VIP INTIPRDSG (GEN 3) Bedienungsanleitung

Residential & Apartment

Intercom Systems

Installation Manual

Supports models from:

INT-Q1-22

VIP Vision Intercom Installation Manual - Version: INT-Q1-22

1. Pre-Installation

1.1 Please Read Before Installation 4

1.2 Device Models & General Use 5

2. Wiring & Connections

2.1 Connection Diagrams - Door Stations 7

2.2 Connection Diagrams - Indoor Monitors 11

2.3 Door Strike Wiring 12

2.4 Intercom Wiring 13

3. Intercom Setup

3.1 One Key Conguration 16

3.2 Manual Conguration of a Residential Intercom System 19

3.3 Manual Conguration of an Apartment Intercom System 26

3.4 Re-conguring an Existing Intercom for Use on the Network 32

4. Additional Conguration

4.1 Adding IP Cameras to an Indoor Monitor 33

4.2 Adding Your Door Station to a VIP Vision NVR 34

4.3 Issuing Cards (For Door Stations with a Built-In Card Reader) 35

4.4 Adding Entry Codes (For Door Stations with a Built-In Keypad) 36

4.5 Setting Time & Date 37

4.6 Changing Door Station Video & Audio Settings 37

4.7 Door Station Latch Timing 38

4.8 Adjusting Monitor Audio Settings 38

4.9 Changing the IP Address of a Windows Computer 39

4.10 Finding Available IP Addresses 41

4.11 Using Cong Tool to Find & Initialise Devices on a Windows Computer 42

4.12 Initialising Devices With Cong Tool 42

4.13 Modify Device IP Addresses with VDP Cong Tool 43

Table of Contents

Visit help.c5k.info for more information and support

Table of Contents

5. Mobile App

5.1 Remote Access for Residential Systems 44

5.2 Push Notications 45

5.3 Apartment Intercom Remote Access 45

6. Using the Intercom System

6.1 Making and Answering Calls 46

6.2 Taking Videos / Snapshots from the Indoor Monitor 46

6.3 Viewing Your Videos/Snapshots from the Indoor Monitor 46

6.4 Calling Between Indoor Monitors 47

6.5 Create Favourites 47

7. Troubleshooting

Factory Reset Intercom Devices 48

VIP Vision Intercom Installation Manual - Version: INT-Q1-22

1. Pre-Installation

Thank you for purchasing this Intercom System. This install guide

covers basic setup, installation and use of your intercom system.

For detailed technical support and software downloads, visit our

Help Centre at: help.c5k.info

help.c5k.info

• Settings password is user congured upon initial setup, it can be

entered after holding the Settings button for 6 seconds.

• Door Station’s default IP address is 192.168.1.108

• The Door Station’s username is “admin” and the password is

user congured upon initial setup. Please note that only the Door

Station has a web interface - the Indoor Monitor does not.

• If this is your rst time purchasing a VIP Residential IP Intercom,

we recommend setting it up on the bench before installation, to familiarize yourself with the

product. Upon installation, we recommend bringing a laptop to site to make any settings

changes that may be required. An understanding of basic computer networking is required.

• The IP intercom requires a CAT5e/CAT6 cable to be run between the Indoor Monitor and

Door Station. The cable must be terminated to TIA-568A or TIA568B standards. If you wish to

connect to the system remotely, your Indoor Monitor and Door Station must be connected to

your modem or network switch (sold separately) via a CAT5e/CAT6 cable.

• Power must be provided to each Door Station and Indoor Monitor - this can be done via Power

other Ethernet with a PoE switch, or via a separate DC power supply. Alternatively, 2-Wire

cabling can be used (available on select models only).

IMPORTANT:

• Door Stations are designed to mounted in a sheltered location, not exposed directly to weather.

• When installing the Door Station, apply outdoor silicone sealant between the Door Station and

the wall, and seal the hole that has been created for the cable to prevent water ingress. If using

a mounting box, ensure the box is also sealed, and the included waterproof rubber seals are

used when installing the screws.

1.1 Please Read Before Installation

Visit help.c5k.info for more information and support

Single Call-button IP Door Stations

Image

Model INTIPRDSG (GEN 3) INTIPRDSG-P INTIPRDSJ INTIPRDSD

Features 2-Wire & IP

12V Out for Relay/INTIPDM

IP Only

12V Out for Relay/INTIPDM

IP Only

Card Reader

IP Only

Card Reader

Keypad for Unlock

12V Out for Relay/INTIPDM

Max Additional

Door Station 20 20 20 20

Max Monitors 10 10 10 10

Power DC 48V

1A, POE

DC 12V-24V

1A, POE

DC 12V

1A, POE

DC 12V

1A, POE

Remote Access Yes Ye s Yes Ye s

Multiple Call-button & Apartment IP Door Stations

Image

Model INTIPDDS2 INTIPDDS4 INTIPADSD

Features

IP Only

2 Call-buttons

Card Reader

IP Only

4 Call-buttons

Card Reader

IP Only

Card Reader

Keypad for Calling/Unlock

12V Out for Relay/INTIPDM

Max Additional

Door Station 20 20 10

Max Monitors 10 10 200

Power DC 12V 1A, POE DC 12V 1A, POE DC 12V 2A, POE

Remote Access Yes (One QR code per Main Monitor) Yes (One QR code per Main Monitor) N/A

1.2 Device Models & General Use

VIP Vision Intercom Installation Manual - Version: INT-Q1-22

1.2 Device Models & General Use

Indoor Monitors & Accessories

Image

Model INTIPMONGW

INTIPMONGB INTIPMONGBL INTIPMONDWH2

INTIPMONDBH2 INTIPMON INTIPDM

Features 7’’ IP Monitors 10’’ IP Monitors 7’’ IP Handset Monitors 7” IP Monitor Door Expansion Module

Power 12VDC / PoE 12VDC / PoE 12VDC / PoE 12VDC / POE (Requires

INTIPMONPOE) 12VDC

GEN.3 2-Wire

INTIPRDSG(GEN.3) INTIPMON2W2 INTIPPOE2W2

2-Wire & IP

12V Out for Relay/INTIPDM 7” 2-Wire Monitor 2-Wire Network

Controller

Power via INTIPPOE2W Power via INTIPPOE2W 48VDC

Visit help.c5k.info for more information and support

2.1 Connection Diagrams - Door Stations

2. Wiring & Connections

2.1.1 INTIPRDSG, INTIPRDSG-P & INTIPRDSG (GEN.3) - G Series Residential Door Station

INTIPRDSG(GEN.3)INTIPRDSG-P

Name Description

Ethernet Port Power over Ethernet & network connectivity

Reset Button Reset conguration back to factory default settings

Tamper Switch The Door Station will generate an alarm sound if it is being removed from the wall

8-Pin

Connector

EOC1 (GND) (INTIPRDSG Only) 12V DC negative input/2-Wire connection port

2-wire-(GND) (INTIPRDSG GEN.3 Only) 48V DC negative input/2-Wire connection port

GND (INTIPRDSG-P Only) 24V DC negative input

EOC1 (+12) (INTIPRDSG Only) 12V DC positive input/2-Wire connection port)

2-wire-(48V) (INTIPRDSG GEN.3 Only) 48V DC positive input/2-Wire connection port

+24V (INTIPRDSG-P Only) 24V DC positive input

ALARM_COM Alarm common comtact

ALARM_NO Alarm normally open contact

RS485A For use with the INTIPDM

RS485B For use with the INTIPDM

12V_OUT 12V DC positive output, 100ma max current. For use with the INTIPDM

GND Ground connection for 12V_OUT

6-Pin

Connector

DOOR_NO Door relay normally open contact

DOOR_COM Door relay common contact

DOOR_NC Door relay normaly closed contact

GND Ground connection for DOOR_FB or DOOR_BUTTON

DOOR_FB Door latch feedback input, for use with monitored door latch

DOOR_BUTTON Exit button dry contact input, triggers door relay when shorted to GND

VIP Vision Intercom Installation Manual - Version: INT-Q1-22

2.1 Connection Diagrams - Door Stations (cont.)

2.1.2 INTIPDDS2 & INTIPDDS4 - Residential Door Stations

Name Description

Ethernet Port Power over Ethernet & network connectivity

12-Pin

Connector

12V 12V DC positive input

GND 12V DC negative input / Ground connection for FEEDBACK or Unlock

NO Door relay normally open contact

COM Door relay common contact

NC Door relay normally closed contact

FEEDBACK Door latch feedback input, for use with monitored door latch

UNLOCK Exit button dry contact input, triggers door relay when shorted to GND

RS485A For use with the INTIPDM

RS485B For use with the INTIPDM

ALM_IN Alarm input contact

ALM_NO Alarm normally open contact

ALM_COM Alarm common contact

Visit help.c5k.info for more information and support

2.1 Connection Diagrams - Door Stations (cont.)

2.1.3 INTIPRDSJ - J Series Residential Door Station

Name Description

Ethernet Port Power over Ethernet & network connectivity

Reset Button Reset conguration back to factory default settings

Tamper Switch The Door Station will generate an alarm sound if it is being removed from the wall

12-Pin

Connector

12V 12V DC positive input

GND 12V DC negative input

NO Door relay normally open contact

COM Door relay common contact

NC Door relay normally closed contact

FEEDBACK Door latch feedback input, for use with monitored door latch

UNLOCK Exit button dry contact input, triggers door relay when shorted to GND

GND Ground connection for FEEDBACK or UNLOCK

RS485A For use with the INTIPDM

RS485B For use with the INTIPDM

N/A Not used

VIP Vision Intercom Installation Manual - Version: INT-Q1-22

Name Description

Ethernet Port Power over Ethernet & network connectivity

Reset Button Reset conguration back to factory default settings

Tamper Switch The Door Station will generate an alarm sound if it is being removed from the wall

12-Pin

Connector

DC_IN 12V DC positive input

GND 12V DC negative input

ALM_OUT_NO Alarm output normally open contact

ALM_OUT_COM Alarm output common contact

GND Ground contact to be used with ALM_IN

ALM_IN Alarm input contact

NO Door relay normally open contact

COM Door relay common contact

NC Door relay normally closed contact

GND Ground connection for SR or PUSH

PUSH Exit button dry contact input, triggers door relay when shorted to GND

SR Door latch feedback input, for use with monitored door latch

8-Pin

Connector

12V_OUT 12V DC positive output, 100ma max current (for use with the INTIPDM)

GND Weigand card reader ground connection

WG_D1 Weigand card reader D1 connection

WG_D0 Weigand card reader D0 connection

WG_LED Weigand card reader LED connection

GND Ground connection for 12V_OUT

RS485B For use with the INTIPDM

RS485A For use with the INTIPDM

2.1 Connection Diagrams - Door Stations (cont.)

2.1.4 INTIPADSD - Apartment Series Door Station

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere VIP Gegensprechanlage Handbücher

VIP

VIP INTIPRKIT Bedienungsanleitung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Videx

Videx VIDEOKIT Series Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung

Bticino

Bticino Classe 300 Bedienungsanleitung

LG L5142 Bedienungsanleitung