Vinpower HDDMINI Bedienungsanleitung

Reference Manual for HDDMINI

Hard Drive Duplicator

V 1.0

Device Menu Overview

This system comes with many features that can be accessed/adjusted by various functions and

settings within the operation menu. Please see the detailed descriptions below:

1. Copy

This process will copy the source hard drive, which is inserted into the Source Port, onto

one or multiple target hard drives simultaneously.

2. Copy+Compare

This function performs the Copy process, after which, it will perform a Compare process

automatically to ensure data accuracy.

3. Erase

This function erases the hard drives(s) connected to any port other than the Source Port.

There are three options for this function:

Quick Erase: It will erase only the beginning section of the hard drive, which is just

enough to make it look empty.

Full Erase: It will erase the entire hard drive by writing 0’s throughout. The erase

timeframe varies depending on the data capacity of the hard drive.

DOD Erase: It will erase the hard drive thoroughly to avoid any possible chances

of recovery. User will be prompted for # of passes to perform, the more pass rounds

selected, the lower the risk of data contents being recovered, but also the longer

the time the process will take.

4. Copy Mode

This setting will allow for the selection of a Copy Mode. There are 3 options:

Smart: This mode is the recommended and fastest approach to making copies

since it will analyze the source hard drive on supported file systems (FAT16/32,

NTFS, exFAT, ext2/3/4) and copy only the area that contains data. If the file system

on the source hard drive is NOT being supported, the system will automatically

shifts to RAW mode.

RAW: This mode is the safest and slowest approach to making copies since it will

copy the entire source hard drive bit by bit.

5. Setup

1) Language

This setting will allow you to choose the display language of the system.

2) Buzzer

This setting will allow the choice to hear a beep sound when a button is pressed

or when a task has been completed.

3) Screen Saver

This setting will allow the choice to enable the Screen Saver feature or not. By

enabling this feature, a screen saver will be displayed when the system has been

idle for an extended period.

4) Read Error Skip*

This setting will allow for the change to the number of times the system will skip

ahead when it encounters a reading error, while reading the source hard drive.

By default, the system does not skip any reading error, which would result in an

immediate job failure if any read error occurred during the duplication process.

*Enable this setting will not fix any discovered error(s); it will merely skip it and read

the remaining data of the source hard drive.

5) Write Error Skip*

This setting will allow for the change to the number of times the system will skip

ahead when it encounters a writing error, while writing to the target hard drive.

By default, the system does not skip any writing error, which would result in an

immediate failure for such target hard drive if any write error occurred during the

duplication process.

*Enable this setting will not fix any discovered error(s); it will merely skip it and

continue write to the next data block of the target hard drive.

6) Partition Layout

This setting will allow user to adjust various partition layout options for the target

hard drive during the duplication process under “SMART”/”Partition” mode.

There are two options for this setting:

Auto Ratio: The system will automatically adjust the partition layout under the

same ratio as the source hard drive.

As It: The system will set the partition layout exactly same as the source hard

drive regardless the capacity differences.

7) Size Tolerance

Normally, the capacity of the target hard drive is required to be greater than the

source hard drive so that all of the data can be copied without loss.

However, not all hard drives have identical storage capacity, even when they are

all labeled identically in terms of GB size. Thus, by enabling the size tolerance, the

system will allow the target hard drive’s capacity to be less than the original hard

drive by the percentage specified at the risk of less data loss/corruption.

8) Startup Menu

This setting will allow you to choose which menu you would like to see first when

you turn on the system.

9) Partition Mode

This setting will allow you to copy only the valid partitions of the source hard drive

(along with MBR/GPT table) bit by bit.

6. Utilities

1) Compare

This function will perform the data comparison process between the source and

target hard drive to ensure data accuracy.

2) Verify Disk

This function will scan all target hard drives for readability.

3) Measure Speed

This function will perform read and write testes to report the read speed for the

source hard drive and write speed of all target hard drives.

4) Device Info

This function will show information regarding the hard drive connected to the

system.

5) System Info

This function will show the system’s hardware & software information.

6) Load Default

This function will reset all of the options back to the manufacture’s default settings.

Perform this function if the system is acting abnormal. Perform the “Shutdown”

operation and restart the system in order for these changes to take effect.

7) Update Firmware

This function will update the software for the system. The update file needs to be

transferred to a Hard Drive pre-formatted as “FAT32” file system on a PC.

There are two options for this function:

Format Update HDD: This function will prepare a hard drive to be eligible for

firmware-update by format such hard drive in the source port as FAT16/32 File

System.

Update: This function will perform firmware-update with the firmware-update

hard drive that contains the firmware update file.

General Firmware Update Procedure:

a. Pre-format a SATA Hard Drive using “Format Update HDD” function.

b. Copy the manufacture certified update file onto such pre-formatted hard

drive via a PC/Mac.

c. Insert such hard drive into the Source Port of the system.

d. Execute the “Update” function.

e. Restart the system when asked to do so.

It is strongly suggested that an upgrade to the system’s firmware not be performed,

unless the system is getting unstable and instructed to do so by a technician.

8) Save

This function will save all the settings modified since the last time the system was

booted-up.

7. Manage Accounts

This menu will allow the Administrator to perform the following user administrative tasks.

This feature is disabled by default. Prior to activating this feature, the duplicator recognizes

all users as the only activated user defined as the administrator. The pre-defined password

for this menu is “0000”.

1) View User

This menu allows for the viewing of the existing user accounts.

2) Create User

This menu allows for the creation of additional user accounts. Each user has

individual settings. During this process, there are prompts to enter a new user

name (up to 8 alphanumeric letters or numbers) and user password (consisting of

a 4-digit number) for a new account.

3) Delete User

This menu allows for the deletion of an existing user account. During this process,

there is a prompt to select the existing account to be removed.

*User “Admin” is the administrative account; this account CANNOT be deleted.

4) Password on Bootup

This menu allows for the enabling/disabling pf the user administrative feature

prompt; user login upon boot up.

8. Shutdown

This function saves any system settings that have be modified since powering on the

system, to makes sure it is safe to turn off the system without any loss of settings. Once

the Ready to Power OFF message appears, then the system can be safely turned off via

the machine Power Switch. Turning off the system without performing this function will

increase the risk of damaging the system.

Inhaltsverzeichnis

Andere Vinpower Disc-Duplikator Handbücher

Vinpower

Vinpower SharkCopier Bedienungsanleitung

Vinpower

Vinpower ROBOTIC AUTOLOADER V3.5 Bedienungsanleitung

Vinpower

Vinpower TITAN SUPREME Bedienungsanleitung

Vinpower

Vinpower Hard Drive V 1.0 Bedienungsanleitung

Vinpower

Vinpower The Cube V3.6.0 Bedienungsanleitung

Vinpower

Vinpower Daisy Chain Bedienungsanleitung

Vinpower

Vinpower SharkCopier SATA Bedienungsanleitung

Vinpower

Vinpower TITAN lite Bedienungsanleitung

Vinpower

Vinpower ROBOTIC AUTOLOADER V3.6.0 Bedienungsanleitung

Vinpower

Vinpower The Cube V3.6.0 Bedienungsanleitung

Vinpower

Vinpower VENSOLPTR Bedienungsanleitung

Vinpower

Vinpower Flash Memory V 2.1 Bedienungsanleitung

Vinpower

Vinpower THE CUBE SERIES Bedienungsanleitung

Beliebte Disc-Duplikator Handbücher anderer Marken

Riso

Riso CV Series Handbuch

MicroBoards Technology

MicroBoards Technology GX-2 Bedienungsanleitung

Addonics Technologies

Addonics Technologies HDUS325DX Bedienungsanleitung

Carry

Carry Pro118 Bedienungsanleitung

CopyPro

CopyPro PowerPro II Bedienungsanleitung

Primera

Primera Max Bedienungsanleitung

Logicube

Logicube EchoPlus-NG Bedienungsanleitung

Silca

Silca Delta 2000 SA Bedienungsanleitung

Reflex7

Reflex7 Daisy Chain Series Bedienungsanleitung

Vinpower Digital

Vinpower Digital SharkCopier DC Bedienungsanleitung

Codonics

Codonics Virtua E Bedienungsanleitung

Octave

Octave Copy Master II Bedienungsanleitung

Kanguru

Kanguru U2-DVDDUPE-S Bedienungsanleitung

StarTech.com

StarTech.com 8STSATDUP11 Bedienungsanleitung

DUPLO SEIKO CORPORATION

DUPLO SEIKO CORPORATION Duprinter DP-460 Bedienungsanleitung

Addonics Technologies

Addonics Technologies UDFH7 Bedienungsanleitung

Vinpower Digital

Vinpower Digital MiniLoader VDX-1 Bedienungsanleitung

Addonics Technologies

Addonics Technologies CFASTD5 Bedienungsanleitung