Warmup Tempo ELT-01-XX-01 Bedienungsanleitung

User Guide

Pack Contents

Contents

Safety Information................................................................................................. 3

Step 1 - Installation................................................................................................ 3

Step 2 - Wiring Connections................................................................................. 4

Wiring Connections - Loads over 16 amps...........................................5

Step 3 - Thermostat Mounting............................................................................. 6

Welcome to the tempo thermostat ..................................................................... 7

Programming ......................................................................................................... 9

Installer settings...................................................................................................12

Troubleshooting ..................................................................................................14

Technical Specications ......................................................................................15

Warranty ...............................................................................................................16

x1 x1 x2 x1

Safety Information

Step 1 - Installation

The thermostat must be installed by a qualied electrician. It requires a

permanent 230 V AC supply from a 30mA RCD or RCBO protected circuit

in accordance with the current edition of the BS7671 Wiring Regulations.

Isolate the thermostat from the mains supply throughout the

installation process. Ensure that wires are fully inserted into the terminals

and secured, free strands should be trimmed, as they could cause a

short-circuit.

Install the thermostat in an area with good ventilation. It should not be

beside a window/door, in direct sunlight or above another heat generating

device (e.g. radiator or TV).

The supply to the thermostat must come from a ≤16A MCB, RCBO, or Fuse

to protect it and the heater from overloading.

For bathroom installations the thermostat MUST be mounted outside

of Zones 0, 1 and 2. If this is not possible then it must be installed in an

adjacent room, controlling the rooms using the oor sensor only.

The thermostat and its packaging are not toys; do not allow children

to play with them. Small components and packaging present a risk of

choking or suocation.

The thermostat is suitable for indoor use only. It must not be exposed

to moisture, vibrations, mechanical loads or temperatures outside of its

rated values.

For safety and licensing reasons (CE/UKCA), unauthorised change and/or

modication of the thermostat is not permitted.

Isolate the thermostat supply from

the mains supply.

Install a minimum 35 mm deep

electrical back box in your preferred

thermostat location. Pull wires

(heater, supply and oor sensor)

through back box and complete

terminal wiring.

Unclip the front housing from the

power module.

Release the front housing as

shown.

230 V AC:

50Hz Heaters. Max. 16A

(3,680W)

Sensor

Step 2 - Wiring Connections

WARNING!

The thermostat must be installed by a qualied electrician in accordance with

the current edition of the BS7671 Wiring Regulations.

NOTE: For loads above 10 A, the conductor wire gauge should be at least

2.5mm²

Electric Underoor Heating

Supply Live and Neutral

Floor heating Neutral and Live

Max. 16A (3680W)

Hydronic Underoor Heating

Supply Live and Neutral

Terminal 4 - Not Used

Terminal 5 - Switched Live to Wiring Centre

Central Heating

Supply Live and Neutral

Terminal 4 - Not Used

Terminal 5 - Switched Live to zone valve / boiler

For extra low voltage or volt-free systems a contactor must be used.

Connecting the tempo directly to extra low voltage or volt-free boilers may

cause damage to the boiler circuit.

Sensor Connection

7 & 8 Floor Sensor (No Polarity)

Fil Pilote

1 F.P Connect to Fil Pilote (F.P.) France Only

Step 2 - Wiring Connections - Loads over 16 amps

Warmup thermostats are rated for a maximum of 16 amps (3680 W). A

contactor must be used to switch loads exceeding 16 amps. Please see wiring

diagram below.

30 mA

≤16A

30 mA

≤16A

Snubber

L N PE

Step 3 - Thermostat Mounting

Insert xing screws through

mounting holes of the power

module and tighten.

Re-attach the front housing. You

can now power up the thermostat.

tempo

element

series

exclusivelyfrom

Locate your CR2032 3-Volt lithium

battery on the reverse of the

front housing. Remove the plastic

strip from under the battery. The

battery should always be installed

with positive side “+” facing

outwards.

Disconnect the power supply before replacing the battery. Only

use the same type of battery as listed in this manual.

Welcome to the tempo thermostat

Icons on tempo

1Rotary control

Rotate left/right to change increment

2Rotary button

3Program slider

4Mode slider

5Reset button

On reverse of the front housing

Standby

The thermostat is in standby mode and will not target any temperature. It is still

connected to mains electricity and your heating system is not isolated. Always isolate

from the mains before undertaking any maintenance.

Frost protect

The thermostat will not let the temperature fall below 5°C (41°F)

Manual mode

The thermostat will hold a xed temperature. Just turn the rotary control to change

the target temperature.

Program mode

In this position your thermostat will run the program you have set.

If you would like to temporarily adjust the temperature, just turn the rotary control.

This will set a temporary override and will hold a xed temperature until the next

scheduled program period.

* Periods 2 & 4 are the start times of the “Setback” temperature. The “Setback”

temperature is a lower energy ecient temperature when outside of a heating period.

If you do not require the heating on then set the setback temperature to 5°C.

Set time / day

Period 1 - Heating ON

Period 2 - Setback*

Period 3 - Heating ON

Period 4 - Setback*

Comfort temperature

Setback temperature

Run

The Tempo has been designed with simplicity in mind and is highly intuitive

in its programming. The sliders and simple rotary control make the setting of

the thermostat quick and easy.

Display icons

Current oor/Air temperature

Will also temporarily show set

temperature

Clock

Celsius/Fahrenheit Period 1 - Heating ON

Program mode Period 2 - Setback

Manual mode Period 3 - Heating ON

Frost protect Period 4 - Setback

Standby

Day of the week

Regulator mode

Floor sensor error

Air mode Displays when overheat

limit is reached

Floor mode

Fil Pilote

Heating indicator

No mains electricity available

Displays when COMFORT -1/

-2 is target temperature

When l pilote is activated

Battery needs to be replaced

When the thermostat displays both the manual and program

icon the thermostat is in a manual override and will hold a xed

temperature until the next scheduled program period.

In both manual and program modes, when setting a target

temperature or a temporary override, if the rotary control is not

moved for 3 seconds the temperature will ash once and revert

to displaying current air/oor temperature

Programming

How to set into Manual Mode

Setting into manual mode allows you to set a xed target temperature for

the thermostat to achieve. The thermostat will continue to maintain this

temperature until another operating mode or temperature is selected.

• Move the mode slider to the

manual mode icon “ ”.

• Ensure the program slider is in the

run position “

”.

• Move the mode slider to the

program mode icon “ ”.

• Move the program mode slider to

the set time / day icon “

”.

• Turn the rotary control clockwise/

anti-clockwise to increase or

decrease the target temperature

• To set the current time, turn

the rotary control clockwise /

anti-clockwise.

• To set the current day of the week,

press the rotary button and then

turn the rotary control.

How to set a program

Setting a program allows you to set comfort temperatures at set times

throughout the day. The tempo allows for 2 heating schedules to be set.

Days can programmed individually (7-day), all days the same (1-Day) or

weekdays as a block and weekends as a block (5-2), the choice is yours.

The tempo is defaulted to (5-2). This setting can be changed when the

program slider is on set time / day icon “

” and then pressing and

holding the rotary button for 5 seconds.

Moving the program slider to the next position saves the values you

have entered.

How to set a program

• Move the program slider to “1”.

• Turn the rotary control to set the

start time for “Period 1 - Heating

ON” for Mon-Fri.

• Move the program slider to “2”.

• Turn the rotary control to set the

start time for “Period 2 - Setback”

for Mon-Fri.

• Press the rotary button to

program “Period 1 - Heating ON”

for Sat-Sun.

• Turn the rotary control to set the

start time for “Period 1 - Heating

ON for Sat-Sun”.

• Press the rotary button to

program “Period 2 - Setback” for

Sat-Sun.

• Turn the rotary control to set the

start time for “Period 2 - Setback”

for Sat-Sun.

Move the slider to “3” and then “4”, repeating steps 3 - 6 above for

periods 3 & 4.

If you require one heating schedule then set the start times of periods

2 and 3 the same. Periods 1 and 4 will then be your Heating ON and

Setback times.

If you press and hold the rotary button for 3 seconds it will copy the

start time to the next day.

Inhaltsverzeichnis

Andere Warmup Thermostat Handbücher

Warmup

Warmup 4iE WiFi Kurzanleitung

Warmup

Warmup 4iE WiFi Montageanleitung

Warmup

Warmup WT01 Bedienungsanleitung

Warmup

Warmup 5iE Bedienungsanleitung

Warmup

Warmup W3115 Bedienungsanleitung

Warmup

Warmup OTN-1991-WA Bedienungsanleitung

Warmup

Warmup WA-XSTAT-V Bedienungsanleitung

Warmup

Warmup 3IE Bedienungsanleitung

Warmup

Warmup 3IE Bedienungsanleitung

Warmup

Warmup W3115DT AU Bedienungsanleitung

Warmup

Warmup WA-TSTAT-V Bedienungsanleitung

Warmup

Warmup Terra RSW Series Bedienungsanleitung

Warmup

Warmup TH115 A Bedienungsanleitung

Warmup

Warmup 3IE Bedienungsanleitung

Warmup

Warmup W3WT01 Bedienungsanleitung

Warmup

Warmup Terra Bedienungsanleitung

Warmup

Warmup UCCG Installationshandbuch

Warmup

Warmup tempo Bedienungsanleitung

Warmup

Warmup 3IE Bedienungsanleitung

Warmup

Warmup UDG Bedienungsanleitung

Warmup

Warmup Tempo Bedienungsanleitung

Warmup

Warmup WA-XSTAT Bedienungsanleitung

Warmup

Warmup 4iE WiFi Bedienungsanleitung

Warmup

Warmup 6iE Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Honeywell

Honeywell T6811 Bedienungsanleitung

Warmup tempo ELT-01-XX-01 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken