Vitek VTD-TND5RMEA Bedienungsanleitung

VITEK

QUICK START GUIDE

VTD-TND5RMEA

Transcendent Series 5 MegaPixel

Motorized IP WDR

Vandal Dome Camera

FEATURES:

• 1/2.7” 5.0 Megapixel CMOS Image Sensor

• Up to 20fps@5MP (2880 × 1620), Up to 30fps@4MP (2560 × 1440), 3MP

(2304 × 1296), 1080P (1920 × 1080), 720P (1280 × 720), D1, 480× 240, CIF

• 2.8~12mm Motorized Varifocal Lens

• Matrix IR (up to 165’ IR Range)

• True Wide Dynamic Range (120dB)

• True Mechanical Day/Night function by ICR

• XD-DNR (3D & 2D-DNR) Noise Reduction

• Region Intrusion Detection, Object Abandoned / Missing, Scene Change Detection, Line

Crossing, Video Blur, Video Color Cast Detection

• H.265+ / H.265 / H.264+ / H.264 / MJPEG

• MicroSD Card Slot for Local Recording (Up to 256GB)

• 1 Ch. Audio In + Built-in Mic*

• Remote Viewing via CMS, IE (plug-in required)/Google Chrome/Edge/Firefox/Safari,

and iOS & Android Apps

• ONVIF Compliant

• IP67 Weather Resistance

• Optional Junction Box (VT-TJB010), Wall Mount (VT-TWMT-A2 [reqs. VT-TJB010]),

Pendant Mount (VT-TPDMT-A2 [reqs. VT-TJB010]), and In-Ceiling Semi Flush Mount

(VT-TFMT-L2) Available See Additional Mounting Options on Pg. 9

• 12VDC & PoE (Power over Ethernet) Operation

• 3-Year Warranty

*Please research local, state and federal lawsregarding the implementation

of audio surveillance.

PLEASE NOTE:

Complete User Guide, Software, Tools, and Updates are

available online. Scan the QR Code or visit:

http://www.vitekcctv.com/Downloads

2 3

Components and Accessories

Overview

Connect the Weather Resistant Cap to an Ethernet patch cable.

Connect the cameras ethernet adaptor. If not powering the camera

with PoE, also connect the power Cable to an approved 12VDC

Power supply.

Weather Resistant Cap

1. Ethernet Connector

2. Audio Input (3.5mm)

3. Power Connector

4. MicroSD Card Slot

5. Reset

6. Microphone

Camera Quick Start Guide 4 Tapping Screws Rubber Plug

Allen Key Drill Template 4 Plastic Plugs

Installation

Before beginning installation, make sure that the wall or ceiling is strong enough

to withstand 3 times the weight of the camera. Install in dry conditions. Do not

leave the lower dome off the camera for more than three hours during

installation. Remove the protective film only when the installation is complete.

1) Rotate the trim-ring counter-clockwise to remove it from the camera, then loosen the

screws to remove the lower dome.

2) Attach the drill template to where you will install the cameras, then drill 4 screw

holes and one cable hole if routing the cables through (according ot the template)

**Route and connect the cables

according to the instructions below

3.55”

.18”

1. Loosen the nut from the Weather-

Resistant Network Coupler.

2. Run ethernet cable through

the coupler, then attach a RJ-45

connector.

3. Tighten the nut and coupler

for a weather resistant seal.

1. 2.

4 5

3) Secure the camera to the wall or ceiling with the provided screws

5) Prior to the Three-Axis adjustment, preview the camera on a monitor and adjust

as necessary to achieve the optimal viewing angle.

5) Install the lower dome back onto the

camera using the provided screws.

Replace the trim ring and turn it

clock-wise until it locks. Finally, gently

remove the protective film.

INSTALLATION WITH A JUNCTION BOX

First, secure the junction box to the wall or ceiling with screws, then rotate the trim ring

counter-clockwise to remove it from the camera and loosen the screws to open lower dome.

Then, route and connect the cables, and fasten the camera to the J-box with screws. Finally, Adjust

the viewing angle and re-install the lower dome and trim ring back onto the camera.

LAN Configuration

The camera can be accessed on the local network either using the

IP-Tool or directly in a web browser.

Accessing the Camera Using the IP-Tool

1. Make sure the camera and PC are connected to the LAN.

2. Locate the IP-Tool installer at www.

vitekcctv.com/Downloads/Soft-

ware/Transcendent-IPTool_v2.0.2.zip

, then install on the PC. Open

the installed application.

3. Modify the IP address. The default IP address is 192.168.226.201.

Click the information of the camera listed in the above table to show

the network information on the right side. Modify the IP address and

gateway of the camera and make sure its network address is in the

same local network segment as the computer’s. Please modify the

IP address of your device according to the practical situation.

For example, the IP address of your computer

is 192.168.13.4. So the IP address of the

camera shall be changed to 192.168.13.X.

After modification, please input the password

of the administrator and click “Modify” button

to modify the setting.

** Default admin password: “123456".

IP Camera

Swi tch

Rout er Comput er

Network Cable Network Cable

6 7

4. Double-click the IP address and then the system will pop up the web

browser to connect IP-CAM . IE browser will download the Active X

control. After downloading, a login window will pop up as shown

below:

Input the user name and password to log in.

Default user name: admin / Default password: 123456.

Directly Access Through a Web Browser

The default network settings are as shown below:

IP address: 192.168.226.201 HTTP: 80

Subnet Mask: 255.255.255.0 Data Port: 9008

Gateway: 192.168.226.1

You may use the above default settings when you log in the camera for

the first time.

1. Manually set the IP address of the PC. The network segment should

be the same as the default settings of IP-CAM. Open the network

and share center. Click “Local Area Connection” to pop up the

following window.

Select “Properties” and then select Internet protocol according to the

actual situation (for example: IPV4). Next, click “Properties” button to

set the network of the PC.

2. Open the IE Browser and input the default address of IP-CAM and

confirm. The IE browser will download Active X control.

3. After downloading Active X control, the login dialog box will pop up.

4. Input the default username and password and then enter to view.

WAN Configuration

Access the camera by the router or virtual server for example.

1. Make sure the camera is connected to the LAN; Then log into the

camera via LAN and go to System Congfig→Network Config→Port

menu to set up the port number.

2. Enter System Config→Network Config→IP Address menu to modify

the IP address.

4. Open the web browser and input its WAN IP and HTTP port to

access the IP-CAM.

3. Go to the router’s management interface through IE browser to

forward the IP address and port of IP-CAM in the “Virtual Server”.

5. For additional setup, features and functions, please scan the

QR code on the front page of this quick guide and download

the complete manual.

8 9

Image Sensor

Image Size

Resolution

Min. Illumination

Electronic Shutter

Lens

IR LEDs (Range)

Video Compression

Audio Compression

Main-Stream

Sub, Third Stream

Bit Rate / Type

Wide Dynamic Range

Digital Noise Reduction

Other Features

Image Setting

Analytics

Smart Alarm

General Functions

Region of Interest (ROI)

Hardware Reset

Analog Video Output

Audio

Local Storage

Remote Viewing

Supported Browsers

Connection Protocol

Weather Resistance / Impact Rating

Power Input

Power Consump 12VDC, PoE

Working Environment

Weight Net (Shipping), Dimensions (Dia×H)

1/2.7” 5.0 Megapixel CMOS Image Sensor

5 MegaPixel (2880 × 1620)

Up to 20fps@5MP (2880 × 1620), Up to 30fps@4MP (2560 × 1440), 3MP (2304 × 1296), 1080P (1920 × 1080), 720P (1280 × 720), D1, 480× 240, CIF

0.007 lux @F1.6, AGC ON; 0 lux with IR

1 s ~ 1 / 100000 s

2.8~12mm Motorized Varifocal @F1.4, FoV H: 100°~36.5°, FoV V: 52°~20.5°, FoV Diag: 116 °~41°

3 Matrix Style IRs (up to 165’)

H.265+ / H. 265 / H.264+ / H.264 / MJPEG

G.711A / G.711U

5MP(1~20fps)/4MP/3MP/1080P/720P(1~30fps)

720P/D1/ CIF (1~30fps), 60Hz: D1/480× 240/CIF (1~30fps)

64 Kbps ~ 8 Mbps / VBR + CBR

120dB WDR

3D-DNR

Back Light Compensation, Highlight Compensation

ROI, Saturation, Brightness, Hue, Contrast, Wide Dynamic, Sharpness, Image Mirror, Image Flip, NR

Region Intrusion, Abandoned Object, Scene Change, Line Crossing, Video Blur, Video Color Cast Detection

Motion Detection, SD Card Error, SD Card Full

Watermark, IP Filter, Video Mask, Illegal Login Lock

Each ROI to be configured separately

Yes

1 Ch. Audio In + Built-in Mic*

Built-in Micro SD card slot up to 256GB

CMS / Web Browswer / iOS & Android Apps

IE (plug-in required) / Google Chrome / Edge / Firefox / Safari

ONVIF

IP67 / IK10

12VDC / PoE

350mA (LEDs Off) / 800mA (LEDs On), <8.5W

-22° ~140° (-30°C ~ 60°C) / < 95% Humidity

32.10oz / 2.01lb / 910g (52.91oz / 3.31lb / 1460g), 5.55 × 3.94” (141 ×100mm)

VTD-TND5RMEA Detailed Specifications

*Please research local, state and federal laws regarding the implementation of audio

surveillance.

VT-TPLMT

Transcendent

Universal Pole Mount -

reqs. VT-TJB010 /

VT-TJB010 +

VT-TWMT-A2

VT-TCNMT

Transcendent Universal

Corner Mount -

reqs. VT-TJB010 /

VT-TJB010 +

VT-TWMT-A2

OPTIONAL ACCESSORIES

AND RELATED PRODUCTS

FOR VTD-TND5RMEA

VT-TJB010

Optional Junction

Box

VT-TPDMT-A2

Pendant Mount

- reqs. VT-TJB010

VT-TFMT-L2

Optional Semi

Flush Mount

VT-TWMT-A2

Wall Mount -

reqs. VT-TJB010

5.48”

7.68”

5.47”

5.54”

5.48”

7.84”

9.17”

8.46”

6.43”

8.46”

8.47”

10 11

OPTIONAL ACCESSORIES AND

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung