Viking VURD140 Bedienungsanleitung

SERVICE MANUAL

Undercounter Refrigerator Drawer Units

Models

VURD140

DURD140

DFRD140

VIKING Preferred Service

1803 Hwy 82 West, Greenwood, Mississippi (MS) 38930 USA 662-455-1200

Important Information

SAVE THESE INSTRUCTIONS

REVIEW ALL SERVICE INFORMATION IN THE APPROPRIATE SERVICE MANUAL AND TECHNICAL SHEETS

BEFORE BEGINNING REPAIRS.

Pride and workmanship go into every product to provide our customers with quality products. It is possible, however,

that during its lifetime, a product may require service. Products should be serviced only by a qualified service

technician that is familiar with the safety procedures required in the repair and who is equipped with the proper tools,

parts, testing instruments, and the appropriate service manual.

Safety Information

We have provided many important safety messages in

this manual and on the appliance. Always read and obey

all safety messages. This is the safety alert symbol.

This symbol alerts you to hazards that can kill or hurt

you and others. All safety messages will be preceded by

the safety alert symbol and the word “DANGER”,

“WARNING” or “CAUTION”. These words mean:

DANGER

IMMEDIATE HAZARDS WHICH WILL RESULT IN

SEVERE PERSONAL INJURY OR DEATH.

WARNING

Hazards or unsafe practices which COULD result in

severe personal injury or death.

CAUTION

Hazards or unsafe practices which COULD result in

minor personal injury or product or property

damage.

All safety messages will identify the hazard, tell you how

to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

WARNING

To avoid risk of serious injury or death, repairs

should not be attempted by unauthorized personnel.

CAUTION

VIKING will not be responsible for any injury or

property damage from improper service procedures.

If performing service on your own product, you

must assume responsibility for any personal inju

or property damage which may resul ry

To locate an authorized servicer, call:

Viking Customer Service

Phone No. 1-888-845-4641

Address your written correspondence to:

Viking Preferred Service

1803 HWY 82 West

Greenwood, MS 38930

Remove Packaging

Your drawer refrigerator has been packed for ship-

ment with all parts that could be damaged by

movement securely fastened. Before installing the

drawer refrigerator, be sure all packing materials

and tape have been removed.

Important

Save the carton packaging until your drawer

refrigerator has been thoroughly inspected and

found to be in good condition. If there is damage,

the packaging will be needed as proof of damage

sustained in transit.

Note to Customer

This unit was carefully packed and thoroughly

inspected before leaving our plant. Responsibility

for its safe delivery was assumed by the carrier

upon acceptance of the shipment. As directed on

the side of the packaging carton, claims for loss or

damage sustained in transit must be made on the

carrier as follows:

Exterior Damage

Make a thorough damage notation on the delivery

receipt and have the driver acknowledge by sign-

ing and dating. Send a written request asking for

an inspection report from the carrier representa-

tive and the date the inspection was requested.

Retain the inspection report and receipt for filing of

a claim.

Concealed Damage

This must be reported to the carrier within fifteen

days. Obtain an inspection report from the carrier.

Retain the inspection report for filing of the claim.

DO NOT RETURN DAMAGED MERCHANDISE

TO THE MANUFACTURER - FILE THE CLAIM

WITH THE CARRIER.

STARTING OUT

Select Location

The proper location will ensure peak perform-

ance of your drawer refrigerator. Choose a loca-

tion away from heat and out of direct sunlight.

Best performance will be maintained when

installed within the following parameters:

Cabinet Clearance

Ventilation is required for the bottom front section of

the unit where the grille is located. Keep this area

open and clear of any obstructions. Adjacent cabi-

nets and countertop can be installed on top, back

and sides of the unit as long as grille and drawer

access remain unobstructed. An opening of 24” is

required between cabinets with a depth of 24”.

Adjacent cabinets and countertop can be installed

on top, back and sides of the unit as long as the

grille and drawer access remain unobstructed.

Ventilation is required for the bottom front section

of the unit where the grille is located. Keep this

area open and clear of any obstructions.

Make certain that the leveling legs supplied with

the drawer refrigerator are installed according to

the instructions. Leveling adjustments can be

made by raising or lowering the glides on the bot-

tom of the unit.

Important Safety Issue

A cabinet “anti-tip” device is mounted to the back

of your drawer refrigerator. If your installation is a

built-in undercounter application, you do not need

to apply this feature. If your installation is a free-

standing application with no counter top directly

above the top of the drawer refrigerator, you must

apply this feature to prevent the unit from tipping

forward when the drawers are pulled out. The

“anti-tip” device is attached at the back of each

cabinet. Please see installation instructions sup-

plied with the “anti-tip” device.

Electrical Connection

Check the serial nameplate for the correct power

supply. Use only the electrical power supply spec-

ified on the serial nameplate. Do not use an exten-

sion cord.

Grounding Method

This drawer refrigerator is equipped with a power

supply cord with ground. It must be plugged into a

mating grounding type receptacle in accordance

with the National Electrical Code and applicable

local codes and ordinances. It is the customer’s

responsibility to provide the proper grounding type

receptacle. Do not alter the plug in any way.

INSTALLATION

21.81

23.88

25.82

34.00

23.88

3.5

15.13

Ideal Ambient Temperature Range

built-in

freestanding

55-80°F

55-90°F

* Drawer Refrigerator will not perform correctly in ambient temperatures less than 55°F.

THIS UNIT SHOULD NOT, UNDER ANY

CIRCUMSTANCES, BE UNGROUNDED.

DISCONNECT POWER SOURCE BEFORE

ADJUSTING LEVELING LEGS

Control Panel

The temperature of your drawer unit ranges from

32°F to 47°F (0°C to 8°C. The temperature can be

adjusted using the control panel located on the

inside of the top drawer. To change the tempera-

ture setting, press the warmer or cooler pads until

the display shows the desired temperature. After a

few seconds the display will return to the actual

temperature of the unit. An empty unit will stabilize

in six to eight hours.

Your drawer refrigerator’s control leaves the facto-

ry preset to display its temperature in degrees

Fahrenheit. To change the display to show Celsius

temperatures, simply press the warmer and cold-

er key pads simultaneously. The display will

change within a few seconds.

The on/off key pad stops and starts the cooling of

the unit. This can be used when your drawer

refrigerator will not be used for extended periods

of time. The LED light will continue to operate

when the drawers are opened as long as the unit

is connected to a power source.

At time of initial start up the control panel display

will show “OR” for “Out of Range” until the unit

reaches the desired temperature. At any time the

unit’s interior temperature reaches 9 degrees

below or above its setpoint this code will also be

displayed.

FEATURES

TEMPERATURE CONTROL

WARMER

COOLER

OFF

Gastronorm Container Systems

For additional convenience, optional Gastronorm

food storage containers can be purchased from

your dealer. These stainless steel containers can

be used to easily access smaller food items and

are dishwasher safe.

Drawer Organizer

The Drawer Organizer is designed to be fully

adjustable to compensate for bottles and other

items of different sizes. The drawer Organizer can

be adjusted left and right, up and down by turning

the knob counter clockwise.

CARE AND CLEANING OF YOUR DRAWER REFRIGERATOR

Condenser

The condenser tubing inside the cabinet does not

require frequent cleaning; however, satisfactory

cooling depends on adequate ventilation over the

coils. Be sure that nothing obstructs the required

air flow openings in front of the cabinet. At least

once or twice a year brush or vacuum lint and dirt

from the grille. Also at least once or twice a year

brush or vacuum lint and dirt from the condenser

for efficient performance by unscrewing the grille

on the bottom front of the cabinet.

Interior

Clean the drawer gaskets as well as inside the

drawers with mild soap and water. Do not use an

abrasive powder, solvent, polish cleaner or undi-

luted detergent.

Cabinet

The painted cabinet can be washed with mild

soap and water and thoroughly rinsed with clear

water. Never use abrasive scouring powders.

Interior

Wash interior compartments with mild soap and

water. Do not use an abrasive powder, solvent,

polish cleaner or undiluted detergent.

Door Gasket

The vinyl gasket may be cleaned with mild soap

and water, a baking soda solution or a mild scour-

ing powder.

Care of Unit

1. Avoid leaning on the drawer fronts, you may

bend the door hinge or tip the unit.

2. Exercise caution when sweeping, vacuuming,

or mopping near the front of the unit. Damage

to the grille can occur.

3. Periodic cleaning of the inside of the unit. (See

Care and Cleaning of Your Drawer Refrigera-

tor section).

4. Periodic checking and/or cleaning of the front

grille and condenser coils as needed.

Normal Responsibilities of the Owner

• All freight charges

• Damage sustained in transit

• Mileage charge(s) for service calls

• Proper installation including installation of lev-

eling legs.

• Leveling of unit.

• Alterations to original equipment

• Cleaning and normal maintenance outlined in

this manual.

Help Prevent Tragedies

Each year, children die because they climb inside

a discarded refrigeration product, get trapped

inside and suffocate. Take precautions to prevent

such tragedies by removing the door, taping or

chaining it shut before discarding.

FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS

Pilot Hole Drill Sizes for Wood Screws

Wood Screw Size

Hardwood

Softwood

Work Material 8

3/32

5/64

5/16 PHILLIPS HEAD SCREWS

HOLDING DRAWER FRONT

GASKET

Step 2:

Remove Drawer Fronts

(Note: The overlay panel may be installed without

removing the drawer fronts from the drawer bod-

ies, but the full drawer assembly is not as easy to

handle as the drawer front alone.)

1. Remove drawer from unit. Begin by pulling out

the drawer. Locate the drawer lock which can be

found on the outside of the cabinet slide (fig. 1).

Push the back of the drawer lock forward and

then down, releasing the drawer from the cabinet

slide (fig. 2). Repeat this on the opposite side of

the drawer. Lift the drawer up from the slides at

90° to fully extricate the drawer from the cabinet

(fig. 3).

2. Remove drawer fronts. Do this by removing

the 8 phillips screws and washers securing the

drawer front to the drawer body. Mark lightly with

an erasable marker the position of the stainless

drawer liner as it secured to the stainless drawer

before removing screws.

3. Remove the gasket from the drawer front. Do

this by pulling the gasket out of the channel that

holds it to the drawer front .This will expose the

clearance holes for mounting the overlay panel.

Step 1:

Wood Screws Required

1. A #8 pan head wood screw should be used to

properly secure the overlay panel. A total of 8

screws will be needed.

2. Use only pan head screws.

3. Do not select a screw that is longer than the

wood thickness at the screw locations.

4. Use recommended pilot holes for the frame

material (see chart below).

figure 1

figure 2

figure 3

Step 3:

Sizing the Overlay Panel

Step 4:

Attaching the Overlay Panel to the Door

1. Set overlay panel on drawer front face and

align edges. Clamp panel in position and mark

pilot hole locations. See step 3 for nominal size

and hole locations. Drill pilot holes (remove panel

if necessary, re-align and re-clamp overlay to

drawer face).

2. Insert wood screws through clearance holes

and tighten to secure overlay panel.

3. Reinstall gasket into channel. Make sure the

corners are inserted fully.

Step 5:

Reattach Drawer Front to Drawer Body

1. Align mounting holes on drawer body with

mounting holes on drawer front. Align the door

liner to the front flanges by using the erasable

marker alignment lines that were applied prior to

removing the door from the drawer. Reinstall

phillips head screws and washers. Snug down,

but do not tighten fully, final adjustment of drawer

front will be done after reinstalling the drawer.

Step 6:

Reinstall the Drawer

1. Fully extend drawer slides and place drawer on

slides. Be sure that drawer sits evenly on both

slides.

2. Lock drawers into drawer slides. Push drawer

locks down and then back to relock the drawer

into the slide.

Step 7:

Adjust Drawer Front

1. Adjust drawer front to achieve a 1/8" gap from

the top of the drawer front to the top of the cabi-

net or (for bottom drawers) 1/8" from the top of

the drawer front to the bottom of the top drawer,

the drawer front should be centered between the

cabinet edges.

2. Fully tighten phillips head screws.

FULL OVERLAY PANEL INSTALLATION INSTRUCTIONS

11.81

23.06

.56 .56

7.59

14.63

15.19

23.63

TROUBLESHOOTING

POSSIBLE CAUSE

• Unit interior needs cleaned.

• Unit not level.

• Weak floor.

• LED light burned out.

• No power at outlet.

• Control Panel turned “OFF”.

• Line Cord not plugged into power

source.

• House fuse blown.

• Prolonged door openings.

• Control Panel set too cold.

• Condenser needs cleaning.

• Too many door openings.

• Prolonged door openings.

• Hot, humid weather increases

condensation.

• Hot, humid weather increases

condensation.

• Control improperly set.

• Faulty thermometer.

CORRECTION

• Clean inside of unit. See “Care and Cleaning” pg. 7.

• Adjust leveling legs. See leveling leg instructions.

• Rebuild floor or move to a different location.

• Replace LED light.

• Test outlet with lamp.

• Turn unit on with on/off pad on Control Panel.

• Plug unit into power source.

• Reset house fuse.

• Reduce number and/or duration of door openings.

• Raise temperature of unit via Control Panel.

• Clean condenser. See “Care of Unit” pg 7.

• Reduce number and/or duration of door openings.

• As humidity decreases, moisture will disappear.

• Move unit to cooler location.

• As humidity decreases, moisture will disappear.

• Move unit to cooler location.

• Reset to slightly warmer temperature.

• Reset control to desired temperature.

• Recheck with second thermometer.

PROBLEM

Odor in cabinet

Noisy operation

Unit vibrates

Interior light not working

Appliance will not run.

Appliance runs too long.

Moisture collects inside of unit.

Moisture collects on outside

surface of the unit.

Interior too hot/too cold

Diagnostic LED

In the back in the grille there is a diagnostic/status

LED. This led is used to help diagnosis any problems

with the unit and to tell its status.

LED Status

Not on

Continuously on

1 Blink and pause

2 Blink and pause

3 Blink and pause

Code/Problem

Unit does not have power

Unit is "ON" and operating correctly

For shorted or open thermistor

Disconnected Display Board

Compressor is locked out

Before Calling for Service

Before calling for service, check the following

items:

• Make sure unit is plugged into outlet.

• Check the outlet for power. Test outlet with

lamp to make certain outlet has power.

• Make sure drawer refrigerator is “ON”. Dis-

play will show.

• Make certain unit is level from front to back

and side to side.

• Use troubleshooting guide, page 7 for other

diagnosis.

If you are not able to correct the problem, contact

your dealer or the manufacturer. Be sure to have

the model number and the serial number handy

before you call. The model and the serial number

are located somewhere on your drawer refrigera-

tor.

How to Obtain Service

Your drawer refrigerator requires little service

because the best and most up-to-date materials,

equipment and quality control methods are

employed throughout the manufacturing process.

If trouble occurs during normal operation, read

"Things to remember" section first and, if neces-

sary, check the troubleshooting guide. If service

becomes necessary:

1. Contact the dealer where your appliance

was purchased or the manufacturer for the

name of the nearest authorized service rep-

resentative. The service representative will

have full authority to make any repairs

deemed necessary.

2. If you are in an area where there is no serv-

ice representative, write or call the manufac-

turer directly. We will make recommenda-

tions as to the proper procedure for correc-

tion. Service work and replacement parts, if

required, will be provided as covered by your

limited warranty.

3. In all correspondence regarding service, be

sure to give the model number, serial num-

ber and proof of purchase.

4. Try to have information or description of the

nature of the problem, how long the unit has

been running, the room temperature and

any additional information that may be help-

ful in quickly solving the problem.

Every new drawer refrigerator that leaves the factory

contains this Owner's Guide. Keep this Owner's

Guide in a safe place for convenient reference.

For Your Records

OBTAINING SERVICE

SEND IN YOUR WARRANTY RECORD CARD

IMMEDIATELY AFTER TAKING DELIVERY OF

YOUR DRAWER REFRIGERATOR.

Date of Purchase

Dealer's Name

Dealer's Address

Dealer's city Dealer's State Zip

Appliance Serial Number

Model Number

Date Warranty Card Mailed (within 10 days of purchase)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Viking Kühlschrank Handbücher

Viking

Viking DUAR143 Bedienungsanleitung

Viking

Viking FDBB5361 Series Bedienungsanleitung

Viking

Viking Professional VISB548D Bedienungsanleitung

Viking

Viking VCSB5481 Series Handbuch

Viking

Viking F20603A Bedienungsanleitung

Viking

Viking Built-in French Door Bottom-Freezer... Bedienungsanleitung

Viking

Viking F20413 Bedienungsanleitung

Viking

Viking FDSB5481 Series Montageanleitung

Viking

Viking DFUR Technisches Handbuch

Viking

Viking FDFB5361R Bedienungsanleitung

Viking

Viking RDFN536D Bedienungsanleitung

Viking

Viking Bottom-Mount Bedienungsanleitung

Viking

Viking 5 Series Bedienungsanleitung

Viking

Viking Professional VIBB536R Bedienungsanleitung

Viking

Viking Quiet Cool VCFB5301 Bedienungsanleitung

Viking

Viking VCFF136D Bedienungsanleitung

Viking

Viking DFRB530 Series Bedienungsanleitung

Viking

Viking VCRB5303 Bedienungsanleitung

Viking

Viking Designer DFBB536 Benutzerhandbuch

Viking

Viking F20481 Bedienungsanleitung

Viking

Viking F20394E EN Bedienungsanleitung

Viking

Viking DDSB548SS Montageanleitung

Viking

Viking Professional VCFB530 Bedienungsanleitung

Viking

Viking Designer DDRB364 Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung