Wayne-Dalton 3790 Bedienungsanleitung

Tools Needed:

Step Ladder

Phillips Screw Driver

Select a grounding type receptacle on either

the ceiling or wall. If one is not available, have

one installed by a qualified electrician.

IMPORTANT! DOOR MUST CLEAR LIGHT

FIXTURE WHEN THE DOOR IS IN THE OPEN

POSITION.

Identify a mounting location for the light fixture

that’s in close proximity to the receptacle, and

within reaching distance of the power cord.

Fasten the mounting bracket to a stud, in the

desired location using (2) #10 x 1-1/2” deep

thread screws. Align the two metal tabs on the

mounting bracket. Hold the light fixture flush

against the mounting bracket using (1) #8 x

0.375” screw as shown. Place the hole plug

into the screw hole in the light fixture.

NOTE: For temperature protection, the hole

plug must be in place prior to using the light

fixture.

TO AVOID ELECTRICAL SHOCK/FIRE,

DO NOT CHANGE THE POWER CORD

PLUG IN ANY WAY.

IMPORTANT! THE POWER CORD HAS A

GROUNDING TYPE PLUG WITH A THIRD

(GROUNDIING) PIN. THIS PLUG WILL ONLY FIT

INTO A GROUNDING TYPE OUTLET. IF THE

PLUG DOES NOT FIT INTO YOUR OUTLET,

CONTACT A QUALIFIED ELECTRICIAN TO

INSTALL THE PROPER GROUNDING TYPE

OUTLET. DO NOT ALTER THE PLUG IN ANY

WAY.

Plug the female end of the power cord into the

inlet connect of the light fixture. Now, plug the

other end of the power cord into the nearest

grounding type receptacle. As soon as power is

applied to the light fixture it should blink one

time. Use cable clips and #6 x 7/8” wood

screws to secure the power cord.

Z-WAVE LIGHT KIT INSTALLATION

FOR TORSION I-DRIVE

Installation Instructions P.O. Box 67 Mt. Hope, OH 44660

GARAGE DOORS & OPENERS

www.wayne-dalton.com

This insert is to be used in conjunction with the main installaton instructions and owner’s manual.

This insert is for Z-Wave I-Drive TorqueMaster®Pro Operator Only!

WARNING

Mounting Bracket

(P/N 293294)

#8 x 0.375”

Phillips Pan Head

Screw

Hole Plug-Snap In

(P/N 311122-6)

(ITW Fastex 354-310102-00-2099)

(2) #10 x 1-1/2” Deep Thread

Screws (P/N 279995)

Light Fixture

Wire Clips

#6 x 7/8” Wood

Screws

Plug into nearest outlet

Screw a 15W Type-A bulb or 19W Compact

Fluorescent (maximum) light bulb into light

socket and snap diffuser into light fixture.

NOTE: When assembling diffuser, make sure

all three snap tabs are aligned and fully

snapped into the three mating slots of the

light fixture.

Turn receptacle power back on at fuse/breaker

box. The light should blink one time when the

power is turned back on.

IMPORTANT: FOR REPLACEMENT BULBS USE

ONLY 19W MAX COMPACT FLUORESCENT

BULBS OR USE ONLY 15W MAX TYPE-A

BULBS FOR THE LIGHT.

Top portion of Light

Fixture

Inlet Connector

Pg 1

Programming the Z-Wave Light Kit to the i-Drive TorqueMaster

Pro.

If your Z-Wave Light Kit is included with the opener, it should

already be programmed to the opener. Otherwise, follow the

instructions below.

IMPORTANT: ERASE ANY EXISTING PROGRAMMING ON

Z-WAVE LIGHT KIT

1. Press and hold the DELETE button on the unplugged

Wireless Gateway until the 3 LEDs turn on, then let go of the

button.

2. Press the red button on the Z-Wave Light Kit and

observe the LEDs on the Wireless Gateway flash. All network

programming, if any, has now been deleted from the Z-Wave

Light Kit. Press the red button again to turn off the light. If the

button is held in, the Z-Wave Light Kit may flash its light on

and off repeatedly. This is okay.

PROGRAM Z-WAVE LIGHT KIT TO PRIMARY CONTROLLER

1. Insure the Z-Wave Light Kit light is off.

2. Press the Scene 1 button on the Wireless Gateway and

observe that the LED lights up. Continue holding the button

down until the LED turns off and the turns back on again.

3. While the Scene 1 button is still being pressed, press

the red button on the Z-Wave Light Kit, while observing the

LED for Scene 1. If the LED flashes, the Z-Wave Light Kit has

been successfully programmed to Scene 1 of the Wireless

Gateway.

4. Release the button on the Wireless Gateway.

5. Note: If the programming was unsuccessful, try moving

the Wireless Gateway closer to the Z-Wave Light Kit or change

orientation.

COPY PRIMARY CONTROLLER PROGRAM TO THE Z-WAVE

OPERATOR

1. Press and hold the Learn button on the I-Drive

TorqueMaster®Pro until all 4 LEDs are blinking. Release the

button.

2. With the Wireless Gateway in close proximity to the

I-Drive TorqueMaster®Pro, press and hold the copy button on

the Wireless Gateway until all 3 LEDs are flashing.

3. Observe the 4 LEDs on the I-Drive TorqueMaster®Pro. If

programming is successful, the LEDs will begin blinking at a

different rate, and then turn off. If not, then you may have to

move the Wireless Gateway closer or change the orientation.

4. The Z-Wave Light Kit will now come on when the

operator is engaged. The light will automatically shut off after

approximately 5 minutes. Additionally, by default, Scene 3 will

turn off Scene 1. Therefore, the light can be turned off by

pressing Scene 3 on the Wireless Gateway.

Programming the Z-Wave Light Kit

Scene 1

Scene 2

Scene 3

Delete

Copy

Program Button

Light Button

LED

Light Fixture

Diffuser

Light Bulb

(Not Included)

Power Socket

Snap Tabs

(3) Mating Slots

Light Socket

Caution!Risk of Fire

Use Only 15W Max.

TYPE- A

Caution!Risk of Fire

Use Only 19W Max.

COMPACT

FLUORESCENT

Pg 2

Wireless Gateway

FCC and IC Statement

FCC Regulatory Information:

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause

harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired

operation.

IC Regulatory Information:

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any

interference, including interference that may cause undesired operation of the device.

NOTE: This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with these instructions, may cause

harmful interference to radio communication; however, there is no guarantee that interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or television reception, which can be determined by turning equipment off and

on, user is encouraged to try to correct interference by one or more of the following measures: Reorient or relocate receiving antenna.

Increase separation between equipment and receiver. Connect equipment into an outlet on a circuit different from that which receiver is

connected. Consult your dealer or/and experienced radio/television technician for help.

WARNING: Changes or modifications to this unit not expressly approved by party responsible for compliance could void user’s authority

to operate this equipment.

Patent Information

Models:

3790/3790-Z

Made under the following US patents and methods D413,579; D466,141; D472,568; D472,910; D473,573; D473,574;

D474,215; D505,393; D517,580; CA 2,348,784; 5,929,580; 6,078,249; 6,145,570; 6,164,014; 6,253,824; 6,263,947;

6,325,134; 6,326,751; 6,326,754; 6,401,792; 6,561,255; 6,561,256; 6,568,454; 6,588,156; 6,605,910; 6,667,591; 6,739,372;

6,845,804; 6,851,465; 6,873,127; 6,880,609; 6,903,650; 7,053,571; 7,061,197; 7,075,256; 7,109,677; 7,123,128; 7,143,804;

7,173,389; 7,173,514; 7,173,516; 7,183,732; 7,190,266; 7,193,502; 7,207,142; 7,211,975; 7,246,647; 7,280,031; 7,327,107;

7,327,108; 7,327,249; 7,358,480; 7,367,160; 7,375,484; 7,375,612; 7,376,401;7,397,342. Other US and Foreign Patents

pending.

Dieses Handbuch passt für folgende Modelle

Andere Wayne-Dalton Garagentoröffner Handbücher

Wayne-Dalton

Wayne-Dalton 8000 Series Kurzanleitung

Wayne-Dalton

Wayne-Dalton 105/110 Kurzanleitung

Wayne-Dalton

Wayne-Dalton TORQUEMASTER 6100 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 8000 Series Kurzanleitung

Wayne-Dalton

Wayne-Dalton Flush 42 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton TorqueMaster Plus 6100 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton DS-350 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 8500 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 8700 Kurzanleitung

Wayne-Dalton

Wayne-Dalton Windload Post 9100 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 9100 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton Optimal Installationsanleitung

Wayne-Dalton

Wayne-Dalton Torsion 7100 Series Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 3018 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 9800 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 9800 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 9100 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 9100 Kurzanleitung

Wayne-Dalton

Wayne-Dalton 8000 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton 9100 Technisches Dokument

Wayne-Dalton

Wayne-Dalton 9600 Kurzanleitung

Wayne-Dalton

Wayne-Dalton Torquemaster Plus 8000 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton TORQUEMASTER 6100 Bedienungsanleitung

Wayne-Dalton

Wayne-Dalton ThermoMark 5150 Bedienungsanleitung

Beliebte Garagentoröffner Handbücher anderer Marken

Dorma

Dorma ES 90 Bedienungsanleitung

Garaga

Garaga SECURITY+ 3265GCM 1HP Bedienungsanleitung

Chamberlain

Chamberlain Whisper Drive SECURITY+ WD822K Series Bedienungsanleitung

Chase Doors

Chase Doors DuraShield Bedienungsanleitung

CSI

CSI Classic Bedienungsanleitung

HATO

HATO 120 Bedienungsanleitung

Chamberlain

Chamberlain Elite 3575S Bedienungsanleitung

Richmond

Richmond GTR156 Bedienungsanleitung

Raynor

Raynor 1280RGD Bedienungsanleitung

CAME

CAME F4000 Series Bedienungsanleitung

B&D

B&D Controll-A-Door 5 Bedienungsanleitung

BFT

BFT PRV AA SL Bedienungsanleitung

Craftsman

Craftsman 139.53924 Bedienungsanleitung

Chamberlain

Chamberlain MyQ 940ESTD Bedienungsanleitung

Automatic Technology

Automatic Technology GDO-9V1 SecuraLift Bedienungsanleitung

Westfalia

Westfalia 19 36 07 Bedienungsanleitung

Chamberlain

Chamberlain HD520EVP Bedienungsanleitung

Cardin

Cardin BL Series Bedienungsanleitung