WeatherBug HD MotionCam Bedienungsanleitung
Release 1, Version 1.0
High Definition
Motion Camera
System Installation,
Operation, and
Maintenance Manual
February 2011
HD MotionCam Installation Manual
Release 1, Version 1.0 -2- February 2011
Copyright
Copyright 2011, by AWS Convergence Technologies, Inc.
All Rights Reserved.
Manual Copyright, 2011, by AWS Convergence Technologies, Inc.
All Rights Reserved.
Information in this document is subject to change without notice and does not represent a
commitment on the part of AWS Convergence Technologies, Inc.
FCC Compliance
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy, and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his, or her, own expense.
HD MotionCam Installation Manual
Release 1, Version 1.0 -3- February 2011
Disclaimer
The procedures, methods, and hardware described in this manual are intended to provide
general guidelines and instructions for installing the WeatherBug High Definition Motion
Camera (HD MotionCam) system. Each installation site is unique and each site may
require special considerations that are beyond the scope of this manual. Any questions
not covered within this manual should be directed to WeatherBug Weather Station
All procedures, methods, and hardware used to install a WeatherBug HD MotionCam
system must conform to all applicable building codes (national, state, and local).
Installation subcontractors are responsible for complying with all applicable codes.
Buyer and/or installer provided hardware must be equivalent or better (according to
industry standards) than that specified in the WeatherBug Installation Manual.
The buyer/installer is responsible for any damage caused by installation of the
WeatherBug HD MotionCam.
THINK SAFETY FIRST!
Warranty. The Seller warrants the hardware purchased by the Buyer against defects in
workmanship and materials for a period of one (1) year from date of delivery under this
contract. The Seller shall, at its sole option, either repair or replace defective items.
Buyer is responsible to return of defective items to Seller by means specified by the
Seller. The Buyer shall bear all shipping expenses. Packing of defective items for
return is responsibility of Buyer. Damage due to natural causes (storms, lightning,
flying debris, etc.) is not covered by this warranty. Damage resulting from Buyer
negligence or mishandling of hardware and software is not covered by this warranty.
HD MotionCam Installation Manual
Release 1, Version 1.0 -4- February 2011
Table of Contents
Copyright ............................................................................................................................ 2
Disclaimer........................................................................................................................... 3
Table of Contents................................................................................................................ 4
Thank You!.......................................................................................................................... 5
Plan Ahead.......................................................................................................................... 5
Safety! ................................................................................................................................. 6
Getting Started.................................................................................................................... 7
Camera System Parts ...................................................................................................... 7
Tools Needed.................................................................................................................. 9
Site Evaluation.............................................................................................................. 10
Installation........................................................................................................................ 11
Indoor Preliminary Setup.............................................................................................. 11
Viewing Live Video and Captured Images................................................................... 13
Live Video ................................................................................................................. 13
Captured Images....................................................................................................... 16
Routing the Cable ......................................................................................................... 17
Outdoor Installation...................................................................................................... 18
Indoor connections........................................................................................................ 21
Setting a Static IP Address for the HD MotionCam......................................................... 22
Troubleshooting................................................................................................................ 25
Maintenance...................................................................................................................... 26
Additional Information...................................................................................................... 27
Specifications.................................................................................................................... 28
HD MotionCam Installation Manual
Release 1, Version 1.0 -5- February 2011
Thank You!
Thank you and congratulations on acquiring the WeatherBug HD MotionCam system.
The WeatherBug HD MotionCam captures images of local weather conditions with the
advantage of a much higher resolution and the flexibility of changing viewpoints as often
as desired. The quality of the images from the WeatherBug HD MotionCam is sure to
enhance your weather system.
By installing and operating the entire WeatherBug system, you become an essential part
of the WeatherBug program, an integrated network of weather stations comprising the
largest weather monitoring system in the world.
You can monitor a high-quality, live image from the camera using a computer connected
to a Local Area Network (LAN). The frame rate is 30 frames per second (FPS).
Captured images are also available through the internet at www.weatherbug.com.
Plan Ahead
Read this entire manual before beginning installation. The WeatherBug HD MotionCam
installation can be straightforward and easy to complete if all steps are followed closely.
In order to ensure the most efficient installation possible, you MUST follow the steps
in “Indoor Preliminary Setup” BEFORE installing ANY equipment outdoors.
The most important aspect of preparation is safety. Installation of the HD
MotionCam requires working with electrical cable, drilling through walls or other dense
support structures, standing on ladders, and possibly, walking on roofs. Please carefully
read the following section on “Safety.”
Please pay close attention to the section on “Site Evaluation.” A complete site evaluation
determines proper placement of the camera and will prevent the need to have to re-mount
the camera and re-route the cables.
All additional parts needed (such as ladders, drills, bits, etc.) should be assembled and
inspected before beginning installation. WeatherBug cannot accept responsibility for
damage caused by these tools so all safety precautions should be adhered to. This would
include the use of leather gloves and goggles when appropriate.
If there are any questions, doubts, or discrepancies, call WeatherBug Weather Station
HD MotionCam Installation Manual
Release 1, Version 1.0 -6- February 2011
Safety!
Only qualified personnel should install the HD MotionCam.
While installation of the HD MotionCam is not particularly difficult, it does usually
require installation near the rooftop and working with electrical wiring, which presents
some amount of risk.
To limit risk to self and property, this manual should be thoroughly read and understood
before beginning installation. Adhere to all warnings on the unit and in the operating
instructions.
Installation must conform to national, state, and local building code requirements with the
most stringent guidelines being adhered to.
The HD MotionCam should only be installed by someone comfortable with being on a
high ladder or rooftop and who is authorized by the site to perform the installation. Roof
and ladder safety is crucial!
Allow only qualified Electricians to make electrical connections. Take all reasonable
safety precautions – double checking a power cable connection could save a life.
Stay as far away from other electrical wiring as possible. Never allow the camera
housing, the cabling, a drill bit, or any other item to contact electrical wires or
conduit. Injury or death could result.
A qualified installer will need to securely mount the unit to a supporting structure capable
of sustaining the weight of the unit (approximately 16 pounds) by using appropriate tools
and hardware. Failure to properly secure the HD MotionCam could result in the unit
separating from the support structure and falling. This would not only damage the
camera, but could injure anyone standing nearby.
If needed, WeatherBug may be able to recommend professional installers and an estimate
of the cost. If this is desired, please call WeatherBug Weather Station Technical Support
HD MotionCam Installation Manual
Release 1, Version 1.0 -7- February 2011
Getting Started
Camera System Parts
Item Part Number
HD MotionCam in Housing 5500
Camera Support with Clamp for Mounting Arm Included in 5500
Connector for Camera and Mounting Arm Included in 5500
3 Rubber Plugs Included in 5500
4 Spare Screws with Washers Included in 5500
Enclosure for Top of Camera Housing Included in 5500
MotionCam Mounting Arm 8570
100 ft HD MotionCam Power Cable 5512
200 ft Cat 6 Ethernet Cable 8525
HD MotionCam Power Supply 5510
Network Surge Suppressor 8550
5 ft Cat 5 Network Ethernet Cable 5452
Install Sealant 1166
Cable Ties 1168
5 mm Allen Wrench xxxx
Please carefully unpack, set out, and identify each part and
inspect for damage. If any damage is noticed, please call
WeatherBug Weather Station Technical Support at 800-624-
HD MotionCam Installation Manual
Release 1, Version 1.0 -8- February 2011
Outdoor Components
HD MotionCam in Housing
Camera Support with Clamp, Connector for
Camera and Mounting Arm, 3 Rubber Plugs,
Enclosure for Top of Housing, and Spare
Screws
Mounting Arm
Install Sealant
Cable Ties
Indoor Components
100 ft Power Cable
200 ft Ethernet Cable
Power Supply
Network Surge Suppressor
5 ft Ethernet Cable
HD MotionCam Installation Manual
Release 1, Version 1.0 -9- February 2011
Tools Needed
(Not supplied by WeatherBug)
•Wire cutters and pliers
•#2 Phillips screwdriver
•10 mm wrench
•Heavy-duty drill with bits sized up to 1-1/4” – bits must be appropriate for
material being drilled into (masonry, wood, metal, etc.) and must be long enough
to penetrate the support walling from exterior to interior (possibly as much as 10”
or more).
•Socket drivers, designed to be used with a drill, of the size(s) needed to fit the
screws intended for use in mounting the HD MotionCam.
•Fish Tape to pull cable through wall
•Electrical Tape to tape the ends of cables for protection and to hold connectors
and cables together.
•Bolts/Screws needed to attach the mounting arm to the wall will vary according to
several factors. Both the composition of the mounting surface and the weight of
the unit (approximately 16 pounds) must be taken into account.
•An adjustable ladder
HD MotionCam Installation Manual
Release 1, Version 1.0 -10- February 2011
Note: Keep in mind that the unit comes with 100 feet of power cable that must
reach from the camera to a power outlet. The unit also comes with 200 feet of
Ethernet cable that must reach from the camera to the network connection. Any
cable routed on the building structure exterior must be secured and routed in a
conduit. THE MAXIMUM LENGTH OF POWER CABLE IS 100 FT.
Site Evaluation
All sites will have certain building restrictions. To get the most out of the camera, a
location needs to be chosen that will present the least restrictions.
The sky, sun, and clouds are important elements in the captured images. A “perfect”
picture includes about 50% sky and about 50% earth.
Remember that the camera will be operating throughout the year. A good view in the late
fall or winter may be obstructed by tree growth in the spring and summer.
Spend time looking at the lighting and shading based on the time of day, types of
weather, and time of year. It is best to center the camera facing toward the prevailing
winds – generally westerly in the United States. If you invest the time now in site
evaluation, your efforts are sure to pay off in the end.
The camera must also be securely mounted to avoid distortion of the camera images. The
mounting arm must be wall mounted for optimal stabilization. The camera should be
mounted high enough so that there is a clear view of the horizon. The unit should be
mounted so that it is easily accessible. This will aid in any maintenance or adjustments
that may have to be made. Once you have chosen the direction you want the camera to
face, it should be mounted on the outermost wall in that direction. This will keep any
roofs and unnecessary structures out of your camera view.
Select and verify a route to run the cables from the camera to the interior of the building.
Inhaltsverzeichnis
Andere WeatherBug Sicherheitskamera Handbücher
