protrude from edge of

cabinet cutout towards

center as shown.

BOTTOM SPACER—1

REQUIRED. 1/4" plywood.

For FLUSH MOUNT, two (2) side spacers and one (1) bottom

spacer are required. Spacers are not included in the kit and

must be fabricated by installer. See ﬁgures 3



and

for

spacer requirements. Make sure that all three spacers are

offset from the front of the cabinet by 1-9/16".

Cut out the Side Spacer Templates (R and L)

from the Flush Mounting Template. Align the

indicated edges to the corresponding right and

left side spacers as shown in ﬁgure . Make sure

to align the bottom edges of the side spacer

templates to the ﬂoor of the cabinet opening.

Predrill two (2) holes marked “A” on Side Spacer

Template – R and two (2) holes marked “B” on

Side Spacer Template – L with 1/16" drill bit.

Remove templates from the cabinet.

Installation

Mounting Template

Determine which mounting method to use

based on the required conﬁguration. See ﬁgure

A for FLUSH MOUNT and B for SURFACE

MOUNT.

Align the template corresponding to the required

mounting method to the center of the cabinet.

Make sure that the template is level with the

ﬂoor. Tape it into place. Cut the cabinet opening

along the lines speciﬁed on the template. Leave

template taped in place.

For SURFACE MOUNT, predrill 4 holes marked “A” with a

1/16" drill bit. Remove template from the cabinet. Go to

Bottom Duct Assembly.



figure



FLUSH MOUNT CONFIGURATION—

Microwave Oven and Frame Assembly glass

are ﬂush with the cabinet.

SURFACE MOUNT CONFIGURATION

—Microwave Oven and Frame Assembly

protrude from the surface of the cabinet.

b. Surface Mount Configuration -

Microwave Oven and Frame Assembly

protrude from the surface of the cabinet.

Illustration 2

a. Flush Mount Configuration -

Microwave Oven and Frame Assembly

glass are flush with the cabinet

Indicated surfaces are ﬂush.

Installation

Bottom Duct Assembly



figure

CENTER THE

BOTTOM DUCT

Illustration 6 - for Flush Mount

SCREW A

BOTTOM DUCT

MAKE BOTTOM

FLANGE FLUSH WITH

BOTTOM SPACER

Place the Bottom Duct in the cabinet opening. For FLUSH

MOUNT, it will rest on the bottom spacer centered with

the cabinet. See ﬁgure .



figure

Illustration 7 - for Surface Mount

CENTER THE

BOTTOM DUCT

SCREW A

BOTTOM DUCT

MAKE BOTTOM FLANGE

FLUSH WITH CABINET

For SURFACE MOUNT, the Bottom Duct will rest on the

ﬂoor of the opening. See ﬁgure .

Align the Bottom Duct to the center of the

opening with the bottom ﬂange securely ﬂush

with the bottom spacer (for FLUSH MOUNT) or

the cabinet (for SURFACE MOUNT).

Secure the Bottom Duct Assembly with the

two (2) SCREWS A. See figures and 

respectively.

Mounting Bracket Assembly

Position the mounting brackets to align with the

predrilled holes that were drilled with the mounting

template.

SCREW B



FLUSH MOUNT BRACKET

figure



SURFACE MOUNT BRACKET

The enclosed ends of the mounting brackets should face

inwards. Check that they are vertical and then secure loosely

with four (4) Screws B. See Figure .

figure



27-1/2"

(698.5mm)

EQ. EQ.

Installation

Align the mounting brackets horizontally by

sliding them back and forth along the screw

slots until the brackets are exactly 27-1/2" apart

and equal distance from the cabinet sides. See

ﬁgure .

Once the brackets are correctly positioned,

securely tighten the four (4) screws B.

Cabinet Installation

Place the oven adjacent to the wall or cabinet

opening. Plug the power cord into the electrical

outlet.

CABINET INSTALL FRAME INSTALL CABINET INSTALL

figure



Carefully guide the assembled oven into the prepared

opening. Slide the oven onto the Bottom Duct Assembly.

See ﬁgure .

figure



CABINET INSTALL FRAME INSTALL CABINET INSTALL

BOTTOM

DUCT

ASSEMBLY

FOOT

DUCT RECESS

Avoid pinching the cord between the oven and the wall.

Adjust the position of the oven so that the feet of the oven

are ﬁtted into the recesses of the Bottom Duct Assembly.

ee ﬁgure .

Frame Assembly

Turn over FRAME ASSEMBLY to locate the 4

ball studs.

SNAP ATTACHMENT LOCATIONS ON

MOUNTING BRACKETS

SMALL STAINLESS DECORATIONS ON TOP

BALL STUD BACK OF FRAME ASSEMBLY

figure



Position the FRAME ASSEMBLY with the small

stainless decorations on top. Align the 4 ball

studs with the 4 snap attachments at both ends

of the MOUNTING BRACKETS.

Secure the FRAME ASSEMBLY by ﬁrmly pushing

it onto the Mounting Brackets engaging the four

(4) snap attachments. See Figure .

F20722 EN (CC082407J)

TINSLB005MRR0

Viking Range Corporation

111 Front Street

Greenwood, Mississippi 38930 USA

(662) 455-1200

For product information

call 1-888-VIKING1 (845-4641)

or visit the Viking Web site at

vikingrange.com

Over Oven Installation

figure

2" (5.1 CM) FOR 30" W LOWER OVEN

Performance Checklist

Make sure the unit has been installed1.

according to all of the Installation Instructions

and the required Mounting Template.

Plug in the power cord.2.

Keep the Use & Care Manual and Installation3.

Manual.

Installation

Side Decoration Assembly

(For Surface Mount Only)

ALIGN TOP

SURFACE OF SIDE

DECORATION TO

TOP SURFACE OF

FRAME ASSEMBLY

FRONT INNER EDGE OF

SIDE DECORATION

FRONT SIDE EDGE OF FRAME ASSEMBLY

figure

Peel the backing off the tape on the backside of

the SIDE DECORATIONS. Align the front inner

edge of the side decorations to the front side

edge of the FRAME ASSEMBLY.

Align the top surface of the side decorations

to the top surface of the FRAME ASSEMBLY.

Secure the side decorations by pressing them

ﬁrmly against the side of the FRAME ASSEMBLY.

See Figure ".

Andere Handbücher für DMOS201 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Viking Mikrowellenofen Handbücher

Viking

Viking RVMH330 Bedienungsanleitung

Viking

Viking Built-In Gebrauchsanweisung

Viking

Viking RVM320 Bedienungsanleitung

Viking

Viking VMOS200AL Bedienungsanleitung

Viking

Viking Designer Select DESO127 Bedienungsanleitung

Viking

Viking Professional VMOR205 Bedienungsanleitung

Viking

Viking Designer DMOR200SS Leitfaden

Viking

Viking Designer Microwave Built-In Trim Kit Bedienungsanleitung

Viking

Viking Designer DMOS200SS Bedienungsanleitung

Viking

Viking VMOS201SS Bedienungsanleitung

Viking

Viking VMOS201SS Bedienungsanleitung

Viking

Viking VMOC206SS Bedienungsanleitung

Viking

Viking DMOC205SS Bedienungsanleitung

Viking

Viking RVMHC330 Bedienungsanleitung

Viking

Viking VMOR506 Bedienungsanleitung

Viking

Viking VMOC506 Gebrauchsanweisung

Viking

Viking Designer DMOC205 Bedienungsanleitung

Viking

Viking Designer DMOS200 Bedienungsanleitung

Viking

Viking Professional VMOR205 Bedienungsanleitung

Viking

Viking VCSO210SS Bedienungsanleitung

Viking

Viking Designer DMOR205SS Bedienungsanleitung

Viking

Viking DrawerMicro Designer DMOD240SS Bedienungsanleitung

Viking

Viking Professional VMOD240 Bedienungsanleitung

Viking

Viking RVMH330 Bedienungsanleitung

Beliebte Mikrowellenofen Handbücher anderer Marken

Daewoo

Daewoo KOG-574R0S Bedienungsanleitung

LG MH7040SS Bedienungsanleitung

Sharp

Sharp R-895(AL)M Bedienungsanleitung

Dometic

Dometic DOTRM13W Bedienungsanleitung

Sanyo

Sanyo EM-X680 Bedienungsanleitung

Sharp

Sharp R-393M Bedienungsanleitung

KitchenAid

KitchenAid KMCX4510 Montageanleitung

Smeg

Smeg S45MCX1 Bedienungsanleitung

Russell Hobbs

Russell Hobbs RHM2044 Bedienungsanleitung

Sunbeam

Sunbeam SMW759 Bedienungsanleitung

Gallet

Gallet FMOE230S Bedienungsanleitung

Bosch

Bosch CEG732X.1B Bedienungsanleitung

Dometic

Dometic Roadmate 230 Bedienungsanleitung

Samsung

Samsung SJ0396W Bedienungsanleitung

Sanyo

Sanyo EM-P494WS Bedienungsanleitung

Sharp

Sharp R-240 Bedienungsanleitung

Electrolux

Electrolux EMS2840 Bedienungsanleitung

Daewoo

Daewoo KOC-984T2S13 Bedienungsanleitung