Vista VK2-108VRDIR37e Bedienungsanleitung

Please read this manual thoroughly before use, and keep it handy for future reference.

Quick Installation Guide

VK2-1080VRDIR37e Quick Guide V1.0

Quick Installation Guide

VK2-1080VRDIR37e Quick Guide V1.0

1. Description

This manual applies to the VK2-1080VRDIR37e full HD Vandal resistant varifocal dome with IR

illumination.

• Installation Steps

Follow these steps to install the VK2-1080VRDIR37e on your local network (LAN):

1. Check the package contents against the list below.

2. Connect the VK2-1080VRDIR35V16e

3. Set an IP address.

4. Set the password.

• Package Component

The system comes with the following components:

Camera Unit Installation CD Installation Guide Accessory Kit Template sheet

Notes:

1. Check your package to make sure that you received the complete system, including all

components shown above.

2. Adapter for DC 12V is not supplied.

• Contents in the installation CD

1. The User’s Manual

2. The SmartManager User’s Manual

3. The VK2-Client User’s Manual

4. The SmartManager Installation software

5. The VK2-Client Installation software

Quick Installation Guide

VK2-1080VRDIR37e Quick Guide V1.0

• Connection Cable

Camera Dimension

See the diagrams below for the exact dimension

Name

Description

Lens

Allows wide area to be monitored

Power Cable

Cable for Power source (DC 12V)

Ethernet Cable

Cable for Ethernet (POE)

Quick Installation Guide

VK2-1080VRDIR37e Quick Guide V1.0

2. Installation

2.1 Connection

• Camera Installation

Carefully remove the contents from the box, and verity that nothing was damaged in shipment.

1) Mark the screw hole positions on the ceiling or wall surface using the Template Sheet.

2) Disassemble the camera by removing the dome cover.

3) Mount the camera assembly using the Anchors (x2) and Screws (x2) to the surface of the

ceiling or wall

4) Reassemble the dome cover on the camera assembly. Turn Camera Cover clockwise to complete

installation

• Connecting to the RJ-45

Connect a standard RJ-45 cable to the network port of the network camera. Generally a

cross-over cable is used for directly connection to PC, while a direct cable is used for connection

to a hub or switch.

Micro SD memory slot

Insert the SD memory card.

• Connecting the Power

Connect the DC 12V power adaptor to the camera.

(This connection is not used if using PoE power)

Quick Installation Guide

VK2-1080VRDIR37e Quick Guide V1.0

2.2 Network Connection and IP assignment

The Camera supports the operation through the network. When a camera is first connected to the

network it has no assigned IP address. So, it is necessary to allocate an IP address to the device with

the “Smart Manager” utility found on the supplied CD. The factory default IP is “192.168.30.220”.

1. Connect the Camera / device to the network and power up.

2. Start SmartManager utility (Start>All programs>SmartManager>SmartManager), the main

window will be displayed, after a short while any network devices connected to the network will

be displayed in the list.

3. Select the camera on the list and click right button of the mouse. You can see the pop-up menu

below.

4. Select Assign IP. will see the "Assign IP Address" window. Enter the required IP address.

Note: For more information, refer to the Smart Manger User’s Manual.

Quick Installation Guide

VK2-1080VRDIR37e Quick Guide V1.0

3. Operation

The Camera can be used with Windows operating system and browsers. The recommended browsers

are Internet Explorer, Safari, Firefox, Opera and Google Chrome with Windows.

3.1 Access from a browser

1. Start a browser. (Internet Explorer) will be used in this example.

2. Enter the IP address or host name of the Camera in the Location/Address field of your browser.

3. You can see a starting page. Click Live View or Setup to enter web page.

4. The network camera’s Live View page appears in your browser.

3.2. Access from the internet

Access from the internet once connected, the Camera is accessible on your local network (LAN). To

access the Camera from the Internet you must configure your broadband router to allow incoming

data traffic to the network camera. To do this, enable the NAT-traversal feature, which will attempt to

automatically configure the router to allow access to the network camera. This is enabled from Setup

> System > Network > NAT.

For more information, please see “3.5.5 System>Network>NAT” of User’s Manual.

Quick Installation Guide

VK2-1080VRDIR37e Quick Guide V1.0

3.3 Setting the admin password over a secure connection

To gain access to the product, the password for

the default administrator user must be set. This

is done in the “Admin Password” dialog, which is

displayed when the Camera is accessed for the

setup at the first time. Enter your admin name

and password, set by the administrator.

Note: The default administrator username and

password is “admin”. If the password is lost, the

Camera must be reset to the factory default

settings. See “3.6 Resetting to the Factory

Default Settings”.

3.4 Live View Page

The live view page comes in several screen

modes:1920x1080, 1280x1024, 1280x720,

704x480(576),640x480,352x240(288) and

320x240. Users are allowed to select the

most suitable one out of those modes.

Please, adjust the mode in accordance with

your PC specifications and monitoring

purposes.

1) General controls

Live View Page Search & Playback Page Setup Page Help Page

The video drop-down list allows you to select a customized or pre-programmed

video stream on the live view page. Stream profiles are configured under Setup > Basic

Configuration > Video & Image. For more information, please see “3.5.1 Basic Configuration >

Video & Image” of User’s Manual.

The resolution drop-down list allows you to select the most suitable one

out of video resolutions to be displayed on live view page.

The protocol drop-down list allows you to select which combination of

protocols and methods to use depending on your viewing requirements, and on the properties of

your network.

Quick Installation Guide

VK2-1080VRDIR37e Quick Guide V1.0

2) Control toolbar

The live viewer toolbar is available in the web browser page only. It displays the following

buttons:

The Stop button stops the video stream being played. Pressing the key again toggles the

start and stop. The Start button connects to the Camera or start playing a video

stream.

The Pause button pause the video stream being played.

The Snapshot button takes a snapshot of the current image. The location where the

image is saved can be specified.

The digital zoom activates a zoom-in or zoom-out function for video image on the live

screen.

The Full Screen button causes the video image to fill the entire screen area. No other

windows will be visible. Press the 'Esc' button on the computer keyboard to cancel full

screen view.

The Manual Trigger button activates a pop-up window to manually start or stop the event.

3) Video Streams

The Camera provides several images and video stream formats. Your requirements and the

properties of your network will determine the type you use.

The Live View page in the Camera provides access to H.264, MPEG-4 and Motion JPEG video

streams, and to the list of available video streams. Other applications and clients can also access

these video streams/images directly, without going via the Live View page.

3.5 Camera Setup

This section describes how to configure the network camera, and is intended for product

Administrators, who have unrestricted access to all the Setup tools; and Operators, who have access

to the settings for Basic, Live View, Video & Image, Event, and System Configuration.

You can configure the Camera by clicking Setup in the top right-hand corner of the Live View page.

Click on this page to access the online help that explains the setup tools

When accessing the Camera for the first time, the “Admin

Password” dialog appears. Enter your admin name and

password, set by the administrator.

Note: If the password is lost, the Camera must be reset

to the factory default settings.

See “3.6 Resetting to the Factory Default Settings”.

Quick Installation Guide

VK2-1080VRDIR37e Quick Guide V1.0

3.6 Resetting to the factory default settings

To reset the Camera to the original factory settings, go to the Setup>System> Maintenance web page

(described in User’s Manual, “3.5.5 System > Maintenance”) or use the Reset button on the network

camera, as described below

• Using the Reset Button

Follow the instructions below to reset the Camera to the factory default settings using the Reset

button.

1. Switch off the Camera by disconnecting the power adapter.

2. Press and hold the Reset button with a straightened paperclip while reconnecting the power.

3. Keep the Reset button pressed for at least 2 or more seconds.

4. Release the Reset button.

5. The Camera resets to factory defaults and restarts after completing the factory

reset.

Caution: When performing a Factory Reset, you will lose any settings you have saved.

(Default IP 192.168.30.220)

3.7 More Information

For more information, please see the Camera User’s Manual, which is available on the CD included in

this package.

Reset Button

Andere Handbücher für VK2-108VRDIR37e

Inhaltsverzeichnis

Andere Vista Sicherheitskamera Handbücher

Vista

Vista VBC400-600 Bedienungsanleitung

Vista

Vista VBC502-960H Bedienungsanleitung

Vista

Vista VFD13C/HR Bedienungsanleitung

Vista

Vista VFD4V9Me Bedienungsanleitung

Vista

Vista Onvif VK2-1080XPTZ Bedienungsanleitung

Vista

Vista VK2-12MP360EXTIR Bedienungsanleitung

Vista

Vista VLI-4BL28V12IRQ Bedienungsanleitung

Vista

Vista VP-HDA30-PM Bedienungsanleitung

Vista

Vista Onvif VIP2 VK2-720VZMX Bedienungsanleitung

Vista

Vista VVRD28V12CM960H / U Bedienungsanleitung

Vista

Vista VVRDE 700 Bedienungsanleitung

Vista

Vista VVRD28V12MHDAW Bedienungsanleitung

Vista

Vista ONVIF VK2-1080XPTZF Bedienungsanleitung

Vista

Vista VSBCMC6LED Bedienungsanleitung

Vista

Vista VK2-1080BIR37e Bedienungsanleitung

Vista

Vista VC200 Series Bedienungsanleitung

Vista

Vista VK2-108VRDIR35V16e Bedienungsanleitung

Vista

Vista VK2-1080XIRPTZF Bedienungsanleitung

Vista

Vista powerdome pro series Bedienungsanleitung

Vista

Vista VK2-5MPBIR36V10Re Bedienungsanleitung

Vista

Vista VFD28V12CM960H Bedienungsanleitung

Vista

Vista Onvif VK2-1080XPTZ Bedienungsanleitung

Vista

Vista VIP Series Bedienungsanleitung

Vista

Vista VBC28V12MHDA Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung