Wacom CINTIQ 15X Bedienungsanleitung

CAUTION

Be sure to ground the power adaptor cable at the receptacle when plugging in.

Do not touch the liquid crystal if leaked; it is irritative. In case of contact, rinse immediately with running water

for more than 15 minutes. If it went into the eye or mouth, consult physician.

WARNING

Turn off the power of the Cintiq 15X in the area where prohibited to use. It may cause other electronic

devices to malfunction.

Do not use the Cintiq 15X in a facility control system that requires extremely high reliability. It may cause

other electronic devices to malfunction or, other device may cause the Cintiq 15X to malfunction.

Do not open the Cintiq 15X It has the risk of electric shock.

HIGH VOLTAGE

If the Cintiq 15X is broken due to fall or hit, do not leave it connected to the power. It has the potential to

result in fire.

Only use the AC adaptor that came with your Interactive Pen Display. If a different type of AC adaptor is used,

the Interactive Pen Display will not work properly or it may be damaged. Using a different type of AC adaptor

also has the potential to result in fire.

Prevent your children from swallowing the UltraPen nib or side switch. The pen nib or side switch may

accidentally be pulled out if children are biting on them.

UM-0251/CintiqAP.pm65 01.7.31, 9:27 PM1

Preface

The Wacom®Cintiq™15X is an integrated LCD tablet designed for direct draw-on-screen

interface with your computer. The Cintiq 15X Interactive Pen Display components include a

Wacom tablet internally mounted behind a 15.0" diagonal TFT color LCD monitor, and Wacom’s

UltraPen®.

This manual describes how to install the Cintiq 15X Interactive Pen Display hardware and

software.

It also describes how to use the Interactive Pen Display and UltraPen.

Information on using the Wacom Tablet Control Panel for customizing your tablet and pen

settings is available in the Interactive Pen Display online Help, located under the HELP menu in

the Wacom Tablet Control Panel.

The following are not included with this product:

■Information about your specific computer hardware.

■Information about your operating system.

■Information about application software. To use the pressure-sensitivity of the UltraPen with

your favorite drawing application, refer to instructions in that application’s manuals.

Please refer also to your computer hardware, operating system, or software application manuals.

UM-0251/CintiqAP.pm65 01.7.31, 9:27 PM2

Precautions on handling the Cintiq 15X

■For use with DVI, do not use any graphics card that Cintiq 15X can not be used with. It may damage

the Cintiq 15X.

■Do not disassemble the Cintiq 15X or pen. This may cause the device to malfunction. In this case,

Wacom shall have no responsibility to repair or replace the product.

■Do not use or store the Cintiq 15X where:

- Temperature changes are severe (e.g., outdoors or inside a vehicle).

- The Cintiq 15X and pen are exposed to direct sunlight or heat from an appliance.

- The Cintiq 15X and pen are exposed to water or any other kind of liquid.

- Temperature or humidity exceeds the specifications.

■Do not block the ventilation holes in the rear panel. It may overheat and damage the Cintiq 15X.

■Do not use the Cintiq 15X in a dusty environment. It may damage the Cintiq 15X.

■Do not scratch the cover glass of the Cintiq 15X. Avoid placing sharp objects on the glass surface. If the

pen tip becomes sharp or angular, it may damage the coating on the cover glass of the Interactive Pen

Display. Please replace the pen nib as necessary.

■Do not use detergent to clean the cover glass of the Cintiq 15X—this may alter the surface friction and

deteriorate the handwriting feel.

■Do not lift up the Cintiq 15X by holding the stand. It may damage the open-close mechanism of the stand.

When you lift up the Cintiq 15X, be sure to hold the main unit casing.

■Do not put heavy articles on the Interactive Pen Display; this may damage the cover glass or stand.

■Do not place heavy article on the Cintiq 15X cables. Near the cable connectors, do not apply heavy stress

on the cables or do not repeat bending the cables. It may damage the Cintiq 15X.

■Do not connect or disconnect the DVI video cable or power cable while the Interactive Pen Display or

your computer is turned on; it may damage the LCD display or computer video card.

UM-0251/CintiqAP.pm65 01.7.31, 9:27 PM3

Federal Communication Commission Interference Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of

the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential

installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with the instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference

to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to

try to correct the interference by one of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that

to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: To assure continued compliance, (example - use only shielded interface cables when connecting to

computer or peripheral devices). Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

Table of Contents

Checking Packed Components 5

Installation 6

LCD Monitor Installation

Wacom Tablet Software Installation for Windows and Macintosh

Calibrating the Tablet

Cintiq 15X Component Functions 10

Front View

Rear View

Mounting the Cintiq 15X onto a Mount Arm or Other Stand

Caring For Your Cintiq 15X

Using the UltraPen

UltraPen

Pen Type Settings in the Wacom Tablet Control Panel

Replacing the Pen Tip

Using the UltraPen 13

UltraPen

Using a Pen

Adjusting the LCD Monitor 15

Factory Presets, Auto Adjust and User Settings

Functions and Uses of the MENU Window

Adjusting Pitch and Phase

Power Saving

Caring For Your Cintiq 15X 19

Cleaning Your Cintiq 15X

Replacing the Pen Tip

Troubleshooting for Display 20

Specifications 22

General Specifications

LCD Display

Tablet

UltraPen

UM-0251/CintiqAP.pm65 01.7.31, 9:27 PM4

Checking Packed Components

In your package you will find the following items:

USB Cable or RS-232C Cable

DVI-DVI Cable or DVI-RGB Cable*2

Cintiq 15X

main unit

UltraPen with Pen Holder

User’s Manual

Wacom Software CD

Contains the Interactive Pen

Display software and a

Readme file

(Windows/Macintosh)

AC Adaptor and Cable

Side Slit

Fillers

*1*2

For Cintiq 15X only. Do not use this for other devices.

One either cable is included.

Please retain the package box for storage or transportation.

UM-0251/CintiqAP.pm65 01.7.31, 9:27 PM5

Installation

LCD Monitor Installation

First install the Cintiq 15X as a monitor. Do not connect the USB cable or serial data cable until instructed for

the tablet software installation.

➀Turn off your computer.

IMPORTANT: Never connect or disconnect the DVI video cable or power cable while your computer

or Interactive Pen Display is powered on. This can damage the LCD display or video card.

➁Connect the DVI-to-DVI cable or DVI-RGB cable between the Cintiq 15X and your computer.

➂Set the DVI / Analog RGB switch. Turn it up for Analog RGB, and turn it down for DVI.

√Connect the AC adaptor to the Cintiq 15X.

➄Connect the AC adaptor power cable and plug the adaptor into an AC outlet.

IMPORTANT

■Do not use any cable that did not come with

the Cintiq 15X. It may damage the Cintiq

15X.

■For use with DVI, do not use any graphics

card on which Cintiq 15X can not be used.

It may damage the Cintiq 15X.

■Do not connect or disconnect the DVI video

cable or power cable while the Interactive

Pen Display or your computer is turned on;

it may damage the LCD display or

computer video card.

DVI-I connector

DVI/analog RGB switch

DC input

USB connector

RS-232C connector

Cable hooks

to AC outlet

Ground

Video card

DVI-DVI or DVI-RGB cable

To USB

port

Rear Panel of your computer

To serial port

UM-0251/CintiqAP.pm65 01.7.31, 9:27 PM6

≈Turn on the power switch of the Cintiq 15X. The power lamp will light green , and then turns orange.

∆Turn on your computer to start your operating system.

➇By looking at the Cintiq 15X display, configure the monitor settings for proper size and color resolution.

(The recommended resolution is 1024 x 768. Other settings may give unsatisfactory results.)

The color pallet and number of colors are as follows:

-High Color (16 bit), 65,536 color

-True Color (24 bit), 16,770,000 color approximate

The number of colors is constrained by the performance of your computer or graphics card. Refer to the

documentation of the manufacturer for details.

➈To install the Wacom tablet software, turn off your computer and connect the USB cable or serial data

cable.

Tablet Software Installation for Windows*and Macintosh

➀After connecting all cables of the Cintiq 15X, turn on the Cintiq 15X and your computer. Allow the operat-

ing system to fully load.

➁Insert the Wacom Tablet CD into the CD-ROM drive. The Wacom tablet software installer menu should

automatically display. If the menu does not display, double-click on the INSTALL icon (located on the CD).

Click on the INSTALL CINTIQ button and follow the prompts to install the driver software.

➂Windows: After the driver installation is complete, make sure you can use your UltraPen on the tablet dis-

play to move the screen cursor.

Macintosh: After the driver installation is complete, restart your Macintosh. You will be able to use your

UltraPen on the tablet display to move the screen cursor.

Be sure to read the READMEfile for late braking news.

If you have trouble in the Tablet software installation, refer to the TROUBLESHOOTING CHAPTER in the online HelP

in the Wacom Tablet CD. You can also open the online Help from the HELP menu from the WACOM TABLET

control pane.

Precede to CUSTOMIZING YOUR CINTIQ 15X – THE BASICS.

*Windows 95 and later

UM-0251/CintiqAP.pm65 01.7.31, 9:27 PM7

Customizing Your Cintiq 15X – The Basics

Opening the Wacom Tablet Control Panel

The Wacom Tablet Control Panel makes it easy to customize your Interactive Pen Display and UltraPen.

To open the control panel:

Windows: Click on the Windows Start button and choose Programs. From the Wacom Tablet group,

choose the Wacom Tablet option.

Macintosh: From the Apple menu, choose Control Panels and then Wacom Tablet.

When you open the control panel, an icon for the UltraPen is displayed in the Tool List and the appropriate

tabs are displayed. To customize the UltraPen, make your changes to the tab controls.

On Windows systems, be sure to click APPLY or OK to save your changes.

Note: Application-specific settings are for advanced users. Refer to the online Help for more information on

creating and using application-specific settings.

Displays applications with

customized settings.

Current selections are highlighted. Wedges emphasize the relationship

between tab settings and the selected tool and application.

Displays an icon

for the UltraPen.

The pull-down menus access a

variety of control panel

features.

For Windows only:

OK saves changes and closes

the control panel. Cancel

closes the control panel

without saving changes. Use

Apply to save changes without

closing the control panel.

Displays online Help for the

control panel.

Tabs display settings for the

selected application.

Resets the selected tab to its

factory default values

Returns a tab to its previously

saved or last applied settings.

Copies settings from one tool

or application to another.

Windows screen capture shown.

UM-0251/CintiqAP.pm65 01.7.31, 9:27 PM8

Calibrating the Tablet

You will need to calibrate the tablet in order to line up the screen cursor position with the position of the

UltraPen on the Interactive Pen Display. This is required to adjust for parallax caused by the clear plastic

overlay. After setting the tablet in its working position, follow the procedure below to calibrate the tablet.

➀From the Wacom Tablet

Control Panel, select the

CALIBRATION tab.

If you are working with

multiple monitors, select

the Monitor that corre-

sponds to the tablet’s LCD

display.

➁Click on the CALIBRATE...

button to display the moni-

tor calibration screen..

➂Hold the pen as you nor-

mally do, and use the pen

tip to click on the cross-

hairs in the upper-left cor-

ner.

Then click on the cross-

hairs that are displayed in

the lower-right corner.

(You will need to click Ap-

ply or OK for the changes

to take effect.)

NOTE: The calibration setting

applies to all applications

UM-0251/CintiqAP.pm65 01.7.31, 9:27 PM9

Andere Handbücher für CINTIQ 15X

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Wacom Grafiktablett Handbücher

Wacom

Wacom DTU-1631 Bedienungsanleitung

Wacom

Wacom DTU-1931 Fehlerbehebungshandbuch

Wacom

Wacom GRAPHIRE - WINDOWS Bedienungsanleitung

Wacom

Wacom Intuos Pro L Bedienungsanleitung

Wacom

Wacom DTF-720 - OTHER Bedienungsanleitung

Wacom

Wacom DTK-2100 - INSTALLATION AND Bedienungsanleitung

Wacom

Wacom INTUOS4 WIRELESS PTK-540WL Bedienungsanleitung

Wacom

Wacom Cintiq 21UX Bedienungsanleitung

Wacom

Wacom DTK-2241 Bedienungsanleitung

Wacom

Wacom DTF-720AB Bedienungsanleitung

Wacom

Wacom INTUOS CTL-480 Bedienungsanleitung

Wacom

Wacom BAMBOO Bedienungsanleitung

Wacom

Wacom DTU-1031AX Bedienungsanleitung

Wacom

Wacom PTH-451 Bedienungsanleitung

Wacom

Wacom PENPARTNER - ANNEXE 474 Bedienungsanleitung

Wacom

Wacom Cintiq 21UX Bedienungsanleitung

Wacom

Wacom DTU-2231 Bedienungsanleitung

Wacom

Wacom cintiq 13HD Bedienungsanleitung

Wacom

Wacom INTUOS - FOR WINDOWS Bedienungsanleitung

Wacom

Wacom PL-720 - Bedienungsanleitung

Wacom

Wacom Cintiq Companion DTH-W1300 Bedienungsanleitung

Wacom

Wacom CINTIQ21 Bedienungsanleitung

Wacom

Wacom INTUOS2 - WINDOWS Bedienungsanleitung

Wacom

Wacom PENPARTNER - USB Bedienungsanleitung

Beliebte Grafiktablett Handbücher anderer Marken

BandRich

BandRich WritFun W120 Bedienungsanleitung

Evolveo

Evolveo Grafico T8 Bedienungsanleitung

Kanvus

Kanvus Artist 127 Bedienungsanleitung

GAOMON

GAOMON PD156 PRO Installationsanleitung

Parblo

Parblo A610 Plus Bedienungsanleitung

Huion

Huion KD200 Bedienungsanleitung

Orbit Research

Orbit Research GRAPHITI Bedienungsanleitung

CSSN

CSSN SigniShell LCD 3x2 Bedienungsanleitung

GAOMON

GAOMON S630 Bedienungsanleitung

HP 9111A Bedienungsanleitung

Huion

Huion Kamvas Pro 13 Bedienungsanleitung

Huion

Huion KAMVAS Pro 16 4K Bedienungsanleitung

Genius

Genius 1812HR Handbuch

Huion

Huion Inspiroy 2 S Bedienungsanleitung

Huion

Huion KAMVAS GT-191 V2 Bedienungsanleitung

Bosto

Bosto 22HD Bedienungsanleitung

VisTablet

VisTablet Original 12" VT ( ) Merkblatt

Perrix

Perrix Peritab-301 Bedienungsanleitung