Vitek TRANSCENDENT VTC-TNB48R4M2 Bedienungsanleitung
VITEK
VITEK
VTC-TNB48R4M2
VTC-TNB48R5V2
5.0 Megapixel Indoor/Outdoor
WDR IP IR Bullet Cameras
QUICK START GUIDE
FEATURES
• Megapixel Progressive Scan CMOS image sensor
• Advanced Starlight Technology Offers Dramatically Higher
Sensitivity to Light Producing Color Images in Very Dark & Night
Scenes
• Up to 30fps live view
• 3.6~10mm Varifocal Lens (VTC-TNB48R5V2) / Motorized 3.3-
12mm Motorized Varifocal Lens (VTC-TNB48R4M2)
• 48 Infrared LED’s with 160’ IR Range
• Digital Wide Dynamic Range (D-WDR)
• True Mechanical Day/Night function by ICR
• XD-DNR (2D-DNR & 3D-DNR) Noise Reduction
• On Board Motion Detection
• H.265/H.264/MJPEG Triple Streaming
• Secondary Video Output (CVBS)
• MicroSD memory card slot for Local recording supporting up to
128GB MicroSDXC cards
• Remote Viewing via CMS, Internet Explorer, and iOS & Android
Apps
• Minimal Latency with up to 10 simultaneous user connections
• ONVIF Compliant
• IP66 Weather Resistance
• Optional Junction Box Mount Available (VT-TJB01)
• 12VDC & PoE (Power over Ethernet) Operation
PLEASE NOTE:
Complete User Guide, Software, Tools, and Updates are
available online. Scan the QR Code or visit:
http://www.vitekcctv.com/Downloads
2 3
Components and Accessories
Overview
8
9
10
11
12
2
3
4
5
6
1
7
Camera
Quick Guide
Screws
Hex Wrench
Drill Template
Rubber Plug
Waterproof Cap
Service Port Cable
*VTC-TNB48R5V2 Only
1
2
3
4
5
6
7
8
9
10
11
12
RJ-45 Ethernet
Audio In
Audio Out
CVBS Output
Alarm I/O
RS-485
Power Cable
Zoom*
Focus*
Reset
Service Port
MicroSD Card Slot
3
Cable Connections
Weather Resistant Network Coupler
First connect the Waterproof Cap to an Ethernet patch cable, then
connect the cameras ethernet adaptor. If not powering the camera with
PoE, also connect the power Cable to an approved 12VDC Power
Supply.
1. Loosen the nut from the Weather Resistant Network Coupler,
2. Run ethernet cable through coupler, then attach a RJ-45 connector.
3. Tighten the nut and coupler for a weather resistant seal.
Network Cable
Optional 12VDC
Power Connection.
Not needed with PoE
ALM: COM
ALM: NO
ALM: IN
ALM: GND
RS-485 +
RS-485 -
4 5
Installation
Before beginning installation, make sure that the wall or ceiling is
strong enough to withstand 3 times the weight of the camera. The
mounting steps are as follows:
1. Attach the drill template to
the place where you want to
install the camera, then drill
4 screw holes and 1 cable
hole (if you want to route the
cables through the mounting
base) according to the drill
template
2. Route the cables and connect the power & video cables, use the
rubber plug to fill the gap of the mounting base. then secure the
mounting base to the ceiling or wall with screws.
Rubber Plug
Mount Base
5
Installation
3. Loosen the mount lock to adjust the Pan and Tilt of the camera, then
tighten the mount lock to secure the viewing angle adjustments.
4. To adjust the lens, start by removing the Lens Cover, then adjust
the Focus and Zoom levers to achieve a clear image. Replace
the Lens Cover. *VTC-TNB48R5V2 Only
5. Carefully remove the protective film from the lens to complete the
installation.
90° Tilt
360° Pan
Zoom
Focus
Lens Cover
6 7
LAN Configuration
The camera can be accessed on the local network either using the
IP-Tool or directly in a web browser.
1. Attach the drill template to the place where you want to install the
camera, then drill 3 screw holes and 1 cable hole (if you want to
route the cables through the mounting base) according to the drill
template
Accessing the Camera Using the IP-Tool
1. Make sure the camera and PC are connected to the LAN.
2. Locate the IP-Tool installer on the included Product Documentation
CD, then install on the PC. Open the installed application.
3. Modify the IP address. The default IP address is 192.168.226.201.
Click the information of the camera listed in the above table to show
the network information on the right side. Modify the IP address and
gateway of the camera and make sure its network address is in the
same local network segment as the computer’s. Please modify the
IP address of your device according to the practical situation.
For example, the IP address of your computer
is 192.168.13.4. So the IP address of the
camera shall be changed to 192.168.13.X.
After modification, please input the password
of the administrator and click “Modify” button
to modify the setting.
** Default admin password: “123456".
7
4. Double-click the IP address and then the system will pop up the web
browser to connect IP-CAM . IE browser will download the Active X
control automatically. After downloading, a login window will pop up
as shown below:
Input the user name and password to log in.
Default user name: admin / Default password: 123456.
Directly Access Through a Web Browser
The default network settings are as shown below:
IP address: 192.168.226.201 HTTP: 80
Subnet Mask: 255.255.255.0 Data Port: 9008
Gateway: 192.168.226.1
You may use the above default settings when you log in the camera for
the first time.
1. Manually set the IP address of the PC and the network segment
should be as the same as the default settings of IP-CAM. Open the
network and share center. Click “Local Area Connection” to pop up
the following window.
Select “Properties” and then select Internet protocol according to the
actual situation (for example: IPV4). Next, click “Properties” button to
set the network of the PC.
8
2. Open the IE Browser and input the default address of IP-CAM and
confirm. The IE browser will download Active X control automatical-
ly.
3. After downloading Active X control, the login dialog box will pop up.
4. Input the default username and password and then enter to view.
WAN Configuration
Access the camera by the router or virtual server for example.
1. Make sure the camera is connected to the LAN; Then log into the
camera via LAN and go to System Congfig→Network Config→Port
menu to set up the port number.
2. Enter System Config→Network Config→IP Address menu to modify
the IP address.
4. Open the web browser and input its WAN IP and HTTP port to
access the IP-CAM.
3. Go to the router’s management interface through IE browser to
forward the IP address and port of IP-CAM in the “Virtual Server”.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Vitek Sicherheitskamera Handbücher
Vitek
Vitek Transcendent VTC-TNT3RFE Bedienungsanleitung
Vitek
Vitek VTC-IRE70 Bedienungsanleitung
Vitek
Vitek VTC-TNT4RFS Bedienungsanleitung
Vitek
Vitek VTC-IRM40-2812 Bedienungsanleitung
Vitek
Vitek VTD-TND8RMA4 Bedienungsanleitung
Vitek
Vitek TRANSCENDENT VTD-T4D6HR8MD Bedienungsanleitung
Vitek
Vitek Transcendent Series Bedienungsanleitung
Vitek
Vitek VTD-TTD30R2V Bedienungsanleitung
Vitek
Vitek VTD-TND4RMS Bedienungsanleitung
Vitek
Vitek VT-PIRC2H Bedienungsanleitung
Vitek
Vitek VTC-TTAT2HR2F Bedienungsanleitung
Vitek
Vitek Transcendent VTD-TND4RMA3B Bedienungsanleitung
Vitek
Vitek Mighty VTD-MVP2810/L35 Bedienungsanleitung
Vitek
Vitek VTC-TNT5RFEB-2 Bedienungsanleitung
Vitek
Vitek Transcendent VT-TPTZ25HRAN-4PNL Bedienungsanleitung
Vitek
Vitek VTD-T4D6HR2MD Bedienungsanleitung
Vitek
Vitek Transcendent VTC-TNB4RFAD-2 Bedienungsanleitung
Vitek
Vitek VTC-C750WDR Bedienungsanleitung
Vitek
Vitek OnCue VT-PTZ230HD Bedienungsanleitung
Vitek
Vitek VTC-B301 Bedienungsanleitung
