Vinotemp WINE-MATE WM-2500HZD Gebrauchsanweisung

www.winemate.com

Wine Cooling System

WM-1500HZD, WM-

2500HZD WM-3500HZD,

WM-4500HZD WM-

6500HZD, WM-8500HZD

Installation, Use & Care Manual

www.vinotemp.com

Read and save these instructions

-1-

Important Safety Information

NOTES:

•

Do not plug in until 24 hours after delivery.

•

Do not use a ground fault interrupter (GFI).

•

A dedicated 20 AMP circuit for WM-1500~2500HZD and 30 AMP for WM-

3500~8500HZD are required.

WARNING

To avoid the risk of electrical shock, property damage, personal injury, or death:

•The power cord must be plugged into a 3-prong grounding type wall

receptacle, grounded in accordance with the National Electrical Code,

ANSI/NFPA 70 –latest edition and local codes and ordinances.

•It is the personal responsibility of the consumer to have a proper 3-prong wall

receptacle installed by a qualified electrician.

•DO NOT, UNDER ANY CIRCUMSTANCES, REMOVE THE POWER CORD

GROUNDING PRONG.

•A separate adequately fused and grounded circuit should be available for this

appliance.

•Do not remove any grounding wires from individual components while servicing

unless the component is to be removed and replaced. It is extremely important

to replace all grounding wires when components are replaced.

WARNING

-2-

ELECTRICAL SHOCK HAZARD

•Disconnect electrical supply from appliance before servicing.

•Replace all panels before operating.

•Failure to do so could result in death or electrical shock.

-3-

Table of Contents

Features & Specifications..................................................3

Installation Instructions…..................................................6

Temperature & Humidity… ..............................................16

Care Guide........................................................................20

Troubleshooting…............................................................21

Electrical Diagrams… ......................................................24

Customer Support…........................................................26

Warranty….........................................................................27

-4-

Features and Specifications

oHZD series cooling units are designed and used to provide a stable

temperature between 50~65 °F for a properly insulated space.

oThe refrigerated space will maintain humidity ranges within 50~70% RH.

oThese temperature and humidity ranges are optimized for long term

storage of wine.

oTemperature is controlled and humidity is adjusted using

▪innovative technology.

oHorizontal cold-air supply is optimized for use in the wide cabinets or wine

rooms.

oThe unit is self-contained ready for easy installation and use.

Fig. 1.1 WM-1500~2500HZD FEATURE DESCRIPTIONS

-5-

Fig. 1.2 WM-3500~8500HZD FEATURE DESCRIPTIONS

Fig. 1.3 WM-1500~2500HZD DIMENSIONS

-6-

Fig. 1.4 WM-3500~8500HZD DIMENSIONS

The specifications and dimensions are listed as follows:

Model

CFM

Cellar Size

(cu ft)

Dimensions

W”XD”XH”

Electrical

Weight(lb)

WM-1500HZD

120

14.25X16X13.25

115V/60HZ/4A

WM-2500HZD

180

200

14.25X16X13.25

115V/60HZ/5A

WM-3500HZD

250

650

14.25X21.25X19.75

115V/60Hz/6A

WM-4500HZD

250

1000

14.25X21.25X19.75

115V/60Hz/9A

WM-6500HZD

500

1500

17X28X22

115V/60Hz/14A

110

WM-8500HZD

500

2000

17X28X22

115V/60Hz/16A

110

NOTES:

•

Also see the voltage, frequency and current specified on the label at the

cooling unit.

•

The rated capacity is determined under the cellar and ambienttemperatures

of 55°F and 75°F with R13 interior and R19 exterior insulations. Any lower

cellar temperature, higher ambient temperature and less insulation will

cause reducing capacity and may not maintain 55°F.

•

The ambient temperatures for WM-1500HZD shall not be higher than78°F

or lower than 50°F in order to operate properly.

•

The ambient temperatures for WM-2500HZD shall not be higher than95°F

or lower than 50°F in order to operate properly.

•

The ambient temperatures for WM-3500~8500HZD shall not be higher than

95°F or lower than 50°F in order to operate properly.

-7-

Installation Instructions

WARNING

•Always check wiring harness connections before initiating any test procedures.

•Disconnect electric power from the appliance before performing any

maintenance or repairs.

•Voltage checks should be made by inserting meter proves beside the wires in

the connector blocks with the electric power source on and the connector block

plugged in.

•Resistance checks should be made on components with the electric power off

and the connector block disconnected.

NOTES:

•

Mounting brackets, screws, gaskets and other seal materials are not included.

•

Do not install any ducts onto the supply, return, intake and exhaust.

•

Because of potential safety hazards under a certain condition we strongly

recommend against the use of an extension cord. However, if you still select to

use an extension cord, it is absolutely necessary that it is a UL LISTED 3- wire

grounding type appliance extension cord having a 3-blade groundingplug

and a 3-slot receptacle that will plug into the appliance. The marked rating of

the extension cord shall be 115 V, 15 A or equivalent for WM- 1500~2500HZD

and 115 V, 20 A or equivalent for WM-3500~8500HZD and not greater than

15ft in length.

1. General Instructions

•

The cooling unit produces cooling supplied into the cellar, meanwhile it also

generates heat that must be exhausted outside the cellar. So the cold- air supply

with return-air intake side and thehot-air exhaustwith ambient-air intake side must

be separated and sealed. Through-wall installations can separate these two sides.

•

Furthermore, the condenser of cooling unit must intake adequate fresh ambient-

air to work properly. The ambient-air intake and hot-air exhaust must not be short-

circulated. Both of them must remain unobstructed 36” clearanceall around. The

area into which the hot air is exhausted must be well ventilated. If it is not, heat

generated by the unit will build up and the unit will not operate properly.

•

Additionally, cold-air supply from the front grille must remain unobstructed 36”

clearance.

•

The ambient temperatures shall not be above and below what are specified.

-8-

2. WM-1500~2500HZD cabinet installation

•

Cut a rectangular inside opening with the 1/4” clearance inwards to the width and

height of the cooling unit. By not going through, leave 1/2” lip inside at thewall to

place the gaskets (see Fig 2.1).

•

If top exhaust installation, cut another rectangular opening at the top of the cabinet

to the length and width of the top exhaust.

•

Install 2 pieces of 1/4” ID wood thread inserts at the ceiling (see Fig.2.1 & 2.2).

•

Place the gaskets (1/2” foam tape) on the mounting lip sides (see Fig 2.3).

•

If top exhaust installation, place another gaskets along the top exhaust at thetop

of the cooling unit (see Fig.2.4).

•

Move the cooling unit towards the mounting sides and push to press the

gaskets (see Fig 2.5).

•

Use 2 brackets and ¼” screws with 7/16” wrench to secure the cooling unit

(see Fig 2.6).

•

Install the cabinet grille on the cabinet exterior wall (see Fig. 2.7).

•

Plug the cooling unit in the cabinet receptacle.

•

Plug the wine cabinet.

Fig. 2.1 CABINET CUTOUT & GASKET LIP

-9-

Fig. 2.2 THREAD INSERT

Fig. 2.3 REAR GASKET

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vinotemp Küchengerät Handbücher

Vinotemp

Vinotemp Element EL-WCU103-02 Bedienungsanleitung

Vinotemp

Vinotemp Designer VT-DS26SB149 Bedienungsanleitung

Vinotemp

Vinotemp Portofino Series Bedienungsanleitung

Vinotemp

Vinotemp Element EL-300DSWL Bedienungsanleitung

Vinotemp

Vinotemp element EL-WCU113-03 Bedienungsanleitung

Vinotemp

Vinotemp element EL-24WCUB Bedienungsanleitung

Vinotemp

Vinotemp VT-WINEDISP4 Bedienungsanleitung

Vinotemp

Vinotemp element EL-WCU101-03 Bedienungsanleitung

Vinotemp

Vinotemp VT-BLKBEV Bedienungsanleitung

Vinotemp

Vinotemp element EL-33WCST Bedienungsanleitung

Vinotemp

Vinotemp Element EL-168GFEB Bedienungsanleitung

Vinotemp

Vinotemp WINE-MATE WM-3500HZD Bedienungsanleitung

Vinotemp

Vinotemp Element EL-30SWCB2D Bedienungsanleitung

Vinotemp

Vinotemp Element BCU101-01 Bedienungsanleitung

Vinotemp

Vinotemp ELEMENT EL-54SDTH Bedienungsanleitung

Vinotemp

Vinotemp WINE-MATE WM-6500D-DE Gebrauchsanweisung

Vinotemp

Vinotemp VT-8TEDTS-ID Bedienungsanleitung

Vinotemp

Vinotemp VT-BD Bedienungsanleitung

Vinotemp

Vinotemp element EL-28TS Bedienungsanleitung

Vinotemp

Vinotemp ELEMENT EL-BWC30TB-S Bedienungsanleitung

Vinotemp

Vinotemp VT-DS24SB50 Bedienungsanleitung

Vinotemp

Vinotemp element EL-155SDWS Bedienungsanleitung

Vinotemp

Vinotemp element EL-40WCST Bedienungsanleitung

Vinotemp

Vinotemp VT-32TSFE-SM Bedienungsanleitung

Beliebte Küchengerät Handbücher anderer Marken

Tayama

Tayama TYG-35AF Bedienungsanleitung

AEG

AEG 43172V-MN Bedienungsanleitung

REBER

REBER Professional 40 Benutzerhandbuch

North American

North American BB12482G / TR-F-04-B-NCT-1 Bedienungsanleitung

Presto

Presto fountain popper Bedienungsanleitung

Westmark

Westmark 1035 2260 Bedienungsanleitung

Zanussi

Zanussi ZCG64396XA Bedienungsanleitung

HOFFEN

HOFFEN SM-9302M Bedienungsanleitung

Philips

Philips HD3133 Bedienungsanleitung

Ronco

Ronco Beef Jerky Bedienungsanleitung

Hendi

Hendi 470411 Bedienungsanleitung

Livoo

Livoo MEN386 Bedienungsanleitung

croydon

croydon WR-10313-700 Bedienungsanleitung

Chefman

Chefman RJ43-SQ Series Bedienungsanleitung

Vacmaster

Vacmaster VP680 Bedienungsanleitung

Jetmaster

Jetmaster 900HG Bedienungsanleitung

Küppersbusch

Küppersbusch EEH 610.0 Kurzanleitung zur Einrichtung

HURAKAN

HURAKAN HKN-F10 Bedienungsanleitung