Viper AS710R Bedienungsanleitung
Electronic Service
Manuals
This electronic document is provided as a service to our customers.
Wedonotcreatethecontentsoftheinformationcontainedinthisdocu-
ment. Shouldyouhavedetailedquestionspertainingtotheinformation
contained in this document, you may contact Michco, or the manufac-
turer which provided the original information in this electronic deliver-
able. Michco’sonlypartin this electronic deliverable was the electronic
assemblyprocess. Byprovidingthismanualonlinewearenotguaran-
teeing parts availability.
You may contact Michco through the following methods:
Phone (517) 484-9312 or (800) 331-3339
2011 N. High St. -- Lansing, Michigan -- 48906
Fax: (517) 484-9836
Email: [email protected]
Web site: www.Michco.Com
Parts Web site: www.FloorMachineParts.Com
Order Parts on Line at:
www.FloorMachineParts.Com
Directly to Parts & Service:
By Fax: (517) 702-2041
By Voice: Use numbers above.
Serving the Cleaning Industry Since 1922
Notice: All copyrighted material remains property of original owners, all trademarks are property of respective owners.
ManualsaresubjecttoManufacturer’sreproductionlimitations. Originalsorreproductionswereprovidedbymanufacturers
through a request. We make no warranty as to the correctness of information provided in this document and you assume
allrisk. By placing thesemanualsonlinewe are notdeclaringourcorporation to be anmanufacturerauthorizeddealer or
provider, please check ourwebsiteforauthorizedmanufacturerswerepresent.
Ride-on Scrubbers
USER MANUAL
READ USER MANUAL CAREFULLY BEFORE USE
Please fill out & return your warranty card
VR10029 REV.02
2016-1-13
Model #
Serial No.#
1
Machine destription
Machine structure
A1 --Seat (with Safety button)
A2 -- Recovery tank lid
A3 -- Recovery tank
A4 -- Solution tank
A5 -- Squeegee
A6 -- Adjust nut of brush skirt
A7 -- Brush skirt
A8 -- Brushes
A9 -- Drive motor
A10--Foot pedal of brush lift or low
A11--USB port for phone charging
A12--Front housing
A13--Control panel
A14--Steering wheel
A15--Emergency-stop button
A16--Net bag
B1 -- Squeegee pressure adjustment knob
B2 -- Squeegee fixing knob
B3 -- Vacuum hose inlet
B4 -- Rear squeegee latch
C1 -- Drain hose
C2 -- Recovery tank turn latch
C3 -- Charging cable storage
C4 -- Clean water inlet
C5 -- Squeegee lift lever
C6 -- Drive pedal
C7 -- Water level sight tube
C8 -- Batteries
D1 -- Drain cover
D2 -- Water valve
D3 -- Filter
E1 -- LED display
E2 -- Recovery tank full indicator
E3 -- The brush on/off button
E4 -- Drive motor indicator
E5 -- Key switch
E6 -- Speed potentiometer
E7 -- Forward/reverse button
E8 -- Clean water flow control button
E9 -- Horn
E10--Solution tank empty indicator
E11--Battery capacity indicator
F1 -- Charging port
F2 -- Charging LED indicator
F3 -- Circuit breaker
Figure A
Figure B
Figure C
Figure D
EFigure
F
Figure
USER MANUAL
5
SAFETY PRECAUTIONS
This machine is intended for commercial use. It is constructed for use in an indoor environment
and is not intended for any other use. Use only with recommended accessories.
All operators shall read, understand and exercise the following safety precautions:
1) DO NOT OPERATE MACHINE:
Unless trained and authorized.
Unless you have read and understand the user manual.
In flammable or explosive areas.
If not in proper operating condition.
In outdoor areas.
2) BEFORE OPERATING MACHINE:
Make sure all safety devices are in place and operate properly.
3) WHEN USING MACHINE:
Go slow on inclines and slippery surfaces.
Follow all safety guidelines.
Be very careful when using the machine in reverse.
Report and repair any damage to machine prior to operating it.
4) BEFORE LEAVING OR SERVICING MACHINE:
Never park the machine on a slope.
Turn machine off.
5) WHEN SERVICING MACHINE:
Read user manual thoroughly prior to operating or servicing this machine.
Use manufacturer supplied or approved replacement parts.
Use approved jack or hoist to safely elevate the machine.
Disconnect batteries prior to working on machine.
Wear gloves when handling batteries or battery cables.
Avoid moving parts. Do not wear loose fitting clothing while servicing machine.
6）SAFETY DEVICES
Emergency-stop button(A15)
When the Emergency-stop button is pressed, the machine will come to a sudden
stop, and all machine functions and displays will stop. Twist the button slightly to
reset it.
Seat safety button (inside A1).
If the operator leaves the seat during operation, the drive motor will shut off in 0.5
seconds. The LED screen displays STOP.
USER MANUAL
6
WARNING Indicates a potential risk of injury or dangerous situation with risk of
death for the operator.
NOTED Indicates a remark related to important or useful functions.
MACHINE SET UP & INSTALLATION
UNPACKING MACHINE
Be sure and check packing carton for any damage. Report immediately any damage to carrier.
Check contents of package to ensure that the following items are included:
1, Machine
2, Squeegee assembly
3, Brush assembly(x2)
4, User manual
5, Battery charger (If equipped)
6, Batteries (x4) (If equipped)
7, Connecting wire for battery and charger (If equipped)
8, Warning lamp (If equipped)
9,Bumper bracket(If equipped)
BATTERY CONNECTIONS
1. Turn off the key switch (E5).
2. Flip the seat (A1) to the open position, use the latch (C2) and open the battery
compartment. If the machine does not include batteries, contact your distributor for
recommended batteries.
After selecting batteries, please choose WET or GEL mode with toggle switch on the back of
PCB, as shown in the figure below.
USER MANUAL
7
3. Carefully place the four batteries into the compartment as shown in figure below. Place the
battery brace at the front of the four batteries.
4. Connect battery cables to posts in numbered order as shown in the figure below.
5. Apply a coat or protective spray on the cable connections to prevent battery corrosion.
6. Cover recovery tank and seat.
Make sure the recovery tank is empty when opening it.
Do not drop batteries into compartment. Do not put metal on the batteries.
Never connect + to +, or - to - , never connect + to – with single battery, when
disassembling or installing the batteries.
MACHINE SET UP
PRE-OPERATION CHECKS
1. Sweep or dust mop the surface to be cleaned.
2. Check battery meter to make sure batteries are fully charged. (see BATTERY CHARGING)
3. Check that brush / pad is properly installed.
4. Check that squeegee is properly installed.
5. Check the speed driver (A9) is work normally.
6. Make sure the recovery tank is empty. If not, drain it.
7. Make sure solution tank water indicator (E10) is not on. If on, fill water in solution tank (A4).
8. Check that the water valve (D2) is not indicated “0”.
INSTALLING PAD DRIVER OR BRUSH
1. Ensure that the machine is turned off (E5).
2. Raise the brush head (A7) off the floor by depressing the front of foot pedal (A10) on the left
of machine.
3. Put brushes (A8) below both brush driver motor hub.
4. Lower the brush deck (A7) by depressing the rear of foot pedal (A10). While sitting on the
machine, turn on the brush switch (E3) insure the speed control knob (E4) is set to minimum.
Lightly depress driver pedal (C6), and the brush motors will turn on. The brushes should
attach to the machine automatically.
USER MANUAL
8
5. Adjust the nut (A6) to properly position the splash guards.
Never work without the brusher/pad perfectly installed.
When cleaning or replacing the brushes, you should raise the brush head and rotate
the reverse direction to “working” direction quickly. The two brushes are reverse in
direction.
INSTALLING AND ADJUSTING THE SQUEEGEE
1. Ensure that the machine is turned off (E5).
2. Turn the squeegee lift lever (C5) to put down the squeegee bracket (A5) on floor.
3. Loosen the two knobs (B2) on the squeegee and slide the squeegee into the slots in the back
of the squeegee bracket.
4. Tighten the knobs(B2) securely.
5. Secure the vacuum hose (B3) on the pick-up tube of the squeegee.
6. Adjusting the nut (B1) to properly set the squeegee angle.
FILLING THE SOLUTION TANK
1. The solution fill hose is under the seat(C4).
2. Do not overfill the solution tank. Leave at least two inch from the opening of tank.
3. Water temperature should not exceed 40°C/104°F.
Use only low-foam and non-flammable detergents suitable for ride-on scrubber
applications.
Each time that you need to fill the solution tank, always empty and clean the recovery
tank by removing the drain hose plug (C1). After each use, unscrew the drain cap (D1) to
drain solution tank.
CHECKING THE SPEED DRIVER
1. Sit on seat (A1) of the machine.
2. Turn on the key switch (E5).
Depress the front,
Brushes up
Depress the rear,
Brushes down
Andere Handbücher für AS710R
3
Inhaltsverzeichnis
Andere Viper Schrubber Handbücher
Viper
Viper 50000532 Bedienungsanleitung
Viper
Viper TP24TSCRUB Bedienungsanleitung
Viper
Viper AS430C Bedienungsanleitung
Viper
Viper AS430C Bedienungsanleitung
Viper
Viper AS6690T Bedienungsanleitung
Viper
Viper 50000398 Bedienungsanleitung
Viper
Viper AS430C-US Bedienungsanleitung
Viper
Viper AS380/15C-EU Bedienungsanleitung
Viper
Viper AS530R Bedienungsanleitung
Viper
Viper FANG 18 C Bedienungsanleitung
Viper
Viper AS430C Bedienungsanleitung
Viper
Viper AS1050R Benutzerhandbuch
Viper
Viper AS1050R Benutzerhandbuch
Viper
Viper FANG 18 C Bedienungsanleitung
Viper
Viper AS510B Bedienungsanleitung
Viper
Viper AS430B Bedienungsanleitung
Viper
Viper Fang 24T Bedienungsanleitung
Viper
Viper AS710R Bedienungsanleitung
Viper
Viper TP24TSCRUB Bedienungsanleitung
Viper
Viper Fang15B Bedienungsanleitung
