Vivotek AM-518 Bedienungsanleitung
IP Surveillance
User’s Manual
Using AM-518 mounting adapter
and compatible accessories
VIVOTEK Fixed Dome Series
Mounting kit
Rev. 1.1b
2
Compatible VIVOTEK Cameras
I
R4.0000
R2.5000
AM-518 Mounting Adapter Mechanical Drawing
Outdoor series FD8362, FD8362E, FD8361, FD8335H, FD7141, FD7141V,
FE8171V, FD8372
Indoor series FD8161, FD8162, FD8135H, FD7131, FD7132
AM-518 Mounting Adapter Package Contents
Revison History:
Rev. 1.1: Added Fisheye camera mounting details.
Rev. 1.1a: Updated the model names of compatible accessories.
Rev. 1.1b: Added supported models, FD8335H, FD8135H, and FD8372.
3
English
Compatible Accessories (1): AM-311 Pole Mount Bracket
Compatible Accessories (2): AM-411 Corner Mount Bracket
Compatible Accessories (3): AM-711 Junction Box
Compatible Accessories (4): AM-212 Wall Mount Bracket
Compatible Accessories
II
4
Compatible Accessories (5-1): AM-114 Pendant Head
Compatible Accessories (5-2): AM-115 Pendant Pipe
5
English
Mounting & Cabling
III
Above are the locations of different groups of mounting holes for matching different
cameras:
Hole Type Applicable Cameras
AFD8362E, FD8362, FD8361, FD8335H, FD7141, FD7141V, and
FD8372.
BFD8161, FD7131, FD7132
CFD8162, FD8135H
DFE8171V
Align the mounting holes on your mounting plate (outdoor series) or on the camera (indoor
series) to match those on the mounting adapter.
For cabling and conguration details with each camera, please refer to their
documentation. Refer to the table below for the screws to be used with each type of
mounting holes:
Screw Description Quantity Applies to
M5X10 Phillips pan head 4 A
M4X20 Phillips pan head 2 B
M4X12 Phillips pan head 3 C
M3X10 Phillips pan head 3 D / D+
Mounting Hole Denitions
6
Hole marked as D+
Due to its unique mechanical design, the mounting procedure for an FE8171V sheye
camera is specically described as follows:
1. Remove the camera's top cover.
2. Fasten 2 included screws to the D holes (not the D+ hole).
3. Align the camera with the mounting adapter and let the 2 screws enter the key holes
located on the side where the camera's cabling interfaces reside, e.g., the Ethernet port.
4. Rotate the camera counter-clockwise. You can then see the D+ hole through the slotted
screw hole (in front of the Micro SD slot).
5. Fasten screws to secure the camera with the mounting adapter.
NOTE:
7
English
Below is a general, sample procedure using a Wall mount bracket:
1. Locate the position where you want to install the wall mount bracket and camera. Drill
holes on the wall for securing the bracket and for routing the cables.
Secure the bracket by hammering anchors into the wall and then fasten screws through
it.
2. Route power lines and other cables through the wall and the bracket.
3. Attach the mounting adapter to the bracket by rotating it clockwise until it is tightly
fastened.
1
2
3
4
55
6
4. Use the included hex wrench to secure the mounting adapter to the wall mount bracket.
5. For models using the A holes (please refer to the mounting hole diagram on the previous
page), secure its mounting plate to the mounting adapter above.
For the indoor models, mounting plates are not necessary.
6. For outdoor models - secure the camera to the mounting plate.
For indoor models -secure the camera directly to the mounting adapter.
When cabling is done, proceed with initial setup such as enabling network access, focus
tuning, or zooming. When done, secure the outer dome cover.
Cables
Wall mount
bracket
Mounting adapter
Mounting plate
Dome camera
IMPORTANT:
Wall Mount Installation
The screws and mounting surface must
be able to support a weight of 6 kg.
8
Below is a closer view on routing cables and matching a mounting plate.
Wall Mount Bracket
Mounting Adapter
Cables
FD8362E Mounting Plate
NOTE:
Use the correct type of screws when installing cameras to the mounting adapter. Refer to
page 5 for the screw type. The sample mounting positions for FD8362E (or FD8335H and
FD8372) are shown below.
A
A
A
A
9
English
307 mm
115 mm
178 mm
1
Below is a sample procedure using a Pendant pipe:
1. Determine a hard surface ceiling location, and use the four mounting holes on the
pendant head to mark the positions where holes will be drilled to secure the pendant
head.
Note that screws are user-supplied and they should be 11mm long at least.
Pendant Pipe Installation
Shown on the right is an exemplary illustration for
the FD8135H and FD1862 indoor cameras. Refer
to page 5 for the screw type.
10
2
4
5
3
7
6
8
2. Locate the position where you want to install the pendant pipe and camera. Drill holes
on the ceiling for securing the pendant head. Secure the pendant head by hammering
anchors into the ceiling and then fasten screws through it.
3. Route power lines and other cables through the side bushing and/or conduits (user-
supplied), and through the pendant pipe.
4. Secure pendant pipe to the pendant
head by rotating it clockwise
until it is tightly fastened.
Pendant Head
Pendant Pipe
Mounting Adapter
Mounting Plate
Cables
IMPORTANT:
The screws and mounting surface
must be able to support a weight of
6 kg.
Inhaltsverzeichnis
Andere Vivotek Rack & Stand Handbücher
Vivotek
Vivotek Fixed Dome AM-528 Bedienungsanleitung
Vivotek
Vivotek AM-21M Bedienungsanleitung
Vivotek
Vivotek AM-10F Bedienungsanleitung
Vivotek
Vivotek Bullet Series Bedienungsanleitung
Vivotek
Vivotek AM-412 Bedienungsanleitung
Vivotek
Vivotek AM-218 Bedienungsanleitung
Vivotek
Vivotek AM-412 Bedienungsanleitung
Vivotek
Vivotek AF101 Bedienungsanleitung
Vivotek
Vivotek Fixed Dome Series Bedienungsanleitung
Vivotek
Vivotek AM-412 Bedienungsanleitung
Beliebte Rack & Stand Handbücher anderer Marken
Salamander
Salamander Acadia AC/W/L400/WH Bedienungsanleitung
Fohhn
Fohhn VAT-09 Benutzerhandbuch
ricoo
ricoo FS0522 Bedienungsanleitung
AMSOIL
AMSOIL BMK-22 Kurzanleitung
Kargo Master
Kargo Master 48220 Bedienungsanleitung
Milestone AV Technologies
Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung
