Waters Network Systems ProSwitch-Secure 1007 Bedienungsanleitung

WATERS NETWORK SYSTEMS™

OPERATING MANUAL

ProSwitch-Secure1007 Unmanaged Models

8-Port Enclosed Classroom and Workgroup Switches

CORPORATE HEADQUATERS MANUFACTURING/CUSTOMER SERVICE

5001 American Blvd. W., Suite 605 945 37th Avenue, NW

Bloomington, MN 55437 Rochester, MN 55901

Phone: 800.441.5319 Phone: 800.328.2275

Phone: 952.831.5603 Phone: 507.252.1951

Fax: 952.831.5605 Fax: 507.285.1952

Web site: http://www.watersnet.com

2ProSwitch 1007 – Unmanaged User’s Manual Page 2

TABLE OF CONTENTS

1.0 SPECIFICATIONS ............................................................................................................................. 3

2.0 PACKAGE CONTENTS - PROSWITCH-SECURE-1007 - UNMANAGED.................................... 4

2.1 PRODUCT DESCRIPTION................................................................................................................ 4

2.3 LOCATION OF THE PROSWITCH -SECURE-1007 ........................................................................ 4

3.0 CONNECTING THE PROSWITCH -SECURE 1007 TO YOUR NETWORK .................................... 4

4.0 MOUNTING THE PROSWITCH -SECURE 1007 .............................................................................. 5

5.0 POWERING THE PROSWITCH -SECURE 1007 ............................................................................. 5

6.0 STATUS OF LEDS ............................................................................................................................ 6

7.0 TROUBLESHOOTING....................................................................................................................... 6

7.1 BEFORE CALLING FOR ASSISTANCE .......................................................................................... 6

7.2 RETURN MATERIAL AUTHORIZATION (RMA) PROCEDURE...................................................... 7

7.3 SHIPPING AND PACKAGING INFORMATION ............................................................................... 7

8.0 WARRANTY ...................................................................................................................................... 8

2ProSwitch 1007 – Unmanaged User’s Manual Page 3

1.0 SPECIFICATIONS

OPERATIONAL CHARACTERISTICS:

MAC Address Table:

4K MAC

Switching Mode:

Store and forward

Performance:

Non-blocking switching architectures

Forwarding Rate:

10Mbps: 14,880 pps

100Mbps: 148,800 pps

Memory Buffer Size:

2MB

Auto-negotiation on TX ports

Broadcast storm filter function

NETWORK STANDARDS:

IEEE 802.3u: 100BASE-TX, 100BASE-FX Fast Ethernet

IEEE 802.3: 10BASE-T Ethernet

IEEE 802.3x Flow Control

EMI/SAFETY COMPLIANCE:

CE & FCC

FCC Class A, UL 1950, CSA C22.2 No. 950, EN60950, CE: EN55022 Class A, EN55024

FIBER PORT CHARACTERISTICS:

Multimode with SC, ST or MTRJ connectors

Speed: 100Base-FX

Wavelength: 1300nm

Maximum distance: 2km

Fiber size: 62.5/125, 50/125

Singlemode with SC connector

Speed: 100Base-FX

Wavelength: 1300nm

Maximum distance: 15/40/75km

Fiber size: 8/125, 9/125

NETWORK CABLE CONNECTORS:

10Base-T: CAT3, 4 or 5; up to 100M (328 feet)

100Base-TX: CAT5 or better; up to 100M (328 feet)

POWER SUPPLY:

Power Input Voltage: 100 to 240V; Internal

Power Input Frequency: 50 to 60Hz

Power Consumption: 2A, 15W max

OPERATING ENVIRONMENT:

Ambient: 32° to 104°F (0° to 40°C)

Storage: -13° to 158°F (-25° to 70°C)

Ambient relative humidity: 10% to 90% (non-condensing)

MECHANICAL:

Enclosure: Rugged high-strength sheet metal suitable for stand-alone, wall or tabletop mounting

Cooling Method: Convection cooled

PHYSICAL CHARACTERISTICS:

Dimensions: 16 x 11 x 2 (40.6 x 27.9 x 5.1cm)

Weight: 6.5LBS (2.95kg)

2ProSwitch 1007 – Unmanaged User’s Manual Page 4

2.0 Package Contents - ProSwitch-Secure-1007 - Unmanaged

Examine the shipping container for obvious damage prior to installing this product. Notify the carrier of any damage

that you believe occurred during shipment. Ensure that the items listed below are included.

The ProSwitch -Secure-1007 package contains the following:

8 port switch

AC power cord

2.1 Product Description

A switch can be used to overcome the hub-to-hub connectivity limitations as well as improve overall network

performance. Switches make intelligent decisions about where to send network traffic based on the destination

address of the packet. As a result, the switch can significantly reduce unnecessary traffic. The ProSwitch-Secure

1007 - unmanaged models provide 10/100Base-TX ports with an optional 100Base-FX port in a cost effective pocket

size package. The 10/100Base-TX ports auto negotiate speed and half/full duplex modes.

2.3 Location of the ProSwitch -Secure-1007

The ProSwitch 1007 can be installed quickly and easily. However, for an installation with minimum impact on the

existing network, please read the following information carefully. Installing the ProSwitch 1007 unmanaged switch

involves three steps:

1. Choosing a location

2. Supplying power

3. Connecting the switch

Consider the following criteria when selecting a location for the switch:

Avoid dusty locations

Avoid electromagnetic noisy areas, such as locations close to power transformers or radio transmitters

Avoid temperatures below 32° to 104°F (0° to 40°C)

Allow sufficient space for proper ventilation

Allow a clear view of the front panel LED indicators

Allow easy access to the front panel ports and the rear panel switches

The power outlet should be within six feet (1.8m) of the switch

3.0 Connecting the ProSwitch -Secure 1007 to Your Network

The1007 has been designed to support all standard Ethernet media types within a single switch unit. The various

media types supported along with the corresponding IEEE 802.3 and 802.3u standards and connector types are as

follows:

2ProSwitch 1007 – Unmanaged User’s Manual Page 5

Fiber:

Speed Media Type Max. Distance Connector Type Port Speed

Half/Full Duplex

100Base-FX Multimode fiber 2km SC, ST or MTRJ 100/200Mbps

100Base-FX Singlemode fiber 15, 40 or 75KM SC 100/200Mbps

Copper:

10Base-T CAT3, 4 or 5 100m (328ft) RJ45 10/20Mbps

100Base-TX CAT5 or 5E 100m (328ft) RJ45 100/200Mbps

NOTE: Since all switch ports are auto-sensing for both 10 and 100Mbps, it is recommended that high quality CAT5

cables or above (which work for both 10Mbps and 100Mbps) be used whenever possible in order to provide flexibility

in a mixed-speed network. Because the switch supports auto MDI/MDI-X detection, normal straight through cables

for both workstation connection and hub or switch connection can be used. All ports are auto MDI/MDI-X, so you can

use any of the ports to connect a port on another hub or switch with straight through or crossover cables.

4.0 Mounting the ProSwitch -Secure 1007

Table-Top or Shelf Mounting

The ProSwitch 1007 can be easily mounted on a table-top or any suitable horizontal surface. There are four rubber

feet provided for stability so finished surfaces won’t be scratched.

5.0 Powering the ProSwitch -Secure 1007

The ProSwitch 1007 switch is equipped with a universal power adapter that accepts AC input voltages from 100 to

240VAC and 50 to 60 Hz.

To supply power to your switch:

1. Plug the connector of the power cord into the power port on the rear panel of your switch.

2. Plug the power adapter into an AC wall outlet.

3. Set the power switch to ON and verify that the Power LED is lit. If it is not, check the following:

The power switch is in the ON position

The power cord is properly connected to the wall outlet and to the power connection on the switch.

The wall outlet is functional.

Note: Network cable segments can be connected or disconnected from the switch while the power is on, without

interrupting the operation of the switch.

2ProSwitch 1007 – Unmanaged User’s Manual Page 6

6.0 Status of LEDs

LED STATUS CONDITION

Power ON Switch is receiving power.

ON Port has established a valid link.

Link / Act

Flashing Data packets are being received or sent.

7.0 Troubleshooting

All Waters’ switching products are designed to provide reliability and consistently high performance in all network

environments. The installation of Waters’ ProSwitch -Secure 1007 switch is a straightforward procedure (See

Sections 3-5). Should problems develop during installation or operation, this section is intended to help locate,

identify and correct these types of problems. Please follow the suggestions listed below prior to contacting your

supplier. However, if you are unsure of the procedures described in this section or if the Waters’ ProSwitch -Secure

1007 switch is not performing as expected, do not attempt to repair the unit; instead contact your supplier for

assistance or contact Waters Network Systems’ Customer Support Center at 800.328.2275 or email

carolynl@watersnet.com.

7.1 Before Calling for Assistance

1. If difficulty is encountered when installing or operating the unit, refer back to the Installation Section of the

chapter of this manual. Also check to make sure that the various components of the network are inter-operable.

2. Check the cables and connectors to ensure that they have been properly connected and the cables/wires have

not been crimped or in some way impaired during installation. (About 90% of network downtime can be attributed

to wiring and connector problems.)

3. Make sure that an AC power cord is properly attached to the ProSwitch -Secure 1007.

4. Be certain that each AC power cord is plugged into a functioning electrical outlet. Use the PWR LEDs to verify

each unit is receiving power.

5. If the problem is isolated to a network device other than the Waters’ ProSwitch -Secure 1007 switch, it is

recommended that the problem device be replaced with a known good device. Verify whether or not the problem

is corrected. If not, go to next step. If the problem is corrected, the Waters’ ProSwitch -Secure 1007 switch and

its associated cables are functioning properly.

6. If the problem continues, contact Waters Network Systems Customer Service at 800.328.2275 or email

carolynl@watersnet.com for assistance.

When Calling for Assistance

Please be prepared to provide the following information.

1. A complete description of the problem, including the following points:

a. The nature and duration of the problem

2ProSwitch 1007 – Unmanaged User’s Manual Page 7

b. Situations when the problem occurs

c. The components involved in the problem

d. Any particular application that, when used, appears to create the problem

2. An accurate list of Waters Network Systems product model(s) involved. Include the date(s) that you purchased

the products from your supplier.

3. It is useful to include other network equipment models and related hardware, including personal computers,

workstations, terminals and printers; plus, the various network media types being used.

4. A record of changes that have been made to your network configuration prior to the occurrence of the problem.

Any changes to system administration procedures should all be noted in this record.

7.2 Return Material Authorization (RMA) Procedure

All returns for repair must be accompanied by a Return Material Authorization (RMA) number. To obtain an RMA

number, call Waters Network Systems Customer Service at 800.328.2275 during business hours of 8:00 am to 5:00

pm (CT) or email carolynl@watersnet.com. When calling, please have the following information readily available:

Name and phone number of your contact person

Name of your company/institution

Your shipping address

Product name

Packing List Number (or Sales Order Number)

Failure symptoms, including a full description of the problem

Waters Network Systems will carefully test and evaluate all returned products, will repair products that are under

warranty at no charge, and will return the warranty-repaired units to the sender with shipping charges prepaid (see

Warranty Information at the end of this manual for complete details). However, if Waters cannot duplicate the

problem or condition causing the return, the unit will be returned as: No Problem Found.

Waters Network Systems reserves the right to charge for the testing of non-defective units under warranty. Testing

and repair of product that is not under warranty will result in a customer (user) charge.

7.3 Shipping and Packaging Information

Should you need to ship the unit back to Waters Network Systems, please follow these instructions: Package the unit

carefully. It is recommended that you use the original container if available. Units should be wrapped in a "bubble-

wrap" plastic sheet or bag for shipping protection. (You may retain all connectors and this Installation Guide.)

CAUTION: Do not pack the unit in Styrofoam "popcorn" type packing material. This material may cause electro-static

shock damage to the unit.

Clearly mark the Return Material Authorization (RMA) number on the outside of the shipping container. Waters

Network Systems is not responsible for your return shipping charges.

Ship the package to:

Waters Network Systems

Attention: Customer Service

945 37th Avenue, NW

Rochester, MN 55901

2ProSwitch 1007 – Unmanaged User’s Manual Page 8

8.0 Warranty

Waters Network Systems’

Warranty Statement

Waters Network Systems’ products are warranted against defects in materials and workmanship. The warranty

period for each product will be provided upon request at the time of purchase. Unless otherwise stated, the warranty

period is for the useable life of the product.

In the event of a malfunction or other indication of product failure attributable directly to faulty materials and/or

workmanship, Waters Network Systems will, at its option, repair or replace the defective products or components at

no additional charge as set for herein. This limited warranty does not include service to repair damage resulting from

accident, disaster, misuse, neglect, lightning, acts of God, tampering or product modification.

Service under the warranty may be obtained by contacting Waters Network Systems and receiving a Return Material

Authorization (RMA) number from Waters Network Systems. Returned product accompanied with the issued RMA

number and prepaid shipping will be repaired or replaced by Waters Network Systems. Repaired or replaced

products will be returned at no cost to the original Buyer and shipped via the carrier and method of delivery chosen by

Waters Network Systems.

Specific warranty by product family is as follows:

ProSwitch-Secure: Limited Lifetime (see note)

ProSwitch-SecureAir+: Limited Lifetime

ProSwitch-Lite: 3 Years from date of manufacture (see note)

ProSwitch--Secure Xpress: Limited Lifetime

ProSwitch-Xtreme: Limited Lifetime (see note)

ProSwitch-FlexPort: Limited Lifetime

ProSwitch-FixPort: Limited Lifetime

ProSwitch-CS and CSX: 3 Years from date of manufacture (see note)

ProMedia Converters 3 Years from date of manufacture (see note)

Note: Warranty period for any and all external power supplies is one (1) year from date of purchase.

EXCEPT FOR THE EXPRESS WARRANTY SET FORTH ABOVE, WATERS NETWORK SYSTEMS GRANTS NO

OTHER WARRANTIES, EXPRESSED OR IMPLIED, BY STATUTE OR OTHERWISE, REGARDING THE

PRODUCTS, THEIR FITNESS FOR ANY PURPOSE, THEIR QUALITY, THEIR MERCHANTABILITY, OR

OTHERWISE.

WATERS NETWORK SYSTEMS’ LIABILITY UNDER THE WARRANTY SHALL BE LIMITED TO PRODUCT

REPAIR, OR REPLACEMENT OF THE BUYER’S PURCHASE PRICE. IN NO EVENT SHALL WATERS NETWORK

SYSTEMS BE LIABLE FOR THE COST OF PROCUREMENT OF SUBSTITUTE GOODS BY THE CUSTOMER OR

FOR ANY CONSEQENTIAL OR INCIDENTAL DAMAGES FOR BREACH OR WARRANTY.

Inhaltsverzeichnis

Andere Waters Network Systems Schalten Handbücher

Waters Network Systems

Waters Network Systems PS-2126M-POE Bedienungsanleitung

Waters Network Systems

Waters Network Systems PSX1008-TX Bedienungsanleitung

Waters Network Systems

Waters Network Systems MS1008-2G-4POE Bedienungsanleitung

Waters Network Systems

Waters Network Systems GSM 2124 Bedienungsanleitung

Waters Network Systems

Waters Network Systems GS1016 Bedienungsanleitung

Waters Network Systems

Waters Network Systems EN-FUTP-8 Bedienungsanleitung

Waters Network Systems

Waters Network Systems PSX1008-GTX Bedienungsanleitung

Waters Network Systems

Waters Network Systems ProSwitch FlexPort- 2600M Bedienungsanleitung

Waters Network Systems

Waters Network Systems GSM2109 Bedienungsanleitung

Waters Network Systems

Waters Network Systems ProSwitch 2800M Bedienungsanleitung

Waters Network Systems

Waters Network Systems ProSwitch Lite Bedienungsanleitung

Waters Network Systems

Waters Network Systems ProSwitch-Quad Series Bedienungsanleitung

Waters Network Systems

Waters Network Systems PSL1008-MSC Bedienungsanleitung

Waters Network Systems

Waters Network Systems GS1008 Bedienungsanleitung

Waters Network Systems

Waters Network Systems ProSwitch FlexPort- 2600M Bedienungsanleitung

Waters Network Systems

Waters Network Systems GSM2109-1009-8PoE Bedienungsanleitung

Waters Network Systems

Waters Network Systems GSM2108 Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung