VPI Industries JMW-9T Bedienungsanleitung

VPI Scoutmaster /JMW-9T

Turntable

Setup and Instruction Manual

VPI Industries, Inc., 77 Cliffwood Ave. #3B, Cliffwood, NJ 07721

Phone: 732-583-6895 Email: Sal[email protected]

http://www.vpiindustries.com

Important: Read Before Proceeding!

Read and follow the Safety Instructions below.

Save all packing materials. The Scoutmaster should only be moved or shipped

in its original packaging to reduce the risk of damage in transit.

The Scoutmaster must be placed on a flat, level surface. This will make setup

easy, provide better sound quality, and put less strain on the main bearing.

Safety Instructions

Follow the instructions below to reduce risk of electrical

hazard or injury.

1. To avoid electrical shock, do not open the motor housing.

2. If the power cord provided with the Scoutmaster does not reach an outlet, use

a heavy-duty, grounded extension cord.

3. To avoid electrical shock, always plug the Scoutmaster into a grounded outlet.

4. Do not expose the Scoutmaster to rain or excessive moisture.

5. Do not touch the male pivot point of the tonearm assembly. It is extremely

sharp.

Introduction

The Scoutmaster turntable is a precision instrument. It has been thoroughly

tested and run for at least 4 hours. The speed accuracy, wow, flutter, and rumble

have been checked, and this unit meets all of our specifications.

Minimum Specifications

Wow and flutter Less than .02%.

Rumble Greater than 80db down.

Speed accuracy Within .1%.

Total weight 57 pounds.

Platter runout +/- .001 inch.

Unpacking the Box

The turntable and tonearm are packed very carefully to avoid damage during

shipping. It is important that you save the packing materials and box to use for

shipping or moving the Scoutmaster.

Remove the 2 pieces of cardboard.

Set aside the bag containing the drive belt.

Complete and return the warranty card. The

warranty does not take effect until the

warranty card is returned.

Remove and set aside the these items:

Alignment Jig.

Record clamp.

Power cord.

Bag containing screwdrivers and screws for mounting the cartridge.

Remove the foam pieces that surround the chassis. Lift one side of the

turntable chassis, slide off the plastic bag, then do the same with the other

side of the chassis.

Remove the turntable chassis from the box.

Remove the turntable platter and motor. Be very careful not to hit or damage

the motor pulley. It measured +/- .0005” when it was tested at the factory.

Try not to disturb it at all.

Remove the pieces of foam covering the tonearm, then carefully remove the

tonearm and set it down in a safe place. Use caution with the tonearm’s

delicate wires and Lemo connector.

Setting up the Scoutmaster

The Scoutmaster must be placed on a flat, level surface. This will make setup

easy, provide better sound quality, and put less strain on the main bearing.

Place the turntable chassis, with the square cutout on the left, on the shelf or

stand where it will be used. The better isolation you provide the Scoutmaster

2, the better it will sound. You can get very good isolation by placing the

Scoutmaster 2 on a maple butcher block cutting board about 2” thick sitting

on 4 squash balls in ash trays. Very inexpensive and easy to find.

Remove the tape from the spindle hole on the turntable platter and place the

platter on the spindle. The platter bearing is lubricated; no additional

lubrication is needed for at least one year.

Connect the power cord to the motor, and then place the motor, with the

power cord at the rear, next to the square cutout of the turntable chassis.

Lift the chassis and place it over the power cord. The motor should extend

approximately .25 inch from the side of the turntable chassis.

Place the drive belt around the platter and around the pulley on the motor.

The belt does not have to be level on the platter. It will self-level when the

platter starts rotating.

For 33 RPM operation, place the belt on the upper part of the pulley. For 45

RPM operation, place the belt on the lower, wider part of the pulley. The

center groove in each diameter is usually the correct speed. To determine the

precise speed, use a strobe disc and adjust speed by moving the belt up or

down. The VPI Synchronous Drive System speed controller provides the

ultimate speed accuracy and best sound. Check with your dealer about

availability.

Verify the turntable is level by using a 9- or 12-inch bubble level front-to-back

and side-to-side on the platter. If it is not level, rotate the aluminum cone feet

up or down. If you must turn the Scoutmaster feet more than three full turns,

level the shelf or platform the table sits on first.

Installing and Aligning the Cartridge

Remove the protective cover from the male pivot point on the arm base

assembly.

To avoid injury, do not touch the male pivot

point. It is extremely sharp. In addition, skin

oils can blemish and cause corrosion to the

assembly.

Place the JMW-9T arm wand on its side on a foam pad.

For cartridges with threaded mounting holes, use the screws supplied by the

cartridge manufacturer. Other screws may not fit properly and may cause

damage to the threads and cartridge.

To avoid damage to the tonearm, use one of the washers supplied by VPI

under the screw heads.

For cartridges with pass-through mounting holes, use the hardware supplied

with the tonearm. Be sure to use washers under the screw heads.

The tonearm wires are color-coded as follows:

Red right hot.

Green right ground.

White left hot.

Blue left ground.

If your phono section inverts phase, the hot color becomes the ground color.

Using tweezers or fine-tipped pliers, grip the center of the red wire’s connector

not the wire itself and push it onto the cartridge’s right hot terminal pin.

Connect the remaining connectors in the same way.

To avoid damage to the cartridge, do not push the connectors all the way on.

Adjust the tonearm counterweight halfway back on its mounting to reduce the

amount of down force on the cartridge.

Place the JMW Memorial Tonearm Alignment Jig on the spindle with the narrow

end next to the pivot point. Tighten the screws of the jig so it fits snugly

against the male bearing shaft

Place the arm tube assembly on the lower pivot point, using caution with the

4-color wire and Lemo connector. Set the arm in its rest. If the cartridge has a

guard, remove it.

Line up the red dot on the Lemo connector with the red dot on the receptacle

on the junction box. The Lemo connector can plug in only one way and should

not be forced.

Swing the tonearm over the jig so the stylus is as close as possible to the dot

in the center of the grid. Set the counterweight for enough downward force to

keep the stylus from moving when resting on the jig.

Look down at the cartridge and align it between the lines of the grid. Be

careful to align the cartridge and not the tonearm headshell.

Adjust the cartridge mounting screws and the counterweight as needed until

the cartridge is centered between the grid lines and the stylus is resting on the

dot of the grid. The picture below shows the setup, the jig is in white for

clarity, yours is black.

When the cartridge is properly positioned, tighten the cartridge mounting

screws and remove the alignment jig.

Setting the Anti-Skating –Two Solutions

Anti-skating is one of the least understood forces acting on a tonearm. Skating

force is created by friction between the stylus and the record, causing a force

vector in a direction towards the center of the record when the headshell of the

tonearm has an offset angle. Putting a stylus down on a flat, groove less record

will cause the arm to move toward the center of the record. Arm manufacturers

have tried to compensate for this force, but that is impossible because the force

is constantly changing as the music and velocity change.

VPI has conducted careful listening tests and determined that every tonearm we

tried sounded better with its mechanical anti-skating set at the lowest possible

setting.

Adjust the counterweight so there is no down force on the cartridge.

Swing the tonearm toward the spindle and release it. The arm should swing

out toward the outer edge of the turntable if the anti-skating is working

properly. Set it as shown in the photo.

Setting the Tracking Force and Tonearm Height

Tracking force is adjusted by moving the tonearm counterweight forward and

back on its shaft. If your cartridge is heavy and the counterweight is all the way

back, you can order a heavier weight from your dealer.

The JMW Signature Tonearm does not have a built-in tracking force gauge. We

recommend that you use a Shure Stylus Force Gauge or good digital gauge.

Place the gauge on the platter with the notch against the spindle.

Follow the gauge instructions and set the tracking force according to the

cartridge manufacturer’s recommendation. We recommend always going to

the high side of tracking force (actually the high side plus .1 gram is the best).

High frequency vibrations on a light-tracking cartridge can cause more

damage to the grooves of a record than running a cartridge at a heavy

setting. The arm should be parallel to the platter when setting the tracking

force. If it is not parallel the reading will be off by enough to make a sonic

difference.

To adjust the arm height, loosen the two setscrews on the base of the arm

assembly, put a record on the platter, turn the adjustment wheel above the

base. When the arm is parallel to the record, tighten the screws. That is the

zero adjustment point and you should begin with the arm at that point. You

can lower the arm for more bass energy or raise the arm for more treble energy.

Setting the Azimuth

Place the 6” aluminum rod in the groove behind the mounting screws on the

tonearm headshell.

If it is not level, use the supplied Allen wrench to loosen the setscrew on the

counterweight and rotate the counterweight around the shaft until the

headshell is parallel to the record. Be careful not to change the tracking force

setting by moving the counterweight forward or back while rotating.

Playing Records

Before playing a record, make sure that all of the tonearm screws are tight.

Place the rubber washer on the platter spindle, then the record on the platter,

then screw the clamp onto the spindle. The clamp will lock the rim of the

record down first forcing the air out and acting like a vacuum.

Press the power button on the motor. Sit down and enjoy listening to your

records!

General Use

Allow at least 20 hours of break-in time.

The motors will make some low-level noise. This will not get into the system.

The motor and bearings will become quieter as you use your SM.

If you notice hum in the system, remove the interconnects and replace them

with very cheap, standard VCR interconnects. These are well shielded and

should eliminate the hum. If the hum goes away, get quality, well shielded

interconnects.

After at least one year of use, the platter bearing and motor will need to be

lubricated. For the platter bearing use a blob of white lithium grease placed on

the ball. For the motor, use 1 drop of 40-weight motor oil below the brass

piece.

Additional Items Available from Your Dealer

The VPI Synchronous Drive System power supply provides a major increase in

musicality by feeding the 300 RPM synchronous motor a perfectly stable wave

form at the frequency you choose. The SDS lets you change speed

electronically.

The HR-X periphery record clamp will fit the platter of the Scoutmaster and

provide a vacuum-like grip on the record. The clamp removes all warps and

damps the record to prevent ringing.

VPI Industries, Inc. Limited Warranty

VPI Industries, Inc. (VPI) warrants this unit against defects in materials and/or workmanship for

three (3) years from the date of purchase by the original retail purchaser. VPI’s sole obligation

under this warranty is limited to the repair or replacement, at VPI’s option, of any part(s) found

to be defective. VPI’s obligation to repair or replace defective parts is the purchaser’s sole and

exclusive remedy, and VPI shall not be liable for any direct or indirect injury and/or property

damage arising out of the use of the product or defect in or failure of the product.

This warranty does not extend to any unit whose serial number has been defaced or altered. Any

product that VPI determines causes a defect or malfunction due to incorrect installation,

modification, misuse, or servicing by the purchaser, or service technician not authorized by VPI to

perform such service will not be warranted. This warranty does not cover trivial or cosmetic

defects that do not impair the unit’s normal function.

VPI reserves the right to make changes in this product without assuming any obligation to install

such change in any product previously manufactured. This warranty to repair or replace defective

parts is in lieu of all other express or implied warranties of merchantability or fitness for a

particular purpose. There are not warranties that extend beyond the description herein.

Some states do not allow exclusion of implied warranties or limitation of incidental or

consequential damages, so the above exclusion or limitations may not apply to you. This warranty

gives you specific legal rights, and you may also have other rights that vary from state to state.

http://vpiindustries.com/warranty/

Inhaltsverzeichnis

Andere VPI Industries Drehscheibe Handbücher

VPI Industries

VPI Industries Classic Handbuch

VPI Industries

VPI Industries VPI JMW-3D Handbuch

VPI Industries

VPI Industries JMW 10 Handbuch

VPI Industries

VPI Industries ARIES 3 Benutzerhandbuch

VPI Industries

VPI Industries HW-19 JR Handbuch

VPI Industries

VPI Industries Signature 21 Bedienungsanleitung

VPI Industries

VPI Industries TNT HR-X Handbuch

VPI Industries

VPI Industries Classic 3 Handbuch

VPI Industries

VPI Industries Scoutmaster Handbuch

VPI Industries

VPI Industries Scout Jr. Handbuch

VPI Industries

VPI Industries JMW-9 Handbuch

VPI Industries

VPI Industries ARIES Benutzerhandbuch

VPI Industries

VPI Industries Nomad Handbuch

VPI Industries

VPI Industries PLAYER Bedienungsanleitung

VPI Industries

VPI Industries Signature DS Bedienungsanleitung

VPI Industries

VPI Industries TNT-4 AIR Handbuch

VPI Industries

VPI Industries HW-19 MK-4 Handbuch

VPI Industries

VPI Industries Scoutmaster Bedienungsanleitung

VPI Industries

VPI Industries JMW-9 Scout Tonearm Bedienungsanleitung

VPI Industries

VPI Industries VPI Classic 1 Handbuch

VPI Industries

VPI Industries TNT-5 Handbuch

VPI Industries

VPI Industries Classic Direct Handbuch

VPI Industries

VPI Industries Scout 2/JMW-9T Handbuch

Beliebte Drehscheibe Handbücher anderer Marken

Gemini

Gemini CDT-05 MKII Bedienungsanleitung

Rotel

Rotel RP-820 Bedienungsanleitung

Shuman

Shuman MC-250BT Bedienungsanleitung

Stanton

Stanton STR8-150 Bedienungsanleitung

Audio Technica

Audio Technica AT-LPW40WN Bedienungsanleitung

Crosley

Crosley McQueen CR7011-GY Bedienungsanleitung

Reloop

Reloop SMP-1 Bedienungsanleitung

auna

auna TT-Classic Plus Bedienungsanleitung

COMO AUDIO

COMO AUDIO Turntable Analog Bedienungsanleitung

Dual

Dual 1009 F Bedienungsanleitung

REED

REED Muse3C Bedienungsanleitung

AXIOMTEK

AXIOMTEK OPS883-H Series Bedienungsanleitung

Pioneer

Pioneer PL-71 Bedienungsanleitung

Vestax

Vestax PDX-a1 Bedienungsanleitung

Denon

Denon DP-400 Bedienungsanleitung

Dual

Dual 504 Bedienungsanleitung

Audio-Techica

Audio-Techica AT-LP60XBT Bedienungsanleitung

Goldring

Goldring G99 Bedienungsanleitung