Viking VURE524G Bedienungsanleitung

VURE515G

VURE524G

5 SERIES

Undercounter Refrigerator

Install / Use & Care

MANUAL

Congratulations

We hope you will enjoy and appreciate the care and attention we have put into every detail of your new, state-of-the-art Viking

refrigerator

Your appliance is designed to oer years of reliable service. This Use and Care Guide will provide you with the information you

need to become familiar with your refrigerator’s care and operation. For additional information, visit our website at vikingrange.

com..

Your complete satisfaction is our ultimate goal. If you have any questions or comments about this product, contact our Consumer

Support Center at 1-888-845-4641.

We appreciate your choice of our undercounter refrigerator and hope that you will again select our products for your other major

appliance needs. For more information about the complete and growing selection of our products, visit us online at vikingrange.

com

Safety and Warnng __________________________________________________________________________________ 3

Disposal and Recycling________________________________________________________________________ 3

Environmental Requirements __________________________________________________________________ 3

Installation _________________________________________________________________________________________ 4

Cutout and Product Dimensions ________________________________________________________________ 4

Side by Side Installation _______________________________________________________________________ 5

Anti-Tip Bracket______________________________________________________________________________ 6

Leveling____________________________________________________________________________________ 7

Grille Installation_____________________________________________________________________________ 8

Door Swing _________________________________________________________________________________ 8

Door Adjust_________________________________________________________________________________ 9

Operating Instructions ______________________________________________________________________________ 10

First Use___________________________________________________________________________________ 10

Control Operation___________________________________________________________________________ 10

Airow and Product Loading __________________________________________________________________ 11

Interior Adjustments_________________________________________________________________________ 12

Wine Guide ________________________________________________________________________________ 13

Food Preservation Guide _____________________________________________________________________ 15

Maintenance ______________________________________________________________________________________ 16

Cleaning __________________________________________________________________________________ 16

Cleaning Condenser _________________________________________________________________________ 17

Extended Non-Use __________________________________________________________________________ 17

Troubleshooting ____________________________________________________________________________ 18

Service Information_________________________________________________________________________________ 19

Warranty__________________________________________________________________________________________ 20

Table of Contents

Safety and Warning

NOTICE

Please read all instructions before installing, operating, or

servicing the appliance.

Use this appliance for its intended purpose only and follow

these general precautions with those listed throughout this

guide:

SAFETY ALERT DEFINITIONS

Throughout this guide are safety items labeled with a

Danger, Warning, or Caution based on the risk type:

Danger means that failure to follow this safety statement will

result in severe personal injury or death.

Warning means that failure to follow this safety statement

could result in serious personal injury or death.

Caution means that failure to follow this safety statement

may result in minor or moderate personal injury, property, or

equipment damage.

This unit contains R600a (Isobutane) which is a ammable

hydrocarbon. It is safe for regular use. Do not use sharp

objects to expedite defrosting. Do not service without

consulting the“R600a specications”section included in the

User Guide. Do not damage the refrigerant circuit.

Service must be done by factory authorized service

personnel. Any parts shall be replaced with like components.

Failure to comply could increase the risk of possible ignition

due to incorrect parts or improper service.

CALIFORNIA PROPOSITION 65

This product contains chemicals known to the state of

California to cause cancer and birth defects or other

reproductive harm. www.P65warnings.CA.gov

This equipment is to be installed with adequate backow

protection to comply with applicable federal, state and local

codes.

Disposal and Recycling

RISK OF CHILD ENTRAPMENT. Before you throw away your

old refrigerator or freezer, take o the doors and leave

shelves in place so children may not easily climb inside.

If the unit is being removed from service for disposal, check

and obey all federal, state, and local regulations regarding

the disposal and recycling of refrigeration appliances, and

follow these steps completely:

1. Remove all consumable contents from the unit.

2. Unplug the electrical cord from its socket.

3. Remove the door(s)/drawer(s)

Environmental Requirements

This model is intended for indoor/interior applications only

and is not to be used in installations that are open/exposed

to natural elements.

This unit is designed to operate between 50°F (10°C) and

100°F (38°C). Higher ambient temperatures may reduce the

unit’s ability to reach low temperatures and/or reduce ice

production on applicable models.

For best performance, keep the unit out of direct sunlight

and away from heat generating equipment.

In climates where high humidity and dew points are present,

condensation may appear on outside surfaces. This is

considered normal. The condensation will evaporate when

the humidity drops.

Damages caused by ambient temperatures of 40°F (4°C) or below

are not covered by the warranty.

DANGER

WARNING

CAUTION

WARNING

DANGER

CAUTION

Cutout & Product Dimensions

PREPARE SITE

Your product has been designed for either free-standing or

built-in installation. When built-in, your unit does not require

additional air space for top, sides, or rear. However, the front

grille must NOT be obstructed, and clearance is required for

an electrical connection in the rear.

CAUTION

Unit can NOT be installed behind a closed cabinet door.

CUTOUT DIMENSIONS

PRODUCT DIMENSIONS

REAR

Power Cord

6 ft (183 cm)

1 ¾”

(44 mm)

6 ⁄”

(159 mm)

14 ⁄”

(379 mm)

3 ½”

(89 mm)

33 ⁄” to 34 ⁄”

(855 mm to

881 mm)

29 ⁄”

(754 mm)

2 ¾”

(70 mm)

10 ⁄”

(271 mm)

17 ½”

(445 mm)

21 /”

(535 mm)

24 /”

(616 mm)

22 ⁄”

(583 mm)

25 ⁄”

(652 mm)

4 ⁄“ (111 mm)

17 /”

(445 mm)

*Add ⁄”for integrated models with ⁄” panel installed.

1 ⁄" (38 mm)

(178 mm)

15 ⁄"

(386 mm)

34 ⁄"

(870 mm)

35 ⁄"

(889 mm)

Preferred location

for electrical outlet

is in an adjacent

cabinet.

24"

(610 mm)

⁄"

(16 mm)

Installation

(102 mm)

(178 mm)

33-⁄"

(860 mm)

34-⁄"

(886 mm)

23-⁄"

(607 mm)

Preferred location

for electrical outlet

is in adjacent

cabinet.

24"

(610 mm)

⁄"

(16 mm)

VURE515

VURE524

Power Cord

6 ft (183 cm)

1 ⁄”

(35 mm)

11 ¾”

(298 mm)

VURE515

VURE524

18 ⁄”

(481 mm)

26 ⁄”

(664 mm)

21 ⁄”

(535 mm)

2 ¾”

(70 mm)

VURE515 VURE524

23 ⁄”

(600 mm)

3 ½”

(89 mm)

33 ⁄”to 34 ⁄”

(855 mm to

881 mm)

29 ⁄”

(754 mm)

VURE515 VURE524

FRONT

TOP

SIDE

Side-by-Side Installation

OTHER SITE REQUIREMENTS

Side-by-Side Installation

Units must operate from separate, properly grounded electrical

receptacles placed according to each unit’s electrical specications

requirements.

Cutout width for a side-by-side installation is the total of the widths

listed under Cutout Dimensions in each unit’s Installation Guide.

Each door can be opened individually (one at a time) without

interference.

Installation

However, to ensure unobstructed door swing (opening both doors

at the same time), 1/4”(6.4 mm) of space needs to be maintained

between the units.

Hinge-by-Hinge Installation (Mullion)

When installing two units hinge-by-hinge, 13/16”(22 mm) is

required for integrated models. Additional space may be needed for

any knobs, pulls or handles installed.

Stainless steel models which include the standard stainless handle

will require 4-9/16”(116 mm) to allow both doors to open to 90° at

the same time.

1/4" (6 mm)

13/16" (22 mm)

4 - 9/16" (116 mm)

Anti-Tip Bracket

Use one of the methods below to secure the unit

CABINET/COUNTER ANTI-TIP INSTALLATION

(For built-in applications)

1. Slide unit out so screws on front of unit are easily

accessible.

2. Remove the two screws from the front of the unit.

3. Bend bracket along one of the perforations to allow

attachment to the desired adjoining surface.

4. Gently push unit into position. Be careful not to

entangle the electrical cord or water line, if applicable.

5. Check to be sure the unit is level from front to back

and side to side. Make any necessary adjustments. The

unit’s top surface should be approximately ⁄” (3 mm)

below the countertop.

6. Secure bracket to adjoining surface.

FLOOR MOUNTED ANTI-TIP INSTALLATION

(For free-standing applications)

1. Locate two anti-tip brackets included with the kit.

2. Place the unit into the area where it will be installed.

Check the door, sides, and top for a proper t. Also test

to make sure the door opens and closes freely.

3. Remove grille and place a mark on the oor at the front

of the unit. Also place a mark on the oor in the center

of the unit.

4. Remove the unit. Using a square, extend center line“B”

(see chart below). This line serves as the back edge for

the anti-tip brackets. From the center line, measure“A”

to the left and right. This line is the outer edge of each

bracket.

515 524

A7 ⁄”(194 mm) 11 ⁄”(303 mm)

B22”(558 mm) 22”(558 mm)

5. Place the anti-tip brackets on the oor against the line

drawn for the outer edge. Mark spots for the screw

holes.

Surrounding

area (Top view)

Drill holes and

mount anti-tip

brackets to ﬂoor Back wall

Front

unit

Back

unit

6. Use a 1/8”drill to make two starter holes and fasten

the anti-tip brackets to the oor using the screws

provided.

7. Place the unit back into position, making sure the

feet engage the anti-tip brackets properly. Check the

alignment of the lines made on the oor in step 3

with the position of the front feet to ensure proper

positioning.

Back wall

Back of unit

Front of unit

Surrounding

area (Top view)

Installation

LEVELING INFORMATION

1. Use a level to conrm

the unit is level. Level

should be placed

along top edge and

side edge as shown.

2. If the unit is not level, adjust the legs on the corners of

the unit as necessary.

3. Conrm the unit is level after each adjustment and

repeat the previous steps as needed.

INSTALLATION TIP

If the room oor is higher than the oor in the cutout

opening, adjust the rear legs to achieve a total unit rear

height of ⁄”(3 mm) less than opening’s rear height. Shorten

the unit height in the front by adjusting the front legs. This

allows the unit to be gently tipped into the opening. Readjust

the front legs to level the unit after it is correctly positioned

in the opening.

1. Plug in the power/electrical cord.

2. Gently push the unit into position. Be careful not to

entangle the cord or water and drain lines, if applicable.

3. Re-check the leveling, from front to back and side to

side. Make any necessary adjustments. The unit’s top

surface should be approximately ⁄”(3 mm) below the

countertop.

4. Install the anti-tip bracket.

5. Remove interior packing material and wipe out the

inside of the unit with a clean, water-dampened cloth.

Turn to Adjust

Installation

Grille Installation

REMOVING AND INSTALLING GRILLE

Disconnect electric power to the unit before removing the

grille.

When using the unit, the grille must be installed.

DO NOT touch the condenser ns. The condenser ns are

SHARP and can be easily damaged.

Removing the grille

1. Disconnect power to the unit.

2. Loosen the two screws (1).

3. Remove grille (2) from unit.

Installing the grille

1. Align cabinet and grille holes and secure, but do not

over tighten grille screws (1).

2. Reconnect power to the unit.

Door Swing

Units have a zero clearance for the door to open 90o, when

installed adjacent to cabinets.

Stainless steel models require 2-1/8” (54 mm) door clearance

to accommodate the handle if installed next to a wall.

WARNING

Wall

Stainless Steel, Black and White

90°

Door Swing

2-1/8" Min.

(54 mm)

Installation

Door Adjustments

DOOR ALIGNMENT AND ADJUSTMENT

Align and adjust the door if it is not level or not sealing properly. If

the door is not sealed, the unit may not cool properly, or excessive

frost or condensation may form in the interior.

NOTICE

Properly aligned, the door’s gasket should be rmly in contact

with the cabinet all the way around the door (no gaps). Carefully

examine the door’s gasket to ensure that it is rmly in contact

with the cabinet. Also make sure the door gasket is not pinched

on the hinge side of the door.

Do not attempt to use the door to raise or pivot your unit. This

would put excessive stress on the hinge system.

Alignment and Adjustment Procedure

1. Open door and remove gasket near the hinges.

2. Using a T-25 Torx bit, loosen each pair of Torx head

screws both the upper and lower hinge plates.

3. Square and align door as necessary.

4. Tighten Torx head screws on hinge.

5. Reinstall gasket into the channel starting at the corner.

REVERSING THE DOOR

1. Open door.

2. Using T-25 Torx bit loosen screw #1 and remove screw #2 on

top and bottom hinge. Slide and remove the door from the

unit.

Note: One hinge includes a metal spacer. Spacer must be used

with that hinge when reversing the door.

3. Remove caps from screw heads on opposite side (2 on top and

2 on bottom). Using #2 Phillips bit, remove the 4 underlying

screws. Reinstall the screws and caps on the opposite side.

4. Partially install screw #1 in the outer most holes on top and

bottom. Rotate door 180o, align hinge over screw #1 and

slide/seat into position. Reinstall screw #2 on top and bottom.

Tighten both screws and install hinge cover.

Align and adjust the door:

Align and adjust the door (see DOOR ALIGNMENT AND

ADJUSTMENT).

T-25 Torx Screw

CAUTION

Installation

Initial startup requires no adjustments. When plugged in, the unit will begin operating under the factory default settings. If the unit

was turned o during installation, simply press and the unit will immediately switch on. To turn the unit o, press .

If the temperature displayed is dierent than selected, the unit is progressing towards the selected temperature. Time to reach set

point varies based upon ambient temperature, temperature of product loaded, door openings, etc. Viking recommends allowing

the unit to reach set points before loading.

NOTICE: Temperature displayed reects actual temperature inside unit.

First Use

Control Operation

CONTROL FUNCTION GUIDE

Hidden

Button

This unit is Star-K certied. See www.star-k.org for more details.

FUNCTION COMMAND NOTES

ON/OFF Press and release Unit will immediately turn On or OFF

Adjust Temperature Press or and release

When the display is ashing, press or to adjust the

set point temperature. Note: temperature displayed is the

actual temperature inside unit

Toggle between ºF / ºC Hold and for 5 seconds The display will change units

Leave interior light on Press and release to leave interior light on

for 12 hours; press again to deactivate

After 12 hours, factory default is restored; light will turn on

when door is open

Hide Display Hold hidden button and press Display will turn o when door is closed. Unit will continue

to operate. Repeat command to turn on display

Adjust light color While holding press and release to

scroll through lighting options

Option Open Door Closed Door

0 0 White White

0 1 Blue Blue

0 2 White Blue

Light will be set at full intensity when door is open, and 50%

intensity when door is closed.

Enable Sabbath Mode Press and hold for 5 seconds and release

The oF / oC symbol will ash briey after 5 seconds. Interior

light and display will go dark and remain so until user resets

mode - unit continues to operate

Disable Sabbath Mode Press and release Display and interior light return to normal operation

Showroom Mode Hold and for 5 seconds

The ºF / ºC symbol will ash. Display will be lit and interior

light will function. Unit will not cool. Repeat command to

return to normal operation

DOOR ALERT NOTIFICATION

When the door is left open for more than 5 minutes:

• A tone will sound for several seconds every minute

• will appear in display

• Closed door to silence alert and reset

Operating Instructions

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Viking Kühlschrank Handbücher

Viking

Viking VUAR143TRSS Bedienungsanleitung

Viking

Viking Combination Beverage Center Technisches Handbuch

Viking

Viking RDFN536D Bedienungsanleitung

Viking

Viking DFSB548 Series Bedienungsanleitung

Viking

Viking Professional VCBF036RSS Bedienungsanleitung

Viking

Viking VUAR140T Bedienungsanleitung

Viking

Viking Designer DDFF136SS Montageanleitung

Viking

Viking Freestanding French DoorBottom-Mount Refrigerator/Freezerwith... Bedienungsanleitung

Viking

Viking Designer DDFF136SS Bedienungsanleitung

Viking

Viking Professional VCSF036SS Produkthandbuch

Viking

Viking Designer DDFF136DSS Bedienungsanleitung

Viking

Viking Built-in French Door Bottom-Freezer... Bedienungsanleitung

Viking

Viking Professional VIRB364 Bedienungsanleitung

Viking

Viking CFDCFB5363 Bedienungsanleitung

Viking

Viking Designer DFRB364 Bedienungsanleitung

Viking

Viking VISB423 Bedienungsanleitung

Viking

Viking DFFB304 Benutzerhandbuch

Viking

Viking W10581473 Bedienungsanleitung

Viking

Viking FDBB5361 Series Bedienungsanleitung

Viking

Viking VCBF136RSS Montageanleitung

Viking

Viking Professional VCFB304 Bedienungsanleitung

Viking

Viking Designer DDSF136DSS Bedienungsanleitung

Viking

Viking Professional VISB548BR Bedienungsanleitung

Viking

Viking Designer DDSB483 Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung