Von Duprin 33 Bedienungsanleitung

Installation Instructions

33/3549A

CS 33/3549A

Printed in U.S.A.

24795379 Rev. 04/14-a

FOR DEVICES SOLD

PRIOR TO

4-14-14

Customer Service

1-877-671-7011 www.allegion.com/us

2-Point

Latch

includes

these

additional

parts

1-Point

Latch

(LBL)

= for Aluminum Door applications

= for Hollow Metal Door applications

= for Hollow Metal Door Retrofit applications

This instruction covers new installation of the 33/3549A

concealed vertical device for aluminum and hollow metal

doors.

Also covered is the CS 33/3549A retrofit cabling system

for converting 33/3547A Series to 33/3549A Series

(compatible with models 33/3547A, 33/3547A-F,

33/3547A-LBR, and 33/3547A-F-LBR).

2Install Cable(s).

c. Push cable snap against center slide to secure cable

b. Pull cable into clip to snap it into place

a. Position red cable end to clip on center slide

d. In the same way, install opposite end of red cable to top latch in the

position marked red

aclip Red

cable snap

A cable removal tool has been provided. Slot in tool fits over cable,

holding tabs down. Pull on cable snap to loosen cable for removal.

cable

snap

slot

CABLE REMOVAL

Ensure cable end is

fully seated in clip

IMPORTANT:

For 2-Point Latch Only

f. Install opposite end of white cable to bottom latch

e. There is an adjuster on one end of the white cable. Install this end to the

remaining top latch position (marked as white)

Ensure cable end is

fully seated in clip

IMPORTANT:

1Identify Cables and Locations. NOTE: For retrofit installations,

begin at Step 5.

(if not preinstalled in door)

For easy identification,

each cable is labeled

with part number and

location.

6' 8"

7' 0"

8' 0"

9' 0"

10' 0"

23925803

Top Cable (Red)

23925647

23925522 23925522

23925407

23925761

23925647

23925407

23925761

CABLE IDENTIFICATION (STANDARD SIZES)

HOLLOW METAL AND

WIDE STILE ALUMINUM DOORS

NARROW STILE

ALUMINUM DOORS

Door Opening

Height Bottom Cable (White)

23926058 23926058

23925936

23925811

23926173

23925936

23925811

23926173

2392621523925795 23926207

Bottom Cable (White)

White e

adjuster

3Determine if Bottom Latch Retraction Adjustment is

Necessary.

For 2-Point Latch Only

a. Flex the cable into an L-shape as shown to simulate the installed

condition of the latches.

top latch

(hold-open

position)

bottom latch

(retracted)

¹⁄₁₆"

flush

press

b. To determine whether an adjustment is required, actuate the top

latch to the hold-open position by pressing down on the connecting

rod. Bottom latch should retract to within ¹⁄₁₆" of flush. If it does not,

an adjustment is necessary.

4Adjust Bottom Latch Retraction (if necessary).

For 2-Point Latch Only

d. While holding the snap-fitting

with a ³⁄₈" wrench, continue to

tighten the locknut until it is

secure.

c. While holding the conduit cap

with a ³⁄₈" wrench, use a 10mm

wrench to turn the locknut in a

clockwise direction to close the

gap between the lock nut and

snap-fitting. Stop when the gap

is closed and the snap-fitting

begins to turn with the locknut.

a. While holding the snap-fitting

with a ³⁄₈" wrench, use a 10mm

wrench to break loose the lock

nut.

b. While holding the lock nut in

place, rotate the barrel of the

snap-fitting clockwise by hand

until the bottom latch is

retracted to within ¹⁄₁₆" of flush.

bottom latch

(retracted)

¹⁄₁₆"

flush

snap-fitting

locknut

conduit cap

NOTE: Adjustment must be made while the top

latch is in the hold-open position, with cable

flexed into an L-shape to simulate the installed

condition of the latches.

These (3) hex

components

are used to

make the

adjustment.

snap-fitting

³⁄₈"

10mm

³⁄₈"

conduit

cap

lock nut

10mm

³⁄₈"top latch

If no adjustment is

needed, proceed

to Step 5.

7Align Paper Template to Mark and Prepare Door, if

Required.

6With Door Laying Flat, Draw Horizontal and Vertical

Device Center Lines ( ).

RHR shown

(LHR opposite)

See template

for Backset

5If Retrofit Installation

a. Remove device

from existing

door.

b. Remove and

discard existing

door.

c. Remove and

discard existing

strikes.

RHR shown

(LHR opposite)

See pages 11 and 12

for paper templates.

NOTE: Centerlines are predetermined by cutout. If no

cutout exists, refer to templates at the back of this

instruction to determine centerlines.

9Prepare Access Hole for Bottom Latch Adjustment

Pin.

3¹⁵⁄₁₆"

⁵⁄₈" from

push side

of door

Bottom of Door Door Edge

RHR

⁵⁄₈" from

push

side of

door

Door Edge

LHR

³⁄₄" Dia.

hole

4¹⁄₄" depth

clearance

required

Door Door

Hollow Metal For 2-Point Latch Only

8Assemble Latch Mounting Brackets.

Top

Bottom

For 2-Point Latch Only

Top Door Channel

3/4"

1/4"

3/4"

1/4"

1/4"3/4"

Hollow Metal

³⁄₄" mounting

shown

13 If Using 360/386/388 Thru-Bolting Trim, Remove

Center Slide Mounting Nut.

mounting nut has

left-handed

threading

³⁄₈" socket

with ¹⁄₄" drive

center slide

mounting nut

Thru-bolting trim

uses standoffs

(360L trim shown)

12 Prepare Bottom of Door for Latch Mounting.

Latch

1¹⁄₂"

2¹⁄₄"

⁷⁄₃₂" Dia. x2

82˚ Csk to ³⁄₈" Dia.

Push Side of Door

Aluminum For 2-Point Latch Only

11 Prepare Top of Door for Latch Mounting.

Latch

1¹⁄₂"

3⁷⁄₁₆"

⁷⁄₃₂" Dia. x2

82˚ Csk to ³⁄₈" Dia.

Push Side of Door

Aluminum

10 If Necessary, Prepare Door for Top Strike Cutout.

1¹⁄₄"

⁹⁄₁₆"

Cut out material

this side only

Latch

Push side of door, RHR shown

NOTE: Confirm top latch (and bottom latch, if applicable) is in correct orientation before proceeding.

NOTE: It is normal for the

cable to bend inside the door,

forcing the latch outward.

14 Slide Latch and Center Slide Assembly thru Door.

Top

Aluminum Door application shown

2-Point Latch

1-Point Latch (LBL)

Top

Holes should face

push side of door

Holes should face

push side of door

Holes should face

push side of door

15 Secure Center Slide to Door.

Secure center slide to

door by lightly

tightening lower screw

Align upper hole

visually

Insert small screwdriver

into upper hole to

prevent center slide

from rotating

Fully tighten lower

screw

16 Align Bottom Latch and Install Mounting Screws.

Aluminum For 2-Point Latch Only

18 Install Bottom Latch Mounting Bracket Assembly.

Hollow Metal For 2-Point Latch Only

NOTE: Use 2 screws per

bracket (center hole not

used for this application).

#25

#10-24

Push Side

of Door

NOTE: Confirm correct orientation of

assembly before proceeding. Open side of

housing should face pull side of door.

If using

³⁄₄" undercut door

spacer blocks (2)

are required

Spacer Block Kit

(24231516)

purchased separately

17 Secure Top Latch with 2 Screws.

Aluminum

22 If Necessary, Cut Device.

Door

1¹⁄₂" (38 mm)

Recommended

Jamb

Cover Plate

Flush

Temporarily Remove

Anti-Rattle Clip

23 Attach Center Case to Door.

Sex Bolt

Thru-bolting Trim

Block may need to

be pushed down

to insert screw

(1³⁄₄" door)

(2¹⁄₄" door)

(Bottom hole only)

(1³⁄₄" door)

(2¹⁄₄" door)

Top mounting screw is secured

into upper hole of center slide

NOTE: If using 360/386/388

trim, this screw will pass

thru top center slide hole

and secure directly into trim.

21 Hang Door on Frame.

CAUTION: For 2-point latches, bottom latch cannot be in locked

position while hanging door on frame. Latch must be retracted.

Insert Latch Adjustment Pin to Hold Bottom Latch

in Place.

Hollow Metal For 2-Point Latch Only

Pin must

go thru

both sides

of bracket

Bottom edge of latch

housing should be flush

with bottom of door (for

³⁄₈" standard undercut)

Squeeze tabs on

cap, then insert pin

Assemble pin

20 Secure Top Latch Mounting Bracket.

#25

#10-24

NOTE: Use 2 screws per

bracket (center hole not

used for this application).

NOTE: It is normal for

the cable to bend

inside the door, forcing

the latch outward as

shown here.

Hollow Metal

28 Install 2 Top Strike Screws Using the Slot Features

on the Strike.

29 Prepare Floor for Bottom Strike.

Hollow Metal For 2-Point Latch Only

⁷⁄₈"1" 1"

⁷⁄₈"

¹⁄₂"

³⁄₈" Dia. x 1¹⁄₄" Deep

2 places

Chisel out pocket

¹⁄₂" Deep

Latch

Push Side

Pull Side

27 If Retrofit Installation, Install Steel Cover Plate to

Cover Existing 338 Strike Opening in Accordance

with the Frame Manufacturer’s Fire Listing.

249 Top Strike

Retrofit installation

(metal)

(wood)

Strike Filler Plate

(3FP0116A001-GL)

purchased separately

25 Install End Cap Bracket and End Cap.

Surface Mount or Sex Bolts

(1³⁄₄" door)

Sex Bolts

(2¹⁄₄" door)

26 If New Installation, Prepare Door Frame for Top

Strike.

24 Mark and Prepare 2 Holes.

Surface Mount (metal doors only)

Sex Bolts

¹⁄₄" (device side)

¹³⁄₃₂" (trim side)

#25 #10-24

Edge

stop

¹⁄₂"

Use strike to

mark location

of 2 holes

Latch

Metal

Wood

#25 x ¹⁄₂" Deep x2

#10-24

¹⁄₈" Drill

Pilot 1" Deep x2

30 Install Bottom Strike.

Clear holes of debris, then

drop in anchors (slotted end

first)

Secure the anchors using a

hammer and punch

Install strike plate and secure

with 2 screws

Hollow Metal For 2-Point Latch Only

349 Bottom Strike

bIMPORTANT:

Anchors must

be below flush.

31 Prepare Threshold.

Aluminum For 2-Point Latch Only

a. After closing door with bottom latch installed, mark the location the

bottom latch bolt is contacting the threshold.

b. Drill a ³⁄₄" diameter hole in the threshold.

Stop

³⁄₄" Dia.

Latch

Latch bolt

33 Adjust Lift Finger.

Loosen retainer clip

screw

Loosen adjustment

screw until the lift

finger drops and

you feel contact

with the center

slide

Tighten retainer clip

screw

32 Install Lift Finger and Retainer Clip.

Slide L-shaped lift finger thru block in

device center case and then into

center slide

Insert adjustment

screw through top

slot and rotate

with screwdriver

to raise lift finger

until it is snug

against block

Secure lift

finger and

retainer clip

with screw

slot

Lift finger must insert

into center slide here

For 2-Point Latch Only

Push cable to the side

so it does not interfere

with lift finger.

Install retainer clip against

lift finger, snapping it

into the slot of the

adjustment screw

NOTE: The lift finger installation and adjustment must be performed

while the latches are in the extended (latched) position.

NOTE: Lift finger adjustment must be performed while

the latches are in the extended (latched) position.

34 Perform Functional Test of Door.

For 2-Point Latch Only

a. Depress pushbar. Door should begin to open when pushbar is nearly

fully depressed. If necessary, refer to Step 33 to readjust lift finger.

b. With door closed, top latch should be secure.

c. With door closed, bottom latch should be secure.

d. Confirm that bottom latch does not drag against floor when door is

opened.

If this occurs, remove latch adjustment pin and raise latch, then reinsert

pin in next notch.

Pin must go thru

both sides of bracket

Hollow Metal For 2-Point Latch Only

Squeeze tabs

on cap before

reinserting pin

To remove pin, slide a

screwdriver beneath the

latch adjustment pin cap

1. Remove mortise cylinder cam and reinstall in reverse (Figure 1).

2. Insert key and rotate cam to install the cylinder to the cover plate (Figure 2).

3. Remove key to slide cover plate in position in the mechanism case.

Std. mortise

cylinder

Mortise

cylinder cam

Std. mortise

cylinder

Mortise

cylinder cam

CD function conversion

Dogging procedure

Turn cylinder key approximately ¹⁄₈

turn for standard dogging

Depress pushbar

Figure 1

Figure 2

Std. mortise

cylinder

Offset toward

pushbar

Dogging plate

cover

Cylinder collar

Cylinder

locking washer Cylinder

locking nut

Mechanism

case

OPTIONAL EQUIPMENT

CD (CYLINDER DOGGING)

Remove protective film

from pushbar

36 Install Center Case Cover.

35 Adjust Top Strike as Necessary, then Install the

Third Strike Screw to Fix the Strike Position.

Metal

Wood

#25 x ¹⁄₂" Deep

#10-24

¹⁄₈" Drill

Pilot 1" Deep

(metal) (wood)

Andere Handbücher für 33

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Von Duprin Türschloss Handbücher

Von Duprin

Von Duprin 98 Bedienungsanleitung

Von Duprin

Von Duprin 6225 Bedienungsanleitung

Von Duprin

Von Duprin 22 Series Bedienungsanleitung

Von Duprin

Von Duprin StrikeForce 6210 Bedienungsanleitung

Von Duprin

Von Duprin 98 Series Bedienungsanleitung

Von Duprin

Von Duprin CX33A Bedienungsanleitung

Von Duprin

Von Duprin 5100 Bedienungsanleitung

Von Duprin

Von Duprin 33 Bedienungsanleitung

Von Duprin

Von Duprin M996L Series Bedienungsanleitung

Von Duprin

Von Duprin 6212WF Bedienungsanleitung

Von Duprin

Von Duprin 990 series Bedienungsanleitung

Von Duprin

Von Duprin StrikeForce 6210 Bedienungsanleitung

Von Duprin

Von Duprin 6226 Bedienungsanleitung

Von Duprin

Von Duprin StrikeForce 6211WF Bedienungsanleitung

Von Duprin

Von Duprin 940L Bedienungsanleitung

Von Duprin

Von Duprin 230L-BE Bedienungsanleitung

Von Duprin

Von Duprin 376-T Bedienungsanleitung

Von Duprin

Von Duprin 375-L Bedienungsanleitung

Von Duprin

Von Duprin 6300 Bedienungsanleitung

Von Duprin

Von Duprin 99 Bedienungsanleitung

Von Duprin

Von Duprin 6111 Bedienungsanleitung

Von Duprin

Von Duprin 377-T Bedienungsanleitung

Von Duprin

Von Duprin 6211AL Bedienungsanleitung

Von Duprin

Von Duprin (AX) 98/99-2 Bedienungsanleitung

Beliebte Türschloss Handbücher anderer Marken

Assa Abloy

Assa Abloy effeff 827A-IP Bedienungsanleitung

We.lock

We.lock SECBNEBL51 Bedienungsanleitung

Iseo

Iseo MA1A Bedienungsanleitung

ID Lock

ID Lock 150 Bedienungsanleitung

Lockly

Lockly ACCESS TOUCH PRO Bedienungsanleitung

iLoq

iLoq G50S Bedienungsanleitung

SDC

SDC Z7835 Bedienungsanleitung

ilco

ilco 452 Bedienungsanleitung

Samsung

Samsung shs-h705 Bedienungsanleitung

TRU-BOLT

TRU-BOLT 08102017 Bedienungsanleitung

CDVI

CDVI 500-LADJ Bedienungsanleitung

Igloohome

Igloohome Deadbolt 2S Metal Grey Montage- und Wartungsanleitung

eSSL

eSSL FL-300 Bedienungsanleitung

JAKO

JAKO JKBTNX4 Bedienungsanleitung

Dorma

Dorma MUNDUS PREMIUM GK 50 Benutzerhandbuch

SCOOP

SCOOP Pullbloc 4.1 FS Panik Bedienungsanleitung

Yale

Yale MORTISE 8800 SERIES Bedienungsanleitung

Siegenia

Siegenia KFV AS3500 Bedienungsanleitung