Warmup Portrait 4iE Montageanleitung

4iE Portrait

Installation & Operating Manual

(WiFi & Non-WiFi)

For technical help:

US: (888) 927-6333

CA: (888) 592-7687

warmup.com

warmup.ca

Contents

Pack Contents .......................................................... 3

Mounting/Positioning.................................................. 4

Wiring Connections .................................................... 5

Assembling the 4iE..................................................... 9

4iE Portrait Setup - WiFi Version

Getting Started......................................................... 10

Registration............................................................. 11

4iE Portrait Setup - Non-WiFi Version

Non-WiFi Initial Setup................................................. 13

Welcome ................................................................ 14

Programming............................................................ 15

Settings.................................................................. 19

Troubleshooting ........................................................ 20

Important Notices...................................................... 23

Technical Specications............................................... 25

Back PlateThermostat Face Floor Sensor

IMPORTANT INFORMATION: Installation should only be carried

out by a qualied and competent electrician and must conform

to local electrical code. Conduits are only required where it

is mandated by state or provincial code. Please refer to local

electrical code for compliant applications.

The 4iE and its power supply should be isolated from

the mains supply throughout the installation process.

Pack Contents

Mounting/Positioning

Loosen both screws to

the left of the 4iE and

remove the Back Plate.

Install square 2 3/4” deep

back box with a single

mud ring (also called

plaster ring) in your

preferred thermostat

location.

4iE Portrait

Step 1 - Install Back Plate

Before making any permanent xtures Warmup recommends

identifying your preferred location for the 4iE. It should be

located in an area with good ventilation. It should not be beside a

window/door, in direct sunlight or above another heat generating

device (e.g. radiator or TV).

For the WiFi enabled 4iE, ensure the distance from your router to

the 4iE is not too great. This will reduce the risk of signal strength

and interference issues.

Faceplate

Thermostat

Trim plate

Mount faceplate vertically

Deep double-gang box recommended

Drywall

Wiring Connections

4iE Portrait

Step 2 - Wiring Connections

!Isolate the thermostat from the mains supply

throughout the installation process

Heating Load connected to 4iE - Max. 15 Amps

N.B. Input voltage 120V (Hot/Neutral) or

240V (Hot/Hot). Device is dual

voltage capable.

L1-LOAD-L2

L1-LINE

12 3

EXT

FLOOR SENSOR

(NO POLARITY)

L1-LOAD-L2

HEATING

(MAX 3600W/

15 Amps)

L1-LINE-L2

POWER

SUPPLY

L2-LINE

HOT (120V)

SUPPLY WITHOUT GFCI

PROTECTION

NEUTRAL (120V) OR

HOT (240V)

Heater/s

Max 15A

L1-LINE

This is the most common connection

Wiring Connections

4iE Portrait

Step 2 - Wiring Connections

240V SUPPLY WITHOUT GFCI

PROTECTION

L2-LINE

Hot (240V)

L1-LINE

240V GFCI

PROTECTED

SUPPLY

240V

COIL SUPPLY

N.B. All heating loads connect to Relay-25

only, controlled by 4iE

L1-LOAD-L2

L1-LINE

12 3

EXT

FLOOR SENSOR

(NO POLARITY)

L1-LOAD-L2

HEATING

(MAX 3600W/

15 Amps)

L1-LINE-L2

POWER

SUPPLY

Hot (240V)

0 1

8642

Heater/s

Max 25A

Heating Load connected to Relay 25 - Max. 25 Amps

Wiring Connections

4iE Portrait

Step 2 - Wiring Connections

240V SUPPLY WITHOUT GFCI

PROTECTION

L2-LINE

Hot (240V)

L1-LINE

240V GFCI

PROTECTED SUPPLY

Hot (240V)

L1-LOAD-L2

L1-LINE

12 3

EXT

FLOOR SENSOR

(NO POLARITY)

L1-LOAD-L2

HEATING

(MAX 3600W/

15 Amps)

L1-LINE-L2

POWER

SUPPLY

0 1

8642

Heater/s

Max 25A

Heater/s

Max 15A

240V

COIL SUPPLY

N.B. Heating loads connect to Relay-25

and 4iE:

Relay-25 Max load 25A

4iE Max load 15A

Total Max load 40A

Heating Load connected to 4iE and Relay 25 - Max. 40 Amps

For Larger installations

Wiring Connections

4iE Portrait

Step 2 - Wiring Connections

Master/relay function: Used to control loads greater than 15A.

Heaters will be split across two 4iE’s, one being the master and

the other being the relay (slave). Only one oor sensor is required,

wired into terminals 1 & 2 of the Master 4iE.

Wiring Connections: Use low voltage electrical cables to link

terminals 2 & 3 of the Master and Relay.

Thermostat Setup: Settings > Adv. settings > Heater setting > Ext

output

NOTE: Set the relay 4iE to relay rst.

4iE Portrait

Step 3 - Reattach 4iE Face

Reattach the 4iE face to the

Back Plate and tighten both

screws to secure. You may

now restore power to the

thermostat and begin setup.

Assembling the 4iE

Getting Started

Depending on who has installed your 4iE, you will have one of

the following screens visible. If you have anything other than the

screens below, please press the standby button on the underside of

Thermostat Face.

Steps 4 to 6 are specic to the WiFi enabled version of the 4iE. For

setup of the Non-WiFi version of the 4iE see page 13.

Language

If you have this

screen present, the

Thermostat has not

been connected to a

WiFi network.

Please follow the

on-screen

instructions to

connect it to WiFi.

No WiFi

If you have this

screen present, the

Thermostat must

be connected to a

WiFi network.

> Settings

> Network

4iE Portrait (WiFi Version)

Step 4 - Getting Started

No Server

If you have this

screen present, the

Thermostat is

connected to a WiFi

network and you

can continue to

device registration.

Registration can be

completed via the

MyHeating App or

by visiting

my.warmup.com.

back accept

Language

english

71 un�l 11:30

air

10:48.

69 ﬂoor

tue 5 jul

71 un�l 11:30

air

10:48.

69 ﬂoor

tue 5 jul

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Warmup Thermostat Handbücher

Warmup

Warmup WA-TSTAT-V Bedienungsanleitung

Warmup

Warmup OCC2 Bedienungsanleitung

Warmup

Warmup MTC-1991-WU Bedienungsanleitung

Warmup

Warmup WP-207-F Bedienungsanleitung

Warmup

Warmup DUALUDG-4999 Betriebsanleitung

Warmup

Warmup 3IE Bedienungsanleitung

Warmup

Warmup OCC2 Bedienungsanleitung

Warmup

Warmup 5iE Bedienungsanleitung

Warmup

Warmup 4iE WiFi Kurzanleitung

Warmup

Warmup WT01 Bedienungsanleitung

Warmup

Warmup UCCG Installationshandbuch

Warmup

Warmup 3IE Bedienungsanleitung

Warmup

Warmup 4iE WiFi Kurzanleitung

Warmup

Warmup 4iE WiFi Montageanleitung

Warmup

Warmup WA-TSTAT-V Bedienungsanleitung

Warmup

Warmup 3IE Bedienungsanleitung

Warmup

Warmup 3IE Bedienungsanleitung

Warmup

Warmup 5iE Kurzanleitung

Warmup

Warmup MTC-1991-WU Bedienungsanleitung

Warmup

Warmup Terra RSW Series Bedienungsanleitung

Warmup

Warmup konekt WIRELESS KW-STATH Bedienungsanleitung

Warmup

Warmup W3115DT AU Bedienungsanleitung

Warmup

Warmup WA-XSTAT Bedienungsanleitung

Warmup

Warmup + Kit Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung