VOGELS PFW6852 Bedienungsanleitung

MOUIN_PFW6852_V03

Max: 136kg/300lbs

PFW 6852

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione,

Guide d’Installation, Installatie gids

M6 or 1/4"

Wood Drill bit

3/8" Masonry

Drill bit

13mm or 1/2"

Socket

Swingout Mount Universal Bracket

Bar

5/32" Allen

Wrench

14mm Socket Level

Mounting

Bracket

Griplate™

Washer

5/16" Flat

Washer

Universal

Spacers

Thread Depth

Indicator

(Supplied)

Extension

Adapter

M8 Nylon Nut

5/16" x 3"

Hex Lag

M4 x 16mm M4 x 20mm M4 x 30mm

M6 x 16mm

M8x 16mm M8 x 20mm M8 x 30mm

M10 x 30mm

M6 x 20mm M6 x 30mm

x1 x1 Pair

x10

x4 x4 x4

x8x4 x4 x4

x1 x1x4 x4 x4

x6 x1

Finned

Anchor

Maximum Flat Panel Weight:

300 lb. / 136 kg.

PFW 6852

www.vogels.com | Europe +31 (0)40 26 47 400

Page 2

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

Required for installation

Included Components:

www.vogels.com | Europe +31 (0)40 26 47 400

Page 2

PFW 6852

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

PFW 6852

www.vogels.com | Europe +31 (0)40 26 47 400 Page 3

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

Mount Orientation

Nose Piece Orientation

Left-Hand Swingout Orientation

Right-Hand Swingout Orientation

Tension Bolt Nuts

and Washers

Tension Bolt Nuts

and Washers

Tension Bolts

Nose Piece

The Nose Piece consists of four parts that must stay together in the order that they were manufactured. If they become separated during

any of the Nose Piece Orientation steps, re-assemble the parts in the order shown below.

Outer Radial Bearing

Outer Radial Dish

Inner Radial Dish

Inner Radial Bearing

Proceed to the “Wood Stud Installation” section if installing on a wood stud surface. The drywall must be at least 1/2” thick.

Proceed to the “Concrete Installation” section if installing onto a concrete surface.

Left-Hand Swingout Arm Orientation Right-Hand Swingout Arm Orientation

Nose Piece

Upright Orientation

Swingout Arm can be oriented to open from either the left-hand or right-hand side. Simply invert and re-orient the Nose Piece.

Proceed to the “Nose Piece Orientation” section.

1) Remove the Nose Piece by removing the tension bolts, tension bolt nuts, and washers.

2) Detach the Nose Piece assembly, rotate it 180°, And place it back onto your Swing out Arm.

3) Slide the tension bolts back into the holes and attach the tension bolts nuts and washers from the backside of the Nose Piece Assembly.

4) Tighten the tension bolts.

Do not overtighten the tension bolts.

www.vogels.com | Europe +31 (0)40 26 47 400 Page 3

PFW 6852

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

Secure the mount to two (2) wall studs with all six (6) 5/16" x 3"

hex lag into the studs.

Minimum of two (2) 2 x 4 wood stud to be used

Do not overtighten.

Wood Installation

Two people are recommended for this step; one person to level

the Mount and another person to mark the wall stud location.

Drill a “pilot hole” in the center of the upper right mark using a 1/4" drill

bit and power drill.

Only use a 1/4" drill bit when drilling pilot holes.

Install all six mounting points. Use a 5/16" washer on each hex lag.

Left-Hand Swingout Arm Orientation Right-Hand Swingout Arm Orientation

Pivot

Side

Pivot

Side

A B

CB A

D D

1) Place the mount against the wall in the desired viewing location.

2) Adjust the mount to align the mount slots in the wall plate with the

center of the wall studs.

3) Level the mount.

4) Use a pencil to mark the upper right mounting location along the center

of the wall stud.

PFW 6852

www.vogels.com | Europe +31 (0)40 26 47 400

Page 4

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

www.vogels.com | Europe +31 (0)40 26 47 400

Page 4

PFW 6852

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

1) Place the Mount against the wall and align it with the pilot hole.

2) Insert one (1) 5/16" x 3˝ hex lag and one (1) 5/16" washer into the

upper right pilot hole.

3) Use a socket wrench and a 1/2" socket to tighten the hex lag.

Do not overtighten the hex lags.

1) Level the wall plate.

2) Use a pencil to mark the remaining ve (5) mounting locations

along the center of each wall stud.

Two people are recommended for this step; one person to level

the wall plate and another person to drill the pilot holes.

Drill a “pilot hole” in the center of each of the marks with a

power drill and a 1/4" drill bit.

Only use 1/4" drill bit when drilling the pilot holes.

1) Insert one (1) 5/16" x 3" Hex Lag and one (1) 5/16" washer into each pilot

hole

2) Tighten all hex lags using a socket wrench and 1/2" socket.

Do not overtighten the hex lags when attaching the mount to the wall.

Improper installation may result in personal injury or property damage.

PFW 6852

www.vogels.com | Europe +31 (0)40 26 47 400 Page 5

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

www.vogels.com | Europe +31 (0)40 26 47 400 Page 5

PFW 6852

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

PFW 6852

www.vogels.com | Europe +31 (0)40 26 47 400

Page 6

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

Two people are recommended for this step: one

person to level the wall plate and another person to

mark the mounting locations.

Concrete Installation

5/16" Flat Washer 5/16" x 3" Hex Lag

x6 x6

Insert the hex lags and washers into the Finned anchors.

Tighten all hex lags using a socket wrench and 1/2″ socket.

Do not over tighten the hex lag.

Drill six (6) pilot holes of each mark using a drill and 3/8”

masonary drill bit. Drill 3 inches deep.

Only use a 3/8" masonary drill bit when drilling pilot holes.

Insert a Finned Anchor into each hole. Lightly tap each Finned

Anchors into place with a hammer.

Finned Anchor

www.vogels.com | Europe +31 (0)40 26 47 400

Page 6

PFW 6852

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

Small Straw

or Toothpick Depth Plus 1/8” Allowance

Mark

Depth Plus 1/8” Allowance

Mark

Small Straw or Toothpick

Marking the 1/8”

Allowance

Account for the bracket, spacer and Griplate™ Depths when

using the Thread Depth Indicator to measure the thread

depth of the at panel.

PFW 6852

www.vogels.com | Europe +31 (0)40 26 47 400 Page 7

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

Selecting the Mounting Hardware

1) Insert a small straw or toothpick into the threaded inserts found on the

back of the at panel.

2) Use a pencil to mark the depth of the threaded insert on the small straw

or toothpick.

3) Mark the straw or toothpick 1/8" above the depth of the threaded insert,

as shown in Figure 1.

4) Insert the small straw or toothpick into the remaining threaded inserts to

compare verify their depth using the straw or toothpick's 1/8 allowance mark.

5) Locate the correct diameter screw for the threaded insert.

6) Test each size of the screws provided.

The correct screws should thread easily into the mounting point and not

pull out when tension is applied.

If the screw selected is longer than the 1/8" allowance

mark on the small straw or toothpick, as shown in Figure

2 and Figure 3, do not use this screw. The screw length

must not bypass the mark.

www.vogels.com | Europe +31 (0)40 26 47 400 Page 7

PFW 6852

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

Universal Spacer Installation (Optional)

Griplate™ Washer Installation

Premier Mounts’ Griplate™ washers are designed to accommodate the

various M4, M5, M6 and M8 hole sizes required by at panels.

Do not place excessive pressure on the back of the at panel, as

this may damage your at panel.

The Griplate™ washer must be installed between the head of the

mounting screw and the mounting bracket as shown.

The dimples on the Griplate™ washers must be oriented as

follows:

- The Griplate™ Washers installed at the top of the at panel must

have the points of the dimples facing away from the at panel.

- The Griplate™ Washers installed at the bottom of the at panel must

have the points of the dimples facing towards the at panel.

- Recessed mount points?

- Uneven mounts points?

- A curved back?

- Any obstruction near the mount point?

If Yes, install the Universal Spacer. Proceed to the "Universal Spacer

installation" section.

If No, skip to the "Mounting Bracket Installation" section.

Flat Panel

Griplate™ Washer

Universal Spacer

Mounting Bracket

Mount Point

Mounting Screw

Griplate™

Flat Panel

Mount Point

Bracket

Top Griplate™

Dimple Orientation

Bottom Griplate™

Dimple Orientation

1˝ ¼˝

Universal Spacers allow the user to attach the mounting bracket

to at-panels which have recessed or uneven mount points. Each

Universal Spacer adds 1/4” to the distance between the mounting

bracket and the at-panel.

The Universal Spacers must be stacked and oriented as

shown.

The Universal Spacers must only be installed between the

mounting bracket and the at-panel.

Does the at panel have:

PFW 6852

www.vogels.com | Europe +31 (0)40 26 47 400

Page 8

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

www.vogels.com | Europe +31 (0)40 26 47 400

Page 8

PFW 6852

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

Does the at panel have a mount pattern for the mount points greater

than 506mm high x 876mm wide?

If No, proceed to the “Universal Bracket Installation” section.

If Yes, proceed to the “Adapter Plate Installation (Optional)” section.

The Adapter Plates allow the mount to accommodate varies mount patterns.

Without Adapters:

Minimum: 240mm x 120mm

Maximum: 506mm x 876mm

With Adapters:

Minimum: 200mm x 200mm

Maximum: 985mm x 667mm

Universal Bracket

Universal Brackets

Universal Bracket Installation

1) Place the Universal Bracket Bar and the Universal Brackets on a at surface.

2) Slide the Universal Brackets onto the Universal Bracket Bar with the set

screws facing up.

1) Place the at panel on a soft, at surface, face-down.

2) Place universal spacers over pointing points, as determined in the "Universal

Spacer Installation" section.

3) Place the Universal Bracket assembly on the back of the display, with the

Universal Brackets resting directly over the at panel mount points.

4) Place a Griplate™ Over each mount point and secure them using the mounting

hardware determined in the "Selecting the Mounting Hardware" section.

Do not tighten the set screws that are located on the

back of each Universal Bracket.

PFW 6852

www.vogels.com | Europe +31 (0)40 26 47 400 Page 9

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

www.vogels.com | Europe +31 (0)40 26 47 400 Page 9

PFW 6852

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

Set Screws

1) Center the Universal Bracket Bar.

2) Use the 5/32" Allen wrench to tighten the set screws that are

located on the back of each Universal Bracket.

Do not overtighten the set screws.

Adapter Plate Installation

Universal Bracket Bar

Universal Brackets

Slide the Universal Brackets onto the Universal Bracket Bar with the set

screws facing up.

Caution!

Do not tighten the set screws that are located on the back of

each Universal Bracket.

If M10 x 30mm mounting screws are needed for your installation,

Griplate™ washers cannot be used. Please use the four (4)

5/16" at washers (supplied) with the M10 x 30mm screws to

attach the adapter plates to the at panel.

Attach the Adapter Plates to the at panel using Griplates™ and the

mounting hardware determined in the “Selecting the Mounting

Hardware” and “Nylon Spacer Installation” sections.

Do not tighten the mounting hardware at this time.

PFW 6852

www.vogels.com | Europe +31 (0)40 26 47 400

Page 10

Installation Guide

Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d’Installation, Installatie gids

www.vogels.com | Europe +31 (0)40 26 47 400

Page 10

Andere Handbücher für PFW6852

Inhaltsverzeichnis

Andere VOGELS Rack & Stand Handbücher

VOGELS

VOGELS SoundMount NEXT 8365 Installationsanleitung

VOGELS

VOGELS PFW 6885 Bedienungsanleitung

VOGELS

VOGELS NEXT 7356 Bedienungsanleitung

VOGELS

VOGELS W50050 Bedienungsanleitung

VOGELS

VOGELS THIN 445 Bedienungsanleitung

VOGELS

VOGELS SWM 4111 Series Bedienungsanleitung

VOGELS

VOGELS NEXT 7346 Bedienungsanleitung

VOGELS

VOGELS THIN 305 Bedienungsanleitung

VOGELS

VOGELS TVM 5405 Series Bedienungsanleitung

VOGELS

VOGELS EFW 8405 Bedienungsanleitung

VOGELS

VOGELS THIN 595 Bedienungsanleitung

VOGELS

VOGELS WALL 1325 Bedienungsanleitung

VOGELS

VOGELS SOUND 4113 Bedienungsanleitung

VOGELS

VOGELS MA 3010 Series Bedienungsanleitung

VOGELS

VOGELS PLW 1003 Bedienungsanleitung

VOGELS

VOGELS W50060 Bedienungsanleitung

VOGELS

VOGELS PPC 1540 Bedienungsanleitung

VOGELS

VOGELS EFW 8405 Bedienungsanleitung

VOGELS

VOGELS TVB 2250 Bedienungsanleitung

VOGELS

VOGELS WALL 1025 Bedienungsanleitung

VOGELS

VOGELS EFW 8105 Bedienungsanleitung

VOGELS

VOGELS EFW 6245 - EFW 6145 EFW 6345 Bedienungsanleitung

VOGELS

VOGELS EFA 8825 Bedienungsanleitung

VOGELS

VOGELS W52080 Bedienungsanleitung

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung