Vivotek AM-214 Bedienungsanleitung
IP Surveillance
User’s Manual
VIVOTEK Fixed Dome & PTZ Series
Wall-mount Bracket
Using AM-214 wall-mount bracket
and compatible accessories
Rev. 1.1
2
Compatible VIVOTEK Cameras
I
AM-214 Wall-mount Bracket
Fixed Dome series FD8133, FD8134, FD8133V, FD8134V, FD8161, FD7132,
FD7131, FD8162, FD8135H, FD8362E, FD8362, FD8372,
FD8335H, FD8361, FD8361L, FD8131
PTZ series PZ7111, PZ7112, PZ7121, PZ7122, PZ7131, PZ7132,
PZ7151, PZ7152, PZ81x1W, PZ81x1
You may also refer to VIVOTEK's website for the list of supported models. Support for other models can
be available through time.
3
English
Accessories
II
Adaptor ring for FD8162
Installation
III
Above are the locations of different groups of mounting holes for matching different
cameras:
Hole Type Applicable Cameras Screw No. of
screws
AFD8161 / FD7132 / FD7131 M4X15 2
FD8162 / FD8135H 4
BFD8133V / FD8134V M4X8XD6 3
CFD8133 / FD8134 / FD8131 M3X6 2
DPZ7111 / PZ7112 / PZ7121 / PZ7122 / PZ7131 /
PZ7132 / PZ7151 / PZ7152 / PZ81x1W / PZ81x1 M3X4 2
E1 FD8335H / FD8361 / FD8361L / FD8362 / FD8362E /
FD8372
M4X15 4
E2 FD8361 (cables routed to the side of the bracket)
E3 FD8361 (cables routed to the side of the bracket)
For cabling and conguration details with each network camera, please refer to their
documentation.
Mounting Hole Denitions
4
Refer to the table below for the description of the included screws:
Screw Description Quantity Applies to
M4X15 Phillips pan head 4 A holes
M3X4 Phillips pan head
(black)
2 D holes for PZ
and PT series
M4X8XD6 Phillips pan
head
3 B holes
M4X25XD9 Phillips pan
head
4 Securing the
bracket to wall
M3x6 Phillips pan head 2 C holes
Plastic anchors 4 Securing the
bracket to wall
NOTE:
1. It is presumed that this wall-mount bracket is installed with a hole drilled on the wall for
routing power lines, DI/DO, and Ethernet cables.
2. Route cables before you secure the wall-mount bracket to a wall.
3. For details on the cable connections with each camera, please refer to their Quick
Installation Guide.
5
English
Below is a general, sample procedure using a wall mount bracket:
1. Locate the position where you want to install the wall mount bracket and camera. Drill
holes on the wall for securing the bracket and for routing the cables.
2. Secure the bracket by hammering anchors into the wall and then fasten screws through
the four mounting holes on the bracket.
3. Route power lines and other cables through the wall and the bracket.
4. Align the camera's mounting holes with the B holes. Secure the camera to the wall
mount bracket as shown below.
M4X8XD6 Screws
Aligned with B holes
Route cables through here
IMPORTANT!
Wall Mount Installation - FD8134V
The screws and mounting surface must be
able to support a weight of 4 kg.
6
5. Proceed with initial setup such as enabling network access, focus tuning, or zooming.
When done, secure the outer dome cover.
NOTE:
Use the correct type of screws when installing cameras to
the mounting cap. Refer to page 3 for the screw type.
7
English
M3X6 Screws
Below is a sample procedure using wall mount bracket and an FD8134:
1. Determine a hard surface wall location, and use the four mounting holes on the wall
mount bracket to mark the positions where holes will be drilled to secure the bracket.
Wall Mount Installation - FD8134
2. Drill holes on the wall for passing cables and for securing the wall mount bracket.
3. Secure the bracket by hammering anchors into the wall and then fasten screws.
4. Route power lines and other cables through the bracket and wall.
5. Secure camera to the wall mount bracket using the C holes and M3x6 screws.
6. Proceed with initial setup such as enabling network access, focus tuning, or zooming.
When done, secure the outer dome cover.
8
Below is a sample procedure using wall mount bracket and an FD8162:
1. Determine a hard surface wall location, and use the four mounting holes on the bracket
to mark the positions where holes will be drilled to secure the bracket.
Wall Mount Installation - FD8162
M4X15
A* holes
Camera Lens Orientation
2. Drill holes on the wall for securing the bracket and for routing cables.
3. Route cables through the wall and bracket.
4. Secure the wall mount bracket to the wall using the included screws and plastic
anchors.
5. Rotate the adaptor ring to match the camera lens orientation your prefer, e.g., to the
front or to the left. Secure the adaptor ring to bracket using the M4X15 screws to the A2
and A4 holes on the bracket.
9
English
6. Secure the camera to the adaptor ring using the included screws.
7. Connect power lines and cables to the camera.
8. Proceed with initial setup such as enabling network access, focus tuning, or zooming.
When done, secure the outer dome cover.
Below is a general, sample procedure for installing a PZ pr PT series camera with the wall
mount bracket:
1. Detach the mount panel by loosening 5 screws from the wall mount bracket.
Wall mount
bracket
Wall Mount Installation - PZ7151 (and Applies to All PZ Series)
10
2. Secure the camera from the inner side of the mount panel by driving M3 screws to the
bottom of camera.
3. Locate the position where you want to install the wall mount bracket. Drill holes on the
wall for securing the bracket and for routing cables.
4. Route power lines and other cables through the wall and the bracket.
5. Secure the wall mount bracket to the wall using the included fasteners and screws.
6. Attach the camera and the mount panel to the wall mount bracket using the 5 screws
you previously removed.
7. Connect power lines and cables, and you may now begin the initial connection and
conguration.
M3X4
NOTE:
Use the correct type of screws when installing cameras to
the mounting cap. Refer to page 3 for the screw type.
Inhaltsverzeichnis
Andere Vivotek Sicherheitskamera Handbücher
Vivotek
Vivotek PT3113 Bedienungsanleitung
Vivotek
Vivotek PZ6112 Bedienungsanleitung
Vivotek
Vivotek FE8173 Bedienungsanleitung
Vivotek
Vivotek TB5396A Bedienungsanleitung
Vivotek
Vivotek C Series Bedienungsanleitung
Vivotek
Vivotek Supreme FD8362 Bedienungsanleitung
Vivotek
Vivotek FD8156 Bedienungsanleitung
Vivotek
Vivotek IT9389 Series Bedienungsanleitung
Vivotek
Vivotek IP9165-LPC Bedienungsanleitung
Vivotek
Vivotek VORTEX FD837-HTV Bedienungsanleitung
Vivotek
Vivotek CC9381-HV Bedienungsanleitung
Vivotek
Vivotek PZ8111 Bedienungsanleitung
Vivotek
Vivotek PT7135 Bedienungsanleitung
Vivotek
Vivotek IP8352 Bedienungsanleitung
Vivotek
Vivotek SD9362-EH Bedienungsanleitung
Vivotek
Vivotek FD8366-V Bedienungsanleitung
Vivotek
Vivotek FD9182-H Bedienungsanleitung
Vivotek
Vivotek Supreme FD8363 Bedienungsanleitung
Vivotek
Vivotek 4712123678542 Bedienungsanleitung
Vivotek
Vivotek FE8171V Bedienungsanleitung
