Viking Combination Beverage Center Technisches Handbuch

Viking Use/Installation Guide

Combination Beverage Center/

Ice Maker

Viking Range Corporation

111 Front Street

Greenwood, Mississippi 38930 USA

Retain for Future Reference

IMPORTANT - PLEASE READ AND FOLLOW

••Before beginning, please read these instructions completely and carefully.

• Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.

• Please observe all local and national codes and ordinances.

• Please ensure that this product is properly grounded.

• The installer should leave these instructions with the consumer who should retain for local inspector’s use and for

future reference.

TToorreedduucceetthheerriisskkooffffiirree,,eelleeccttrriiccaallsshhoocckk,,oorriinnjjuurryywwhheennuussiinnggyyoouurrccoommbbiinnaattiioonnbbeevveerraaggeecceenntteerr//iicceemmaakkeerr,,ffoollllooww

bbaassiiccpprreeccaauuttiioonnssiinncclluuddiinnggtthheeffoolllloowwiinngg::

•FOR YOUR SAFETY•

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR

ANY OTHER APPLIANCE. THE FUMES CAN CREATE A FIRE HAZARD OR EXPLOSION.

IIttiissyyoouurrrreessppoonnssiibbiilliittyyttoobbeessuurreeyyoouurrccoommbbiinnaattiioonnbbeevveerraaggeecceenntteerr//iicceemmaakkeerriiss::

•located so the front is not blocked to restrict incoming or discharge air flow.

•properly leveled.

•located in a well ventilated area.

•connected to the proper kind of outlet, with the correct electric supply and grounding. A 115 volt, 60 Hz, 15 amp

fused electrical supply is required. NNOOTTEE::Time delay fuse or circuit breaker is recommended.

•not used by anyone unable to operate it properly.

•used only for its intended purpose.

•properly maintained.

•SAVE THESE INSTRUCTIONS•

DANGER

WARNING

SUFFOCATION HAZARD

Remove doors from your old combination beverage center/ice maker.

Failure to do so can result in child entrapment, which can cause death

or brain damage.

IMPORTANT: Child entrapment and suffocation are not problems of the

past. Junked or abandoned combination beverage center/ice makers are

still dangerous, even if they will sit for “just a few days.” If you are getting

rid of your combination beverage center/ice maker, please follow the

instructions below to help prevent accidents.

BEFORE YOU THROW AWAY YOUR OLD REFRIGERATION PRODUCT:

•Take off the doors.

•Leave the shelves in place so that children may not easily climb inside.

PROPER DISPOSAL OF YOUR OLD REFRIGERATION PRODUCT

UNDERCOUNTER CABINET CUTOUT

*24” width for cabinet only. 24 1/4” (61.6 cm)

need for cabinet and door width clearance if

door is recessed between cabinets.

SPECIFICATIONS/DIMENSIONS

PROFESSIONAL SERIES

BBaassiiccEElleeccttrriiccDDaattaa

•115 VAC/60 Hz

•Maximum amps - 3.3

•Approximate Shipping Weight - 140 lbs. (63.2 kg)

Min. 34 1/4”

(87.0 cm)

Max 35”

(88.9 cm)

with leveling

legs fully

extended

30 3/4”

(78.1 cm)

23 7/8” (60.6 cm)

47 1/4” (120.0 cm)

22” (55.9 cm)

24 3/8” (61.9 cm)

26 7/8” (68.3 cm)

*Optional:

Cutout for electrical

outlet can be

placed in adjacent

cabinetry.

AA24” (61.0 cm)*

BBMin. 34 1/2” (87.6 cm)

Max. 35 1/8” (89.2 cm)

CC24” (61.0 cm)

SPECIFICATIONS/DIMENSIONS

DESIGNER SERIES

BBaassiiccEElleeccttrriiccDDaattaa

•115 VAC/60 Hz

•Maximum amps - 3.3

•Approximate shipping weight - 140 lbs (63.2 kg)

Front View

30 3/4”

(78.1 cm)

Mín.

34 1/4”

(87.0 cm)

Max.

35”

(88.9 cm)

with leveling

legs fully

extended

23 7/8” (60.6 cm)

Side View

22” (55.9 cm)

24 3/8” (61.9 cm)

25 3/8” ( 64.5 cm)

47 1/4” (120.0 cm)

AREA REQUIREMENTS

UUnniittssCCeerrttiiffiieeddffoorrIInnddoooorrUUssee--((bbllaacckkoouutteerrccaabbiinneett))

MUST BE INSTALLED IN AN AREA PROTECTED FROM THE ELEMENTS, SUCH AS WIND, RAIN, WATER (SPRAY OR

DRIP).

1. Place unit so the front side will be completely unobstructed to provide proper air flow. The unit may be closed in

on the top and three sides, but the front MMUUSSTTBBEEunobstructed for air circulation and proper operation.

Installation should be such that the cabinet can be moved for servicing if necessary.

2. Unit should be in a well ventilated area. Best results are obtained at temperatures between 650F (180C) and 800F

(270C) for built-in products and 650F (180C) and 900F (320C) for freestanding products.

3. Provisions for electricity and water connection should be determined before placing unit in proper place.

UUnniittssCCeerrttiiffiieeddffoorrOOuuttddoooorrUUssee--((ssttaaiinnlleesssssstteeeelloouutteerrccaabbiinneett))

1. Place unit so the front side will be completely unobstructed to provide proper air flow. The unit may be closed in

on the top and three sides, but the front MMUUSSTTBBEEunobstructed for air circulation and proper operation.

Installation should be such that the cabinet can be moved for servicing if necessary.

2. Unit should be in a well ventilated area with temperature above 450F (7.20C) and below 1100F (430C). Best results

are obtained at temperatures between 600F (160C) and 1000F (380C).

3. Provisions for electricity and water connection should be determined before placing unit in proper place.

4. For best performance, outdoor units should be installed away from direct sunlight or under a counter or shelter.

GENERAL INFORMATION

UUnnppaacckk

1. Remove banding from bottom of carton. Lift carton up and off of the unit.

2. Remove all tape and packaging material from the outside and inside of the cabinet.

3. Keep all carton packaging until your unit has been thoroughly inspected and found to be in good condition.

LEG LEVELER INSTALLATION

RReeaaddBBeeffoorreeIInnssttaalllliinnggLLeeggLLeevveelleerrss

WWAARRNNIINNGG::Do not lay unit on top, side, back, or front. If unit is accidentally laid

in any position other than right side up, then the unit must remain in the right side

up position for at least 24 hours before plugging the unit in.

1. Tip unit backwards so there is one foot of clearance on front of the unit. Have

someone to assist you in tilting the unit to prevent it from falling on you while

installing the leg levelers.

2. Screw front two (2) leg levelers into the weldnuts. Leg levelers should be

screwed in unit snug.

3. Repeat steps 1 & 2 with the exception of tipping the unit forwards to screw in

the back two leg levelers.

4. The leg levelers are now installed.

5. The unit should be level from front to back and side to side. If floor conditions

do not allow the unit to sit level, adjust the leg leveler by turning the required

leg leveler counter-clockwise to increase the height and clockwise to reduce

the height.

LLeeggLLeevveelleerr

((44))ppeerruunniitt

WWeellddnnuutt

((EEaacchhbboottttoomm

ccoorrnneerrooffuunniitt))

FULL OVERLAY PANEL INSTALLATION

Note: Weight of wood panel must not exceed 20 lbs.

WWooooddSSccrreewwss

1. A #8 pan head wood screw should be used to properly secure the wood frame. A total of 10 screws will be needed

for a 3 1/2” (8.9 cm) kickplate or 8 screws for a 4” (10.2 cm) kickplate.

2. Only use pan head screws.

3. DO NOT select a screw that is longer than the wood thickness at

the screw locations.

4. Use recommended pilot holes for the frame material. (See chart)

WWoorrkkiinnggMMaatteerriiaallWWooooddSSccrreewwSSiizzee##88

Hardwood 3/32 (0.24 cm)

Softwood 5/64 (0.20 cm)

AAsssseemmbblliinnggDDoooorrHHiinnggeeBBrraacckkeettss

(Disregard if hinge brackets are already attached)

1. Attach the top and bottom door hinge brackets to the door with the #10-32 machine screws and a 1/8” allen head

driver as shown in Figure 1 below.

2. Press in the shoulder bushings to the top and bottom door hinge brackets. Make certain that the shoulder is to the

outside of the door as shown in Figure 1 below.

3. Test fit the door to the unit to make certain door will hang correctly. The door is hung correctly when the top of the

door is parallel to the top of the unit. (See Figure 2) Adjustments can be made by loosening the door hinge

machine screws and moving the door hinge brackets on the door.

4. Tighten all four (4) machine screws after adjustments have been made.

5. Remove the door from the unit by removing the units top hinge set screw and angling the door off of the bottom

hinge pin.

Figure 1

Shoulder Bushing

Door Hinge Bracket

#10-32 Machine

Screw

Door Hinge

Screw Holes

Door Front

Surface

TTyyppiiccaallTTooppaannddBBoottttoomm

DDoooorrHHiinnggeeBBrraacckkeett

AAsssseemmbbllyy

Figure 2

This surface parallel to the unit.

(Right hinge door shown

SELECTING AND PREPARING THE OVERLAY PANEL

FFOORRAA33--11//22””TTOOEEKKIICCKK

((CCOOVVEERRSSTTHHEEEENNTTIIRREEDDOOOORREEXXTTRRUUSSIIOONN))

MMiinn..55//88””((11..77ccmm))

MMaaxx..33//44””((11..99ccmm))

223333//44””((6600..33ccmm))

11771155//1166””((4455..66ccmm))TTYYPP

551133//1166””((1144..88ccmm))

2233//3322““TTYYPP

1/4” x 3/8” Deep hinge screw clearance hole. Locate and drill using door

hinge hole after the door has been aligned to the unit and when the wood

is positioned on door.

MMoouunnttiinnggssuurrffaaccee((nnoonn--ffaaccee))ssiiddee

1/4” x 3/8” Deep hinge screw clearance hole. Locate and drill using door hinge hole

after the door has been aligned to the unit and when the wood is positioned on door.

MMoouunnttiinnggssuurrffaaccee((nnoonn--ffaaccee))ssiiddee

1133//1166””TTYYPP

BBootthhSSiiddeess

552233//3322””

((1144..66ccmm))

TTYYPP

115555//3322””

((3388..55ccmm))

TTYYPP

224411//22””

((6622..22ccmm))

TTYYPP

PPrree--ddrriilllleeddppiillootthhoolleess

1100ppllaacceess

330055//1166””

((7777..00ccmm))

TOP

DOOR

OOPPTTIIOONNAALLFFOORR44””TTOOEEKKIICCKK

TTOOMMAATTCCHHEEXXIISSTTIINNGGCCAABBIINNEETTRRYYTTOOEEKKIICCKKHHEEIIGGHHTT

MMiinn..55//88””((11..77ccmm))

MMaaxx..33//44””((11..99ccmm))

223333//44””((6600..33ccmm))

11771155//1166””((4455..66ccmm))TTYYPP

551133//1166””((1144..88ccmm))

2233//3322““TTYYPP

1/4” x 3/8” Deep hinge screw clearance hole. Locate and drill using door

hinge hole after the door has been aligned to the unit and when the wood

is positioned on door.

MMoouunnttiinnggssuurrffaaccee((nnoonn--ffaaccee))ssiiddee

1/4” x 3/8” Deep hinge screw clearance hole. Locate and drill using door hinge hole

after the door has been aligned to the unit and when the wood is positioned on door.

MMoouunnttiinnggssuurrffaaccee((nnoonn--ffaaccee))ssiiddee

1133//1166””TTYYPP

BBootthhSSiiddeess

552233//3322””

((1144..66ccmm))

TTYYPP

115555//3322””

((3388..55ccmm))

TTYYPP

224411//22””

((6622..22ccmm))

TTYYPP

PPrree--ddrriilllleeddppiillootthhoolleess

88ppllaacceess

22991133//1166””

((7755..77ccmm))

TOP

DOOR

ATTACHING THE OVERLAY PANEL TO THE DOOR

1. If the door is attached to the unit, remove by unscrewing the top allen head set screw at the top hinge. Remove

the door by angling the door off of the bottom hinge pin.

2. Peel back the door gasket to expose the screw holes.

3. Set the overlay panel flush to the front of the door in the desired location. Clamp the overlay panel to the door if

necessary.

4. Insert the wood screws through the back of the door into the pilot holes in the overlay panel and tighten.

5. Reinstall the door gasket by pressing into the door channel. Make certain the corners are inserted fully.

6. Install the door to the unit. Use the supplied plastic washer as shown in the figure below.

7. Realigning the door may be necessary. Any final door adjustments can be made using a 1/8” allen head driver to

adjust the door’s brackets. (See figure below)

8. Attach the door light striker plate as shown using the 5/16” hex or phillips head screws provided. Make certain the

light is able to turn on and off when the door is opened and closed.

9. Attach the door to the unit by reversing step number 1 above.

Magnetic door

gasket

Bottom of door

Attached overlay

panel

3/8” clearance

holes for

frame wood

screws -

10 holes

1/8” allen head screws for hinge

adjustment

Door hinge

adjustment screws

Door light striker plate

CAUTION

Door can become

disengaged if washers

are not installed.

CAUTION

Door can become

disengaged if

washers are not

installed.

Cabinet

Hinge

Overlay

Panel

Door Hinge Door Hinge

Shoulder bushing

3/4” OD x 7/16”

ID Washer

3/4” OD x 1/4” ID

Washer

(3) Nylon hardware

components at

bottom hinge

CAUTION

Door may not swing properly

if all nylon components are

not installed as shown

Bottom Hinge Cover

Overlay

Panel

HHiinnggeeHHaarrddwwaarreeIInnssttaallllaattiioonn

DDeettaaiillss

5/8”x 7/32” ID washer

Shoulder

bushing

(2) Nylon

hardware

components at

top hinge

Top Hinge Cover

Rear of Door

ELECTRICAL CONNECTION

EElleeccttrriiccaallRReeqquuiirreemmeennttss

A 115 volt, 60 Hz, AC only 15 amp fused electrical supply is required. (A

time delay fuse or circuit breaker is recommended.) It is recommended

that a separate circuit, serving only this appliance, be provided.

••EELLEECCTTRRIICCAALLGGRROOUUNNDDIISSRREEQQUUIIRREEDDOONNTTHHIISSAAPPPPLLIIAANNCCEE..

••DDOONNOOTTUUNNDDEERRAANNYYCCIIRRC

CUUMMSSTTAANNCCEESSRREEMMOOVVEETTHHEEPPOOWWEERR

SSUUPPPPLLYYCCOORRDDGGRROOUUNNDDPPLLUUGG..

••DDOONNOOTTUUSSEEAANNEEXXTTEENNSSIIOONNCCOORRDD

RReeccoommmmeennddeeddGGrroouunnd

diinnggMMeetthhooddss

For your personal safety, this unit must be grounded. This appliance is

equipped with a 7’ (2.1 m) power supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord

must be plugged into a mating 3-prong grounding type wall receptacle grounded in accordance with the National Electrical

Code and local codes and ordinances. If the circuit does not have a grounding type receptacle, it is the responsibility and

obligation of the customer to exchange the existing receptacle in accordance with the National Electrical Code and applicable

local codes and ordinances. The third ground plug SHOULD NOT, under any circumstances, be cut or removed. All UL listed

combination beverage center/ice makers are equipped with this type of plug.

WATER CONNECTION

Observe and follow all local code(s) when installing appliance.

•Connect to a potable, active cold water supply line delivering water pressure at a minimum of 20 psi and a maximum

of 120 psi.

•Use 1/4” copper water tubing only and the supplied connection fittings to connect to the water valve’s 3/4” garden

hose fitting located at therear of the unit.

•Make certain all water connections are watertight after installation. Form the tubing so that it will not vibrate against

the cabinet body or kink when your refrigerator is set in position.

Power Supply

with 3-prong

grounding plug

Grounding type wall

receptacle

WARNING

ELECTRICAL SHOCK HAZARD

Failure to follow these instructions could result

in fire or electrical shock.

FINAL PREPARATION

1. Some stainless steel parts may have a plastic protective wrap which must be peeled off. The interior of the unit should be

washed thoroughly with hot, soapy water, rinsed and wiped dry to remove film residue and any installation dust or debris

before being used. Solutions stronger than soap and water are rarely needed.

2. All stainless steel parts should be wiped with hot soapy water. If buildup occurs, do not use steel wool, abrasive cloths,

cleaners, or powders. If it is necessary to scrape stainless steel to remove encrusted materials, soak with hot, wet cloths to

loosen the material, then use a wood or nylon scraper. Do not use a metal knife, spatula, or any other metal tool to scrape

stainless steel; scratches are almost impossible to remove.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Viking Kühlschrank Handbücher

Viking

Viking Freestanding Refrigerated Drawer Technisches Handbuch

Viking

Viking F20413 Bedienungsanleitung

Viking

Viking Professional VIBB536R Bedienungsanleitung

Viking

Viking CFBI7360 Bedienungsanleitung

Viking

Viking Vcbb536rss Bedienungsanleitung

Viking

Viking FBI7360 Bedienungsanleitung

Viking

Viking F20481 Bedienungsanleitung

Viking

Viking VCSB483D Service-Handbuch

Viking

Viking VCFF136D Bedienungsanleitung

Viking

Viking Freestanding French DoorBottom-Mount Refrigerator/Freezerwith... Bedienungsanleitung

Viking

Viking Professional VCFB304 Bedienungsanleitung

Viking

Viking VCSF136D Series Bedienungsanleitung

Viking

Viking FDFB5361R Bedienungsanleitung

Viking

Viking CVBI7360 Bedienungsanleitung

Viking

Viking Designer DFBB536 Benutzerhandbuch

Viking

Viking RDFN536D Bedienungsanleitung

Viking

Viking Custom Front series Bedienungsanleitung

Viking

Viking FDBB5361 Series Bedienungsanleitung

Viking

Viking F20603D Bedienungsanleitung

Viking

Viking DDSB548SS Montageanleitung

Viking

Viking Designer DDSB483 Bedienungsanleitung

Viking

Viking Professional VCBF036RSS Bedienungsanleitung

Viking

Viking DFRB530 Series Benutzerhandbuch

Viking

Viking VURD144T Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung