WEIHONG NcEditor V12 Bedienungsanleitung
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
NcEditor V12 Laser Cutting CNC System
Manufacturer Manual
Version: 2019.3 1st Version
Author: Document Department
Weihong Corporation, All Rights Reserved
1CNC System Installation...............................................................................................................2
1.1 Install Hardware ............................................................................................................2
1.2 Install Software...............................................................................................................6
1.3 Install Driver....................................................................................................................9
1.4 Install a Camera........................................................................................................... 12
2Interface Overview...................................................................................................................... 14
2.1 Toolbar............................................................................................................................ 16
2.2 Drawing Window........................................................................................................ 17
2.3 Running Information Bar......................................................................................... 18
2.4 Window Display Buttons ......................................................................................... 19
2.5 Machine Control Area................................................................................................ 19
2.6 Status Bar....................................................................................................................... 25
2.7 Drawing Toolbar ......................................................................................................... 26
2.8 3D View Area ................................................................................................................ 26
3Machine Tool Commissioning................................................................................................. 28
3.1 Modify Port Polarity................................................................................................... 28
3.2 Set Drive Parameters................................................................................................. 28
3.3 Adjust Pulse Equivalent and Electronic Gear Ratio....................................... 50
3.4 Set Speed Parameters................................................................................................ 52
3.5 Adjust the Axis Direction ......................................................................................... 52
3.6 Set the Workbench Stroke....................................................................................... 53
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
3.7 Compensate Lead Screw Errors............................................................................ 53
3.8 Set Parameters of Air Pressure and Laser Device.......................................... 56
3.9 Check Machine Tool Setting.................................................................................... 58
4Follow-up........................................................................................................................................ 61
4.1 Interface Overview..................................................................................................... 61
4.2 Commissioning Steps ................................................................................................ 69
4.3 List of Parameters....................................................................................................... 73
4.4 FAQs................................................................................................................................. 80
5List of System Parameters........................................................................................................ 84
5.1 Basic Parameters ........................................................................................................ 84
5.2 Speed and Accuracy Parameters........................................................................... 96
5.3 External Device Parameters .................................................................................104
5.4 Advanced Function Parameters..........................................................................109
6Electrical Wiring Diagram......................................................................................................113
6.1 Mounting Dimension...............................................................................................113
6.2 Wiring Diagram of Terminal Board ...................................................................116
6.3 Wiring Diagram of Laser Device .........................................................................124
6.4 Wiring Diagram of Drive........................................................................................131
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
1/ 144
NcEditor V12 Laser Cutting CNC System is independently developed by Weihong
Electronic Technology Co., Ltd., with copyright reserved.
This manual is intended for manufacturers of machine tools.
It mainly includes the following:
•CNC System Installation
•Interface Overview
•Machine Tool Commissioning
•Follow-up
•List of System Parameters
•Electrical Wiring Diagram
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
2/ 144
1CNC System Installation
This section introduces how to install NcEditor V12 Laser Cutting CNC System,
including the following:
•Install hardware
•Install software
•Install driver
•Optional: Install a camera
1.1 Install Hardware
This section introduces how to install hardware of NcEditor V12 Laser Cutting
CNC System.
Before installing hardware, do the following:
•Check configuration.
•Confirm installation space.
To install hardware, do the following:
•Connect hardware.
•Install motion control card.
To get details of wiring inside hardware, see Wiring Diagram of Terminal Board,
Wiring Diagram of Drive and Wiring Diagram of Laser Device.
1.1.1 Check Configuration
To check whether the hardware that you have received is complete and correct, see
the following list:
•PM95A motion control card
•Lambda 5E terminal board
•EX30A terminal board (in position loop control mode) / EX33A terminal board
(in velocity loop control mode)
•EX31A terminal board (optional when exchanging workbench)
•SE001 follow-up amplifier
•Two DB9M/F communication cables
•One radio frequency cable
•One M16 tow cable with 4-core air plug
•WHB05S wireless handwheel / WHB05L wireless handwheel
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
3/ 144
1.1.2 Connect Hardware
To connect hardware, see the following wiring diagrams:
•In position loop control mode
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
4/ 144
•In velocity loop control mode
W-axis refers to the focus axis and B-axis refers to the rotation axis. To avoid being
confused with Y-axis in plane cutting configuration, Y-axis in tube cutting
configuration is U-axis.
When installing the follow-up amplifier, you need to ensure the outer metal part of
the amplifier surface is well installed on the machine tool because its coat is used to
shield all signals that interfere internal circuit. Mounting diagram is as follows:
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
5/ 144
1.1.3 Install Motion Control Card
NcEditor V12 Laser Cutting CNC System uses PM95A motion control card to mate
with NcEditor software, so as to control laser cutting rapidly and accurately.
Before installing motion control card, check whether the computer meets the
requirement according to the following list:
•CPU: basic frequency 1G or above
•Memory: above 1G
•Hard disk: above 20G
•Display adapter: 1024*864 at least (longitudinal resolution ≥ 864)
•Display: above VGA 14"
•CD-ROM: 4X or higher (optional)
•Main board extension slot: 1 or more PCI/PCIE slot
To install motion control card, do the following:
1. Power off the host computer and open the computer case.
2. Insert the motion control card into the PCI/PCIE slot.
3. Tighten the mounting screw and lid the computer case.
4. Restart the computer.
If NcEditor software cannot be run normally after the motion control card and
driver are installed, turn off the computer and check the connecting finger:
•If it is not clean, clear it with an eraser.
•If it is clean, change the motion control card.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
6/ 144
1.2 Install Software
This section introduces how to install software of NcEditor V12 Laser Cutting CNC
System, hereinafter referred to as NcEditor software.
Before installing the software, note the following:
•There must be a D disk in your computer, otherwise the installation will fail.
•NcEditor software is installed under directory C:\Program
Files\Weihong\NcEditor by default.
•If it is your first time to install the software, you need to install the basic
environment package first:
To install the software, do the following (If it is your first time to install the software,
skip steps 6 and 7):
1. Copy the installation package to your computer.
2. Unzip the installation package and double click . NcEditor Setup dialog
box pops up.
3. According to the prompt, select the display language between Chinese and
English.
4. According to the prompt, click Yes to start to update the system.
5. Optional: Close the running NcEditor software when a prompt Waiting for
closing NcEditor pops up.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
7/ 144
6. According to the prompt, click OK to delete files of the old version software and
avoid interfering the installation of the new version software.
7. Select one of the following parameter migration method and click Next:
–Reserve local parameters：use all parameters at the local.
–Restore the initial default parameters: use initial parameters in the
software.
上海维宏电子科技股份有限公司
SHANGHAI WEIHONG ELECTRONIC TECHNOLOGY CO., LTD.
8/ 144
–Update local parameters with installation package parameters：
use application parameters in the installation package:
•Apply local machine parameters: use machine tool parameters
at the local.
•Apply machine parameters in installation package: use
machine tool parameters in the installation package.
•Manually set machine parameters after software is installed:
use initialized machine tool parameters.
Machine parameters include the following:
•Double Y Origin Error (also called Double Y Gantry Initialization),
Detect Double Y Origin
•Origin Capacitance of Z-axis
•Parameters related to calibration
•Screw Error Compensation, Backlash Compensation
•Absolute Encoder Datum Value
The system starts to install driver automatically. See Automatically Install
Driver for details.
8. Select whether to put generated files and executive files separately according to
your need.
9. According to the prompt, click Yes to reboot the computer at once.
If you need to uninstall the software, do the following:
1. Delete NcEditor folder under directory C:\Program Files\Weihong.
2. Delete NcEditor shortcut on the desktop.
Andere Handbücher für NcEditor V12
1
Inhaltsverzeichnis
Andere WEIHONG Steuerungssystem Handbücher
WEIHONG
WEIHONG NK105 G2F Bedienungsanleitung
WEIHONG
WEIHONG NcEditor V12 Bedienungsanleitung
WEIHONG
WEIHONG NK280B Bedienungsanleitung
WEIHONG
WEIHONG PM53B Bedienungsanleitung
WEIHONG
WEIHONG NK280 Bedienungsanleitung
WEIHONG
WEIHONG NC65C Bedienungsanleitung
WEIHONG
WEIHONG NK105 Bedienungsanleitung
WEIHONG
WEIHONG 200 Series Bedienungsanleitung
WEIHONG
WEIHONG NK300CX Bedienungsanleitung
WEIHONG
WEIHONG Ncstudio V15 Bedienungsanleitung
