Waterax B2X Bedienungsanleitung

QUICK GUIDE

B2X-21

This Quick Guide shows the basic operation of the WATERAX B2X-21 2-stage mid-range pump.

• The WATERAX B2X-21 pairs a WATERAX 4-stage pump end with a Honda GX630 gasoline engine. For

instructions regarding the engine, as well as for oil and fuel recommendations, please refer to the engine

manufacturer’s manual.

• For detailed instructions on using and troubleshooting your pump, as well as full service and maintenance

instructions, refer to our website to download the B2X Owner’s Manual.

• For full specifications and performance curves, see the B2X-21 Data Sheet.

Warnings and Safety Precautions

This warning label appears on all WATERAXpumps to identify safety

hazards as follows:

READ YOUR ENGINE MANUAL!

Before proceeding further, locate and read the engine

manufacturer’s manual. It contains very important safety

information that MUST be read, understood and followed to

safeguard you and your equipment from harm, as well as for

the proper use and care of your engine. Use only fuel and

oil type recommended in the engine manufacturer’s manual.

Always check oil level in crankcase before use.

WEAR EAR AND EYE PROTECTION.

Always wear eye and ear protection when operating the

pump unit. Sound level of the unit: 92 dB(A).

GENERAL WARNINGS:

•Do not operate if mentally or physically fatigued.

•Inspect hoses and piping to avoid burst injuries.

•No modifications and/or alterations may be made to the

pump. Any such modifications void the pump warranty

and can endanger pump operators.

•Do not operate the pump above the maximum rated

pressure. Use only pipe, hose, and fittings rated at or

above the maximum pressure rating of the pump or

system design.

•Slowly close valves. Use slow close valves wherever

possible to safeguard operators and prevent damage

from water hammer.

•Dry weight of the unit: 169 lbs (will vary depending on

options).

QUICK GUIDE

READ THE PUMP OWNER’S MANUAL!

The improper use of this pump could result in serious injuries

as well as damage to the unit. Read the B2X Owner’s

Manualbefore using your B2X pump unit and follow the

safety instructions in this Quick Guide.

NEVER RUN THE ENGINE IN A CLOSED

OR CONFINED AREA.Exhaust gas contains

carbon monoxide which is poisonous to humans.

Avoid inhalation of exhaust gas.

REFUEL ENGINE WITH CARE. Gasoline is

extremely flammable, and gasoline vapor can

explode. Refuel in a well-ventilated area, with the

engine stopped.

NEVER TOUCH ANY EXHAUST SYSTEM

PARTS WHILE ENGINE IS RUNNING. Always

allow enough time, after stopping the unit, for proper

cooling of these parts and surrounding areas.

EQUIPMENT DAMAGE PREVENTION:

•Flush the pump with fresh water if the pump has been used to pump salty, brackish, high mineral content water,

water containing debris, or foam injected water. Check that debris is cleared before using the pump again.

Always draft water using a suction hose strainer.

•

Parts Identification

A. Priming port

B. Pump intake (suction)

C. Pump drain ports (not shown)

D. Quick release pump clamp

E. Pump discharge

F. Muffler

G. Starter key switch (not shown)

H. Choke (not shown)

I. Throttle

QUICK GUIDE

To operate the B2X-21 unit:

1. Fill fuel tank with recommended fuel grade and securely

replace cap. Check oil (see engine manual).

Suction/

Intake Port

Discharge Port

2. Connect the suction hose, using a universal hose coupling

wrench to tighten coupling firmly:

Drafting Mode: Connect the strainer or footvalve strainer to the

male end of the suction hose and then connect the female end

to the pump intake. NOTE: If desired, a suction hose with a

footvalve may be filled at this time to shorten pump priming.

Flooded Suction Mode: Connect female end of suction hose

to pump intake and connect male end to hydrant or other

supply.

a. Slowly open the pump inlet valves allowing the water into

the pump body.

b. Slowly open the discharge valves and priming valves to

allow for entrapped air in the piping to escape.

c. Once all the air has escaped, slowly close any discharge

and/or drain valves so that the unit may be started.

!!DO NOT allow the strainer to rest on bottom of lake or riverbed. Check strainer frequently to make sure that it is not

clogged with moss, leaves, etc.

!!DO NOT lift strainer from water while the pump is operating. Use a rope or other means to keep strainer at proper

height, approximately 1 foot (30 cm) below water surface. If strainer is too close to the water surface, it will draw air

and pump may lose prime.

3. Connect discharge hose, nozzles, etc., to pump, and tighten

firmly with coupling wrench.

4. Prime the pump.

Check that all drains, discharge valves, or any

auxiliary valves are closed before priming the pump.

Open the priming ball valve (located between the

pump and the primer).

Guzzler Priming: If equipped with a Guzzler primer,

follow the hand pump manufacturer’s operation

instructions. Pump until water is drawn into the

pump.

Electric Priming: See instructions for your electric

primer. Note that most electric primer motors are

intended to be used only a short duration (about 20

seconds). If pump fails to prime, see the B2X

Owner’s Manualfor troubleshooting tips.

Priming port

!! Close the priming valve after priming. Failure to close the priming valve could cause the pump to lose prime or

water to be pumped through the priming system.

QUICK GUIDE

5. Start the engine.

a. Close/engage choke, if engine is cold.

b. Increase throttle past the idle position.

c. Position the ignition switch to the ON position.

d. Turn the engine switch to START position until the engine starts. DO NOT hold for more than 5 seconds.

e. Open/disengage choke.

f. Allow the engine to warm up for at least 2 minutes before using full throttle.

6. Discharge water.

Once the pump is primed, and with the engine running, you can begin to discharge water.

a. If pressure does not build in the discharge hose, the pump has not been fully primed. The discharge valve

should be closed and the pump primed again.

b. Adjust the pump performance by throttling the engine up or down, or opening or closing discharge valves at

various positions, or any combination of the two.

!! DO NOT leave the pump running with all the discharge valves closed for more than one minute, or else the pump

may overheat and become damaged. To avoid this, a re-circulation line (if provided) should be opened or a discharge

line left slightly open to allow fresh water to continue to enter the pump.

QUICK GUIDE

To shut down and store the B2X-21 unit:

1. Shut down the pump.

a. Gradually reduce the engine speed.

b. Whenever the unit has been run at full throttle for most of the operation, allow the valves to remain slightly

open and run the engine at idle for approximately 5 minutes before shutting down the unit.

c. Turn off the engine.

d. Close off the hydrant/supply to the pump.

e. Open all valves to relieve any pressure left in the system.

2. Check and store the pump.

a. If the pump was last run with foam or water that is salty, brackish or high in mineral content, flush the pump

with fresh water for a minimum of 2 minutes or until the water is clear.

b. After the unit has cooled down, check all fluid levels and add as needed.

c. Completely drain the pump of all water.

d. Break down and store all equipment as outlined by the apparatus or department procedures.

e. Visually inspect the pump end. Clean any dirt or debris from the pump unit. If necessary, a mild soap and

water solution can be used. Note and report any performance irregularities or any abnormal mechanical

sounds.

f. Close all valves and plug all openings.

g. Follow any other product, component, apparatus, and departmental procedures and/or guidelines before

placing the unit in storage. Make sure all necessary tools, spares, and accessories are with the pump.

To operate the B2X-21 unit in cold weather:

The pump can be run in below freezing temperatures if certain precautions are taken to avoid the formation of

ice in the pump.

After priming the pump, the unit should be run at low speed for a short period of time to allow all components

to warm up before continuing with the remaining operating procedures.

Unless wrapped in a heater, drain the pump of all water if it is stopped for any length of time. The engine/drive

unit should be turned over a few revolutions to make sure all water has been removed from the pump. Drain

the pump priming line if a primer has been used.

After use, drain the pump, manifolds, and lines of all water. You can also pour some antifreeze into the pump

and circulate it through the pump and plumbing system.

Warranty, Service and Support

Product and service documentation such as tech notes, data sheets, manuals and information on the limited warranty

provided on products manufactured by WATERAX can be found on our Web site at: www.waterax.com

All information contained in this document including drawings is proprietary to

WATERAX and may not be copied, reproduced or used in whole or in part

without our prior written permission. The information in this document is

subject to change without notice. Model displayed with multiple options.

Weight and dimensions are approximated and may vary depending on options.

To help you stay #ReadyForWildres, we’ve made a few changes, placing

100% of our focus on manufacturing our core products, portable re pumps.

To do so, we’ve established a network of trusted supply and distribution

partners that can help us provide WATERAX pumps quickly in addition to

water-handling equipment and accessories.

For immediate assistance when it comes to pumps and water-handling

accessories, please contact your local dealer.

For genuine spare parts, visit our online store.

B2XTM is a trademark of Waterax.

WATERAX INC.

6635 Henri-Bourassa W.

Montreal, QC H4R 1E1

T 514 637-1818

F 514 637-3985

TF 1 855 616 616-1818

[email protected]

waterax.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Waterax Wasserpumpe Handbücher

Waterax

Waterax BB-4-21 Bedienungsanleitung

Waterax

Waterax Versax Bedienungsanleitung

Waterax

Waterax OT-4NX Bedienungsanleitung

Waterax

Waterax MINI-STRIKER MSTR-P Bedienungsanleitung

Waterax

Waterax B2X-18 Bedienungsanleitung

Waterax

Waterax BB-4 Series Bedienungsanleitung

Waterax

Waterax BB-4-D902 Bedienungsanleitung

Waterax

Waterax RANCHER Series Bedienungsanleitung

Waterax

Waterax BB-4-18/23 Bedienungsanleitung

Waterax

Waterax MARK-3 Bedienungsanleitung

Waterax

Waterax STRIKER-2/3 Bedienungsanleitung

Waterax

Waterax MARK-3 Bedienungsanleitung

Waterax

Waterax BB-4MD Bedienungsanleitung

Waterax

Waterax VERSAX-6/9 Bedienungsanleitung

Waterax

Waterax MARK-3 Bedienungsanleitung

Waterax

Waterax BB-4-18 Bedienungsanleitung

Waterax

Waterax Mini-striker series Bedienungsanleitung

Waterax

Waterax striker 2/3 Bedienungsanleitung

Waterax

Waterax STRIKER-II Series Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung