Waters ACQUITY ELS Bedienungsanleitung

Inhaltsverzeichnis

Beliebte Sicherheitssensor Handbücher anderer Marken

THORLABS

THORLABS PDA10JT Bedienungsanleitung

Waeco

Waeco UV-DETECT Bedienungsanleitung

Intermatic

Intermatic IOS-DSIMF Bedienungsanleitung

urmet domus

urmet domus 1083 Bedienungsanleitung

Siemens

Siemens AZL66 Series Bedienungsanleitung

BTI

BTI Profiline Multi Finder Bedienungsanleitung

Challenger

Challenger SL01 Bedienungsanleitung

DMP Electronics

DMP Electronics 1122INT Bedienungsanleitung

Rielta

Rielta Ladoga MK-RK Bedienungsanleitung

Mirion Technologies

Mirion Technologies ACCURAD PRD Bedienungsanleitung

Bosch

Bosch DS835 Bedienungsanleitung

DBI SALA

DBI SALA EZ Stop Bedienerhandbuch

Lamptime

Lamptime ST05C Bedienungsanleitung

Ubiquiti

Ubiquiti MFI-MSC Bedienungsanleitung

Subsite

Subsite 910R Montageanleitung

Satel

Satel OPAL Pro Bedienungsanleitung

Aleph

Aleph XC-1XTEU Bedienungsanleitung

Pima

Pima LARIS QUAD Bedienungsanleitung

Quick Install Guide

Waters®ACQUITY ELS Detector

Serial Number:

Date Installed:

Installed By:

715001213, Rev. B 2 of 5

Connecting Your Detector

For detailed installation information and cautionary statements regarding this product, refer to the

following documents:

• ACQUITY Evaporative Light Sattering Detector Operator’s Guide (71500109303)

• Ethernet Instrument Getting Started Guide (71500074403)

• Installing System Leak Sensors (715001557)

•ACQUITY UPLC Leak Sensor Maintenance Instructions (71500082506). This document is an

addendum to the ACQUITY UPLC System Operator’s Guide.

Electrical Connections

A. Connect any required event or signal cables.

B. Connect an Ethernet cable from the detector to the

system LAN switch or to the

network card on the acquisition computer.

C. Connect the power cable to a grounded receptacle.

BA

Signal Out +

Signal Out –

Ground

Auxillliary Out +

Auxillliary Out –

Stop Flow +

Stop Flow -

Ground

Switch 2 +

Switch 2 -

1

2

3

4

5

6

7

8

9

10

Inject Start +

Inject Start –

Ground

Lamp On/Off +

Lamp On/Off –

Chart Mark +

Chart Mark –

Ground

Auto Zero +

Auto Zero –

A

B

Ethernet

Cable

441000372

or

441000456

C

Fuse - WAT163-16 (if equipped)

Range: 110 Vac to 240 Vac

Gas Connection

Figure 1 - ACQUITY ELS Rear Electrical and Gas Connections

110 V - WAT097194

220 V - WAT097410

Gas Exhaust

715001213, Rev. B 3 of 5

A. Remove the nebulizer and fill the U-tube with mobile phase.

B. Slide the nebulizer into place with the air coupler at 12 o’clock to align the pins

and turn it 90 degrees clockwise.

C. Connect the column’s outlet using PEEK tubing (P/N 430001562) to the

nebulizer’s inlet port. If connecting from a UV detector, use PEEK tubing P/N

430001565.

D. Connect the gas input to the nebulizer’s gas inlet port.

E. Connect the drip tray tubing to the waste management system.

E

F

B

CD

Push in, then

turn right 90

degrees.

Install tubing.

Nebulizer Connections

A

Figure 2 - Filling U-Tube Figure 3 - Nebulizer Connections

Figure 4 - Plumbing and Leak Sensor Installed

715001213, Rev. B 4 of 5

Gas Exhaust on

Chassis Rear Gas Input on

Chassis Rear

To Exhaust

Hood

Figure 5 - Proper Gas Venting

Gas Connections

715001213, Rev. B 5 of 5

Power Up

The quality management system of

Waters' chromatography applications

software design and manufacturing

facility, Milford, Massachusetts, complies

with the International Standard ISO

9001 Quality Management and Quality

Assurance Standards. Waters' quality

management system is periodically

audited by the registering body to ensure

compliance.

Waters Corporation

34 Maple Street

Milford, MA 01757

508 478-2000

http://www.waters.com

Waters is a registered trademark of Waters Corporation

The Science of What’s Possible is a trademark of Waters

Corporation

Printed in U.S.A. September, 2007

715001213, Rev. B

If you have any questions regarding this installation, call your local Waters office. In the U.S. call 1-800-252-HPLC.

The detector is operational when the two LEDs on the front panel are green.

The System Status LED on the ACQUITY ELSD Console interface turns green and a trace is visible,

also indicating a successful startup.

System

Status

LED

Power Switch

Green LEDs

Figure 5 - Indication of Successful Startup on ACQUITY ELSD Console