Vivotek SD83X4E Bedienungsanleitung
EN-1
English
Warning Before Installation
Refer to your user’s manual for the
operating temperature.
Power off the Network Camera as soon as
smoke or unusual odors are detected.
Do not touch the Network Camera during
a lightning storm.
Do not disassemble the Network Camera.
Do not drop the Network Camera.
Do not insert sharp or tiny objects into the
Network Camera.
Do not manually pan and tilt the Network
Camera when the power is on.
Package Contents
1
5
1
0
0
0
0
2
1
0
G
Software CD / Warranty Card
Wall Mount Bracket / Screws
SD83x4E/83x6E
Screws / Alignment Sticker / T25
Stardriver / Desiccant Bags
Waterproof Connectors / Terminal Blocks /
Ethernet Cable / Ground Wire
Quick Installation Guide PC/ABS / Smoked Dome Cover / IO Cable
(Separately Purchased)
EN-2
Inner View
Board-to-board
Connector
Lens
Outer View
Physical Description
2
Ethernet 10/100
RJ45 Plug
General I/O
Terminal Block
SD/SDHC/SDXC Card Slot
Ethernet
DI GND
DI4
DI3
DI2
DI1
DO2
DO1
DO+(12V)
AC24V
AC24V
Reserved
MIC IN
RS485-
RS485+
Status LED
Network LED
Reset Button
Interface Section
Camera Body
This drawing shows a camera with its dome
cover removed.
The SD card slot is accessed
by removing the top section
using the T25 stardriver.
EN-3
English
Hardware Installation
3
RJ45 Cable Dimension (unit: mm)
Use CAT5e cables only.
3-1. Connecting RJ45 Ethernet Cable
12
3
45
6
78
(D) (B)
(C)
(A)
(E)
Components of the Waterproof
Connector
Screw Nut (C)
Housing (D)
Gasket (E)
Seal (B)
Sealing Nut (A)
100
Prepare an Ethernet cable
and strip part of the sheath.
Insert the housing into the
screw nut.
Insert the seal into the housing.
Insert the stripped Ethernet
cable through the sealing
nut and the housing.
Clamp the cable with
an RJ45 plug.
Push the RJ45 plug into the
housing, then secure the
sealing nut tightly.
Attach the gasket to the front
of the housing.
Assembling Steps
Recommended cable gauge: O.D.
5.5~7
Connect the Ethernet cable to the RJ45 cable and secure the
connectors tightly.
EN-4
3-2. Connecting Power and I/O Wires
If you need to connect I/O wires and 24V power, disassemble the top section of the
camera. It is highly recommended to complete the following before you can mount
the speed dome camera at the installation site:
Skip this section and move to Section 3-3 if you connect the Ethernet cable only.
1-3
1-2
1-1
Plan the wire length and complete cabling to
the Interface Section
Cabling through the dome cap and waterproof
connectors
Connect with the mount bracket
3-2-1. Cabling through the Waterproof Connectors
Components of the Waterproof Connector
Seals (C)
Housing (D)
Sealing Nut (E)
Seal (B)
Screw Nut (A) •
Wire range: 13~16AWG (1.2~1.8mm)
•
A socket wrench for the M20 hex nut is
required.
EN-5
English
1. Disassemble the components of the waterproof connector into parts (A) ~ (E) as
shown above.
2. Remove the plastic stopper from the bottom of the dome cap and keep the M20 hex
nut for later use.
3. Depending on the number of wires, remove seals (C) from the rubber seal (B).
4. If you have external devices such as sensors and alarms, feed IO wires through the
waterproof connector (E --> D --> B --> A) as illustrated below. Note that there are 16
holes on the seal (B), and wire range is beteen 1.2 and 1.8mm.
5. Push the seal (B) into the housing (D).
6. Secure the sealing nut (E) tightly.
(E)(D)(B)(A)
(C)
(B)
(D)
3-2-2. Connect cables:
Ethernet
DI GND
DI4
DI3
DI2
DI1
DO2
DO1
DO+(12V)
AC24V
AC24V
Reserved
MIC IN
Line OUT
Audio GND
RS485-
RS485+
AC24V DI GND
AC24V DI4
Reserved DI3
MIC IN DI2
Line OUT DI1
Audio GND DO2
RS485- DO1
RS485+ DO+(12V)
Wire range: 13~16AWG
Strip length: 6~7mm
Screw: M2
1. Use a small-size at-blade screwdriver to secure IO
wires to the included terminal blocks. You may aslo
purchase an IO combo cable from VIVOTEK.
M20 hex
nut
The max. output load on
DO pins is 50mA.
EN-6
2. Feed the Ethernet cable and IO wires through the mounting bracket, the openings on
the dome cap, and to the interface section. Attach the rubber seal plug to dome cap for
water proong.
Mount bracket
Dome cap
Interface Section
1. IO wires are user-supplied.
2. Avoid touching the circuit boards to prevent damage by electro static discharge.
NOTE:
3. Secure the included ground wire to the dome cap, pass it through the mount bracket,
and connect the other end to a grounded conduit later.
2
3
EN-7
English
1
2
3
Combine the components of the top section.
1. Press the seal ring into the groove on canister. Use the black machine screws (M4x8)
to attach the interface section to the dome cap. Note that you should orient and align
the spring contacts with the dehumidier unit on the dome cap.
2. Secure the dome cap to the mount bracket.
3. Use the included hex wrench to secure the connection.
When done, the top section will
look like this. You can now carry the
camera and the top section
to the installation site.
Mount
Bracket
Interface Section
Board-to-board
Connector
3-2-3. Connect with the Mount Bracket
Seal Ring
EN-8
HD WDR Pro
IMPORTANT:
You should examine whether the color of the
silica gel inside the chassis has turned red. If
so, you should replace the desiccant bag.
To replace the desiccant bags:
1. Remove the dome cover by loosening 4 T25
anti-tamper screws.
2. Replace the desiccant bags by attaching
them rmly to the inside of the chassis.
3. Re-install the dome cover.
Also note the following:
1. Do not install the camera in a raining day.
2. It takes approximately 2 days to suppress
the moisture level to 30% or lower.
3. Condensation may still be observed from on
the dome cover within 30 minutes.
EN-9
English
3-3. Mounting the Network Camera
NOTE:
Before mounting the camera, install an SD card if you prefer recording to local storage.
1
23
5
4
HD WDR Pro
1. The camera weighs 3.66kg. Select a rigid mounting location to prevent vibration to
the camera. Attach the alignment sticker to the wall.
2. Drill 4 pilot holes (10mm in diameter and 4cm deep) into the wall, and then hammer
in threaded anchors. Note that you should hammer the anchors with hex nuts on
them so that the threaded poles will not be deformed! If preferred, drill another hole
for routing cables.
3. Secure the wall mount bracket to wall using 4 sets of captive washers and nuts.
4. Align the camera with the wall mount bracket.
5. Tighten 3 included screws using a Phillips screwdriver. Make sure all parts have been
securely tightened.
3-3-1. Mounting with Ethernet Connection Only
Andere Handbücher für SD83X4E
5
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Vivotek Sicherheitskamera Handbücher
Vivotek
Vivotek 4712123678542 Bedienungsanleitung
Vivotek
Vivotek SD9366-EH-v2 Bedienungsanleitung
Vivotek
Vivotek Supreme IP8151 Kurzanleitung
Vivotek
Vivotek FD8133 Bedienungsanleitung
Vivotek
Vivotek IP3137 Bedienungsanleitung
Vivotek
Vivotek TD5196A Bedienungsanleitung
Vivotek
Vivotek IP8160-W Bedienungsanleitung
Vivotek
Vivotek IB8156-C Bedienungsanleitung
Vivotek
Vivotek PZ8111 Bedienungsanleitung
Vivotek
Vivotek IB9371-HT Bedienungsanleitung
Vivotek
Vivotek IP8371E Bedienungsanleitung
Vivotek
Vivotek SUPREME MA9321-EHTV Bedienungsanleitung
Vivotek
Vivotek FD8138-H Bedienungsanleitung
Vivotek
Vivotek VORTEX FD837-HTV Bedienungsanleitung
Vivotek
Vivotek IZ9361-EH Bedienungsanleitung
Vivotek
Vivotek FD8137HV Bedienungsanleitung
Vivotek
Vivotek 2M Bedienungsanleitung
Vivotek
Vivotek IB9387-EHT-A Bedienungsanleitung
Vivotek
Vivotek 3GPP IP7131 Bedienungsanleitung
Vivotek
Vivotek PZ8111 Bedienungsanleitung
