Visonic TOWER CAM PG2 TOWER CAM PG2 Bedienungsanleitung

D-304493 TOWER CAM PG2 Installation Instructions 1

TOWER CAM PG2

TOWER CAM PG2TOWER CAM PG2

TOWER CAM PG2

PowerG, Outdoor Mirror PIR Motion Detector with Anti-

masking and Built-In Camera

Installation Instructions

1. INTRODUCTION

1. INTRODUCTION1. INTRODUCTION

1. INTRODUCTION

The TOWER CAM PG2 is a 2-way, wireless outdoor digital mirror PIR

detector with built-in camera. Activated upon PIR detection or upon

demand, the TOWER CAM PG2 sends clear images to the Monitoring

Station for alarm image verification.

The PIR motion detector’s features are as follows:

•

Operates with PowerMaster control panels

(version 18 and higher)

•

Patented 8 independent quad PIR detectors (Octa-QUAD



)

operating in true Quad configuration (patented) with true motion

recognition (TMR) processing for each of the 8 PIR detectors.

•Advanced Obsidian Black MirrorTM optics (patent pending).

•Optimum performance even in poor weather conditions such as snow,

rain, dust, wind and direct sunlight

•Tamper protection prevents opening and removal from wall

•PowerG two-way Frequency Hopping Spread Spectrum FHSS-

TDMA technology - provides robustness and reliability

•Built-in link quality indicators enable installer to check signal quality

without physically approaching the control panel.

•Robust housing with recessed window.

•Smart anti masking distinguishes between masking spray and rain.

•Alarm LED is visible in sunlight.

•Automatic termination of walk-test after 15 minutes.

•Microprocessor-controlled temperature compensation.

•Immunity to pets weighing up to 18 Kg (40lb) – see Table 1

•Built-in swivel bracket

The camera’s features are as follows:

•Up to 10 cameras can be enrolled

•Images multiplexed from all enrolled cameras

•Color and black & white images

•Auto-setup

•Camera tuning by simple walk-test

•Day and night CMOS camera, with near IR illumination. This allows

taking pictures in full darkness without letting the intruder know.

•Instant capture: guarantees capture of fast moving intruder.

•Optional AC power

•An event records 2 images per second. 10-15 images total

Notes:

1. For UL/ULC installation, the camera feature is not to be enabled in UL

listed product.

2. Pet immunity is not evaluated by UL/ULC.

A. IR LEDs B. Indication LED C. Camera

D. External power LED E. Alarm LED

Figure 1. External View

. .

. INSTALLATION

INSTALLATIONINSTALLATION

INSTALLATION

2.1 Installation

A. Bracket installation (see Figure 2). Fix the bracket firmly on a stable wall or pillar. The orientation of the fixed bracket must be as parallel as

possible to the surveyed ground surface.

B. Adjust the detector's horizontal and vertical angles (see Figure 3), according to the surveyed ground surface. The vertical angle indicator

position for various installation height and coverage distance combinations is detailed in Table 1. (The information refers to a relatively flat

surveyed area. Verify the correct installation by walk-test.)

C. Fasten the detector to the bracket (see Figure 2 step 4).

Table 1 - Vertical Adjustment Reference

Mounting Height Coverage Distance

2m / 6.7ft 4m / 13ft 6m / 20ft 8m / 26ft 10m / 33 ft 12m / 39 ft

3.0m / 10 ft

2.5m / 8 ft

2.0m / 7 ft

1.5m / 5 ft

2 D-304493 TOWER CAM PG2 Installation Instructions

Notes:

1. For UL/ULC listed installations the following setting is required when mounting at a height of 8ft:

2. For UL/ULC listed installations the maximum range of the detection is 10m/33ft”.

3. The grayed-in cells in Table 1 are the installation options recommended for reducing the probability of false alarms from pets.

Event counter: One region

Correct Installation

Incorrect Installation

A. Mark drilling point

B. Screw hole for wall tamper C. Drill

D. Fasten E. Three long screws F. Two short screws

Note: The 2 screw holes enable adjustment of the bracket on the wall, if needed, following the walk test.

Figure 2 - Installation

HORIZONTAL ADJUSTMENT (-45°

°°

°to +45°

°°

°)

VERTICAL ADJUSTMENT (0°

°°

°to -10°

°°

°in 2.5°

°°

°clicks / steps)

D-304493 TOWER CAM PG2 Installation Instructions 3

Installation Notes:

The top cover should only be accessed by authorized service personnel or manufacturer. Do not obscure the detector field of view with large objects. Install

in position such that expected intruder motion is perpendicular to the zones of detection.

Alarms triggered by conditions such as weather, blowing leaves and brush, or related environmental conditions, etc., need to be considered when assessing

the installation and application. It is recommended that the intrusion detection unit is not to be connected to an alarm initiating circuit but may be connected

to a trouble alarm circuit if nuisance trips are not tolerable.

COVER CLOSURE

1. Release locking 2. Adjust 3. Lock 4. Release locking 5. Adjust

6. Lock 7. Turn cover and push slider 8 & 9. Put back cover 10. Secure with screw

A. Vertical angle steps

Figure 3 - Adjustment and Cover Closure

2.2 Battery Insertion

It is recommended to perform the first batteries insertion on a flat surface (see Figure 4). After battery insertion, the LED will flash for 60

seconds and then the detector will enter a 15 minutes' local diagnostic mode.

4 D-304493 TOWER CAM PG2 Installation Instructions

A. Tamper switch B. Press firmly to release the bracket C. 1 screw

Steps 7 and 8 are optional for external 7.5 VDC power connection

D. Snap the terminal block into place.

Caution!

Risk of explosion if battery is replaced by an incorrect type. Dispose of used battery according to the manufacturer's instructions.

Caution! The battery used in this device may present a risk of fire or chemical burn if mistreated. Do not disassemble, heat above 66°C, or

incinerate. Replace battery with CR17450 Lithium batteries manufactured by EVE only. Dispose of used battery promptly. Keep away from

children. Do not disassemble and do not dispose of in fire.

Note: Tamper protection is mandatory for UL burglary installations.

Figure 4 – Battery Insertion

D-304493 TOWER CAM PG2 Installation Instructions 5

2. . Enrollment

Refer to the PowerMaster control panel's Installer Guide and follow the procedure under the "02:ZONES/DEVICES" option of the Installer Menu.

A general description of the procedure is provided in the following flow chart.

Step 1 Step 2 Step 3 Step 4

Enter the Installer menu and select

“02:ZONES/DEVICES”

Select "ADD NEW DEVICE"

See Note 1

Enroll the device (see Figure 5) or

enter the device ID

Select a detector number for

the new detector

02:ZONES/DEVICES 

ADD NEW DEVICES





ENROLL NOW or

ENTR ID:XXX-XXXX



Z09:Motion Camra

ID No. 142-XXXX



MODIFY DEVICES

Step 5 Step 6 Step 7

Configure Location, Zone Type &

Chime parameters

Enter PARTITIONS.

See Note 2

Assign partitions to the detector by

pressing the ,

and/or buttons on the

panel

Z09.LOCATION

Z09.ZONE TYPE

Z09.SET CHIME

Z09/PARTITIONS Z09:P1



P2 P3



means scroll and select

Notes:

[1] If the detector is already enrolled you can configure the detector parameters and assign partitions via the “Modify Devices” option – see

Step 2.

[2] PARTITIONS will appear only if PARTITIONING was previously enabled in a panel that supports the Partitioning feature (for further details,

see "Partitioning" in the PowerMaster Installer Guide).

2.4. Configuring the Detector Parameters

Enter the DEVICE SETTINGS menu and follow the configuration instructions for the TOWER CAM PG2 PIR detector as described below.

Option Configuration Instructions

ALARM LED Define whether or not to activate the alarm LED indication.

Optional settings: ON (default) and OFF.

PIR SENSITIVITY Define if the detector operates at regular or high PIR sensitivity, or that at least one detection zone must be crossed

before an alarm is triggered (One Region).

Optional settings: LOW (default), HIGH and One Region.

Note: For EN and UL compliance, the detector should be set to "One Region".

DISARM ACTIVITY Define whether or not to set the activity time during Disarm mode.

Optional settings: NOT Active (default), YES – no delay, YES + 5s delay, YES + 15s delay, YES + 30s delay, YES +

1m delay, YES + 2m delay, YES + 5m delay, YES + 10m delay, YES + 20m delay and YES + 60m delay.

OUTDOOR ANTI-M

Enable or disable the outdoor anti-masking feature.

Optional settings: Disabled (default) and Enabled.

ALARM Hours Define whether motion alarms are always enabled or only when dark (at night).

Optional settings: Day and Night (default) and Night only.

Note: For UL/ULC installation, the Alarm Hours feature when enabled for night protection should only be used as

supplemental protection to the protection covering the protected area.

IMAGE COLOR

Define whether the image will be in black & white or color.

Optional settings: Black & White (default) and Color.

IMAGE RESOLUTION Set the pixel quality of the image. Select 160 x 120 for lower quality or 320 x 240 for higher quality.

Optional settings: 320 x 240 (default) and 160 x 120.

IMAGE QUALITY

Set the quality of the image.

Optional settings: High (default) and normal.

IMAGE BRIGHTNESS

Set the brightness of the image.

Optional settings: Normal (default) -3, -2, -1, +1, +2 and +3.

IMAGE CONTRAST

Set the contrast of the image.

Optional settings: Normal (default) -3, -2, -1, +1, +2 and +3.

6 D-304493 TOWER CAM PG2 Installation Instructions

2.5 Local Diagnostic Test

A. Set the detector in local diagnostic mode, as follows:

Open the detector’s bottom cover (see Figure 4, steps 1 - 3) and then press and release the tamper switch (see Figure 5). The LED will flash

for 60 seconds and then the detector will enter into 15 minutes' local diagnostic mode.

Note: The detector automatically enters into 15 minutes' local diagnostic mode after battery installation or Tamper switch recovery.

B. Adjust the detector in the horizontal plane to cover the required protected area.

C. Walk into the detectors’ field of view. Adjust the vertical plane to receive the maximum number of detections when crossing the entire 90°

pattern. Verify that the LED blinks each time your motion is detected, as you cross one Quad PIR. Then verify that the LED lights steadily

for 2 seconds as you cross the next adjacent Quad PIR. After alarm indication, the LED blinks three times and provides the received

signal strength indication (see Table 2).

Table 2 – Received Signal Strength Indication

LED response Reception

Green LED blinks Strong

Orange LED blinks Good

Red LED blinks

Poor

No blinks

No communication

IMPORTANT! Reliable reception must be assured. Therefore, "poor" signal strength is not acceptable. If you receive a "poor" signal from the

detector, re-locate it and re-test until a "Good" or "Strong" signal strength is received.

Note: For detailed Diagnostics Test instructions refer to the control panel Installer's Guide

The LED blinking, described above, is operative only in Local diagnostic mode. Upon each full detection (LED lights steadily for 2 seconds), the

control panel receives the alarm. If required, perform the detector's horizontal / vertical adjustments (see section 2.1 and Figure 3).

Important! Instruct the user to perform a walk test at least once a week, to verify proper operation of the detector.

D. Place a piece of cardboard on the detector’s front side to deliberately mask the optical window. Verify that after 2 minutes, the yellow LED

lights continuously (see Table 3 below) and the alarm control panel receives the masking alarm.

E. Remove the masking from the detector’s front side. Verify that the LED turns off after 30 seconds.

Table 3 - LED operation

LED Indications Event

Red Alarm LED blinks Stabilization (warm-up 60 sec)

Red Alarm LED ON 0.2 sec. Tamper open / close

Red Alarm LED blinks twice One quad PIR detection in diagnostic mode

Red Alarm LED on 2 sec. Intruder alarm

Yellow Indication LED on AM detection – diagnostic mode

Yellow indication LED blinks slowly (0.2 sec. ON, 30 sec. OFF) AM detection – Normal mode

A. Alarm LED

B. Indication LED

C. Enroll button

D. Tamper switch

Figure 5. TOWER CAM PG2

D-304493 TOWER CAM PG2 Installation Instructions 7

. COMPLIANCE WITH STANDARDS

Compliance with Standards

The TOWER CAM PG2 is designed to comply with the following standards:

Europe (CE): EN 300220, EN 301489, EN 60950, EN 50130-4, EN 50130-5, EN 50131-2-2, EN 50131-6,

EN 50131-1 Grade 2 Class IV

The TOWER CAM PG2 is compatible with the RTTE requirements - Directive 1999/5/EC of the European

Parliament and of the Council of 9 March 1999 and EN50131-1 Grade 2 Class IV.

UK: This product is suitable for use in systems installed to conform to PD6662:2010 at Grade 2 and

environmental class 4. DD243 and BS8243

USA: CFR 47 Part 15 (FCC), UL-639

Canada: RSS 210

The Power G peripheral devices have two- way communication functionality, providing additional benefits as described in

the technical brochure. This functionality has not been tested to comply with the respective technical requirements and

should therefore be considered outside the scope of the product’s certification.

EN 50131-1 Security Grade Grade 2

EN 50131-1 Environmental Class Class IV

FCC Compliance Statement

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference in residential installations. This equipment generates uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio and

television reception.

However, there is no guarantee that interference will not occur in a particular installation. If this device does cause such interference, which can

be verified by turning the device off and on, the user is encouraged to eliminate the interference by one or more of the following measures:

– Re-orient or re-locate the receiving antenna.

– Increase the distance between the device and the receiver.

– Connect the device to an outlet on a circuit different from the one that supplies power to the receiver.

– Consult the dealer or an experienced radio/TV technician.

WARNING! Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority

to operate the equipment.

This device complies with FCC Rules Part 15 and with Industry Canada licence-exempt RSS standard(s). Operation is subject to two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference that may be received or that may cause

undesired operation.

Le present appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisee

aux deux conditions suivantes :(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage

radioelectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement.

W.E.E.E. Product Recycling Declaration

For information regarding the recycling of this product you must contact the company from which you orignially purchased it. If you are discarding this product and not

returning it for repair then you must ensure that it is returned as identified by your supplier. This product is not to be thrown away with everyday waste.

Directive 2002/96/EC Waste Electrical and Electronic Equipment.

APPENDIX:

APPENDIX:APPENDIX:

APPENDIX:

SPECIFICATIONS

SPECIFICATIONSSPECIFICATIONS

SPECIFICATIONS

OPTICAL

Black Mirror Max. Coverage

Up to

12 m (40 ft) / 90°

Detector Technology

8 independent quad PIR detectors operating in true Quad configuration

Figure 6. Coverage Pattern

A. Top view

B. Side view of each detector

C. Image coverage range

Pet Immunity

Up to 18 Kg (40 lb)

ELECTRICAL

Input Power

Two 3V

2400 mAh,

17450

Lithium batteries

manufactured by EVE.

Battery Life (for typical use)

years

Note:

Minimum one year, typical 3 years (not verified by UL/ULC)

Low

Battery Threshold

4.0 V

Optional Mains Supply

Additional to batteries, 7.5 V

DC, 1.5 A

Note: For UL/ULC installation, the 7.5 VDC power connection was not evaluated by UL.

8 D-304493 TOWER CAM PG2 Installation Instructions

FUNCTIONAL

IR Illumination

10 m (33 ft)

Picture Resolution

320x240 pixels QVGA

160X120 pixels QQVGA

Frame Rate

fps

WIRELESS

Frequency Band (MHz)

Europe and

rest of world:

433

434, 868

869

USA:

912

919

Note: Only devices operating in band 912-919 MHz are UL/ULC listed.

Communication Protocol

PowerG

Tamper Alert

Reported when a tamper event occurs and in any subsequent message, until the tamper switch is

restored

MOUNTING

Mounting Type

Wall mounting

Mounting Height

1.5 – 3.0 m (5 – 10 ft).

Horizontal Adjustment

-45°to +45°, in 5°steps

Vertical Adjustment

0°to -10°, in 2.5°steps

ENVIRONMENTAL

Operating Temperatures

C to 60

C (

F to 140

Note:

For UL/ULC installation, evaluated to 66°C

Storage Temperatures

C to 60

C (

F to 140

Humidity

95% max.

White Light Immunity

Above 25000 lux

PHYSICAL

Size (H x L x W)

x 147 x 124 mm (6

/16 x 5

13/16 x

7/8”)

Weight (with battery)

00 g (

oz).

Color

White

PATENTS

U.S. Patents 7250605



6818881



5693943 (other patents pending)

WARRANTY

Visonic Limited (the “Manufacturer") warrants this product only (the "Product") to the original purchaser only

(the “Purchaser”) against defective workmanship and materials under normal use of the Product for a

period of twelve (12) months from the date of shipment by the Manufacturer.

This Warranty is absolutely conditional upon the Product having been properly installed, maintained and

operated under conditions of normal use in accordance with the Manufacturers recommended installation

and operation instructions. Products which have become defective for any other reason, according to the

Manufacturers discretion, such as improper installation, failure to follow recommended installation and

operational instructions, neglect, willful damage, misuse or vandalism, accidental damage, alteration or

tampering, or repair by anyone other than the manufacturer, are not covered by this Warranty.

The Manufacturer does not represent that this Product may not be compromised and/or circumvented or

that the Product will prevent any death and/or personal injury and/or damage to property resulting from

burglary, robbery, fire or otherwise, or that the Product will in all cases provide adequate warning or

protection. The Product, properly installed and maintained, only reduces the risk of such events without

warning and it is not a guarantee or insurance that such events will not occur.

THIS WARRANTY IS EXCLUSIVE AND EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES,

OBLIGATIONS OR LIABILITIES, WHETHER WRITTEN, ORAL, EXPRESS OR IMPLIED, INCLUDING

ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, OR

OTHERWISE. IN NO CASE SHALL THE MANUFACTURER BE LIABLE TO ANYONE FOR ANY

CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS WARRANTY OR ANY OTHER

WARRANTIES WHATSOEVER, AS AFORESAID.

THE MANUFACTURER SHALL IN NO EVENT BE LIABLE FOR ANY SPECIAL, INDIRECT, INCIDENTAL,

CONSEQUENTIAL OR PUNITIVE DAMAGES OR FOR LOSS, DAMAGE, OR EXPENSE, INCLUDING

LOSS OF USE, PROFITS, REVENUE, OR GOODWILL, DIRECTLY OR INDIRECTLY ARISING FROM

PURCHASER’S USE OR INABILITY TO USE THE PRODUCT, OR FOR LOSS OR DESTRUCTION OF

OTHER PROPERTY OR FROM ANY OTHER CAUSE, EVEN IF MANUFACTURER HAS BEEN ADVISED

OF THE POSSIBILITY OF SUCH DAMAGE.

THE MANUFACTURER SHALL HAVE NO LIABILITY FOR ANY DEATH, PERSONAL AND/OR BODILY

INJURY AND/OR DAMAGE TO PROPERTY OR OTHER LOSS WHETHER DIRECT, INDIRECT,

INCIDENTAL, CONSEQUENTIAL OR OTHERWISE, BASED ON A CLAIM THAT THE PRODUCT FAILED

TO FUNCTION.

However, if the Manufacturer is held liable, whether directly or indirectly, for any loss or damage arising

under this limited warranty, THE MANUFACTURER'S MAXIMUM LIABILITY (IF ANY) SHALL NOT IN

ANY CASE EXCEED THE PURCHASE PRICE OF THE PRODUCT, which shall be fixed as liquidated

damages and not as a penalty, and shall be the complete and exclusive remedy against the Manufacturer.

When accepting the delivery of the Product, the Purchaser agrees to the said conditions of sale and

warranty and he recognizes having been informed of.

Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, so these

limitations may not apply under certain circumstances.

The Manufacturer shall be under no liability whatsoever arising out of the corruption and/or malfunctioning

of any telecommunication or electronic equipment or any programs.

The Manufacturers obligations under this Warranty are limited solely to repair and/or replace at the

Manufacturer’s discretion any Product or part thereof that may prove defective. Any repair and/or

replacement shall not extend the original Warranty period. The Manufacturer shall not be responsible for

dismantling and/or reinstallation costs. To exercise this Warranty the Product must be returned to the

Manufacturer freight pre-paid and insured. All freight and insurance costs are the responsibility of the

Purchaser and are not included in this Warranty.

This warranty shall not be modified, varied or extended, and the Manufacturer does not authorize any

person to act on its behalf in the modification, variation or extension of this warranty. This warranty shall

apply to the Product only. All products, accessories or attachments of others used in conjunction with the

Product, including batteries, shall be covered solely by their own warranty, if any. The Manufacturer shall

not be liable for any damage or loss whatsoever, whether directly, indirectly, incidentally, consequentially or

otherwise, caused by the malfunction of the Product due to products, accessories, or attachments of

others, including batteries, used in conjunction with the Products. This Warranty is exclusive to the original

Purchaser and is not assignable.

This Warranty is in addition to and does not affect your legal rights. Any provision in this warranty which is

contrary to the Law in the state or country were the Product is supplied shall not apply.

Warning: The user must follow the Manufacturer’s installation and operational instructions including testing

the Product and its whole system at least once a week and to take all necessary precautions for his/her

safety and the protection of his/her property.

1/08

EMAIL: info@visonic.com

INTERNET: www.visonic.com

VISONIC LTD. 2015 TOWER CAM PG2 D-304493 (Rev. 3, 1/15)

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Visonic Sicherheitskamera Handbücher

Visonic

Visonic NC543W Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung