Wenglor SEFB Series Bedienungsanleitung

SEFBxxx

Multi-Beam Safety Light Array

Operating Instructions Translation of the Original Operating Instruction

Subject to technical changes

Available as PDF ﬁle only

Revision level: 06/09/2021

Doc. No.: 1038510

Version: 1.1.0

www.wenglor.com

2Table of Contents

Table of Contents

1. General 8

1.1 Information Concerning these Instructions 8

1.2 Target Group 8

1.3 Explanations of Symbols 8

1.4 Limitation of Liability 9

1.5 Copyrights 9

2. For Your Safety 10

2.1 Use for Intended Purpose 10

2.2 Use for Other than the Intended Purpose 11

2.3 Personnel Qualiﬁcations 11

2.4 Modiﬁcation of Products 11

2.5 Important Safety Precautions 12

2.5.1 Important Safety Precautions for Machine Manufacturers 12

2.5.2 Important Safety Precautions for Machine Operators 12

2.6 General Safety Precautions 12

2.7 Approvals and IP Protection 13

3. Product Description 13

4. Technical Data 15

4.1 General Technical Data 15

4.2 Response Times 17

4.3 Weight Tables 17

4.4 Housing Dimensions Safety Light Array 18

4.4.1 SEFB Muting 18

4.4.2 SEFB 19

4.5 Housing Dimensions, Mounting Technology 21

4.6 Control Panel 23

4.6.1 Control Panel Emitter 23

4.6.2 Control Panel Receiver SEFB Muting 23

4.6.3 Control Panel Receiver SEFB 24

4.7 Scope of Delivery 24

4.8 System Overview 25

4.9 Accessory Products 26

4.9.1 Mounting Elements 26

4.9.2 Connection Lines 26

4.9.3 Connection Cables 27

4.9.4 Safety Relays 28

Multi-Beam Safety Light Array 3

4.9.5 Path-Folding Mirrors 28

4.9.6 Safety Columns 30

4.9.7 IO-Link Master 31

4.9.8 T-Plug ZC7G001 (IO-Link Signal) 31

4.9.9 Muting Boom 32

4.9.10 Muting Connection Box ZFBB001 34

4.9.11 Laser Alignment Tool Z98G001 35

4.9.12 LED Light Strips Z99G001 35

4.9.13 microSD Card 35

4.9.14 Parametrization Software wTeach2 35

5. Project Engineering 36

5.1 Engineering 36

5.1.1 Safety Field 36

5.1.2 Securing the Danger Zone 37

5.1.3 Safety Clearance 38

5.1.3.1 General Information 38

5.1.3.2 Calculating the Safety Clearance 38

5.1.4 Minimum Clearance to Reﬂective Surfaces 42

5.2 Functions 44

5.2.1 Functions Overview 44

5.2.2 Combinable Functions 45

5.2.3 Operational Functions 46

5.2.3.1 Safety Operating Mode (Automatic Restart) 46

5.2.3.2 Start-Up Disabling and Restart Inhibit (RES) 46

5.2.3.3 Contactor Monitoring (EDM) 47

5.2.3.4 Beam Coding 47

5.2.3.5 Range 48

5.2.3.6 Cascading 49

5.2.3.6.1 Cascading via Extension Connection of the ESPE 50

5.2.3.6.2 Cascading via Muting Connection Box ZFBB001 50

5.2.3.6.3 Cascading of Other Safety Sensors with OSSD Outputs 51

5.2.3.6.4 Cascading of Contact-based Safety Components 51

5.2.4 Muting 52

5.2.4.1 Muting Signals 54

5.2.4.2 Muting Visualization 55

5.2.4.3 Cross Muting 55

5.2.4.4 Two Sensor Linear Muting 58

5.2.4.5 Four Sensor Linear Muting with Sequence Monitoring 60

5.2.4.6 Four Sensor Linear Muting with Time Monitoring 63

5.2.4.7 Muting Functions 66

5.2.4.7.1 Combinable Muting Functions 66

5.2.4.7.2 Muting Duration 66

5.2.4.7.3 Belt Stop Signal 67

5.2.4.7.4 Muting Enable 68

5.2.4.7.5 Direction Setting (Only for four sensor Muting) 69

5.2.4.7.6 Muting End Through Clearing of the ESPE 69

5.2.4.7.7 Partial Muting 70

5.2.4.7.8 Full Muting Enable 71

5.2.4.7.9 Gap Suppression 72

5.2.4.7.10 Override 72

5.2.5 Non-Safety-Related Functions 74

5.2.5.1 Measuring Function 74

5.2.5.2 Display Settings 76

5.2.5.3 Signal Output 76

5.2.5.4 Integrated Indicator Lamp 77

5.2.5.5 Signal Strength Display 77

5.2.5.6 Memory Function 78

5.2.5.6.1 Access to the Memory Card 79

5.2.5.6.2 Suitable Memory Cards 79

5.2.5.6.3 File System 79

5.2.5.7 Password Protection 80

5.2.5.8 IO-Link Interface (C/Q) 81

6. Transport and Storage 82

6.1 Transport 82

6.2 Storage 82

7. Installation 83

7.1 Positioning the ESPE 84

7.2 Installation with Mounting Bracket 86

7.2.1 Installation with Mounting Bracket ZEFX001 86

7.2.2 Installation with Mounting Bracket ZEFX002 87

7.2.3 Installation with Mounting Bracket ZEFX003 87

7.2.4 Installation with Mounting Bracket ZEMX001 88

7.2.5 Warning Strips 88

8. Electrical Connection 89

Table of Contents

Multi-Beam Safety Light Array 5

9. Parameters Conﬁguration 92

9.1 General 92

9.2 Preparation of the Parametrization 92

9.3 Parametrization of the Emitter 92

9.3.1 Default Settings 93

9.3.2 Calling up the Menu (User Level “Admin”) 93

9.3.3 Menu Structure 94

9.3.4 Parametrization of the Range and Coding 94

9.4 Parametrization of the receiver with basic function (without display) 95

9.4.1 Default Settings 95

9.4.2 Calling up the Menu (User Level “Admin”) 95

9.4.3 Menu Structure 96

9.4.4 Parametrization of the Restart Inhibit, Contactor Monitoring and Coding 97

9.5 Parametrization of the receiver with muting (with display) 98

9.5.1 Default Settings 98

9.5.2 Parametrization of the Restart Inhibit (RES) 101

9.5.3 Parametrization of the Contactor Monitoring (EDM) 101

9.5.4 Parametrization of the Beam Coding (CODE) 102

9.5.5 Parametrization Cascading (CASC) 103

9.5.6 Parametrization Muting (MUTG) 104

9.5.6.1 Parametrization Cross Muting (X) 105

9.5.6.2 Parametrization Two Sensor Linear Muting (2L) 108

9.5.6.3 Parametrization Four Sensor Linear Muting with Sequence (LSEQ) or Time Monitoring

(LTME) 111

9.5.7 Setting the Display (DISP) 114

9.5.8 Expert Menu (EXPT) 115

9.5.9 Saving the Conﬁguration and Restart (RUN) 120

9.6 Parametrization via the IO-Link Interface 121

9.6.1 Requirements and Framework Conditions 121

9.6.2 Process Data 123

9.6.3 Parameter Data 124

9.6.4 Example for Setting the Parameter Data 125

9.6.5 Data Storage 126

10. Initial Start-Up 127

10.1 Overview 127

10.2 Switching On 127

10.3 Aligning the Emitter and Receiver 128

10.4 Check for initial start-up 130

11. Operation 131

11.1 Operating Display 131

11.1.1 Operating Displays Emitter 131

11.1.2 Control Panel Receiver SEFB 132

11.1.3 Operating Displays Receiver SEFB Muting 133

11.2 Calling Up the Current Parametrization (“Worker” User Level) 135

12. Servicing 139

12.1 Maintenance 139

12.2 Cleaning 139

12.3 Regular Inspections 140

12.4 Annual Inspection 140

13. Diagnosis 141

13.1 Performance in Case of Fault 141

13.2 Error Indicators 141

13.2.1 Error Indicator on the Emitter 141

13.2.2 Error Indicator on the Receiver SEFB 142

13.2.3 Error Indicator on the Receiver SEFB Muting 142

13.3 Diagnosis Codes on the Receiver SEFB Muting 143

13.3.1 Codes for Information and Warnings 143

13.3.2 Codes for General Errors 143

13.3.3 Codes for Muting Errors 146

13.3.4 Codes when Accessing the Memory Card 147

14. Decommissioning 147

15. Proper Disposal 147

16. Appendix 148

16.1 Checklists 148

16.1.1 Checklist Initial Start-up 148

16.1.2 Checklist Annual Inspection 149

16.1.3 Regular inspection checklist 150

16.2 Connection Examples 151

16.2.1 Connection Example Start-Up Disabling and Restart Inhibit 151

16.2.2 Connection Examples Muting 152

16.2.3 Connection Examples Cascading 156

Table of Contents

Multi-Beam Safety Light Array 7

16.3 Order Notes 158

16.4 EU Declaration of Conformity 158

16.5 Index of Changes 158

16.6 Index of Abbreviations 159

16.7 Index of Figures 161

General

1. General

1.1 Information Concerning these Instructions

• These instructions apply to the following multi-beam Safety Light Arrays:

– SEFB

– SEFB muting

– For the exact order designation, see “16.3 Order Notes” on page 158

• They make it possible to use the product safely and efﬁciently.

• These instructions are an integral part of the product and must be kept on hand for the entire duration of its

service life.

• Local accident prevention regulations and national occupational health and safety directives must be ob-

served.

• The product is subject to further technical development, and thus the information contained in these operat-

ing instructions may also be subject to change.

The current version can be found at www.wenglor.com in the product’s separate download area.

NOTE!

The operating instructions must be read carefully before using the product and must be kept

on hand for later reference.

1.2 Target Group

• These operating instructions are aimed at developers, planners, installers, owners and machine operators

who want to safeguard their systems with safety technology from wenglor sensoric GmbH (referred to in the

following as “wenglor”).

• The instructions are also aimed at qualiﬁed specialist personnel, who are commissioning the SEFB multi-

beam Safety Light Array for the ﬁrst time, maintaining it or integrating it in a machine with accessories and

additional products where applicable.

1.3 Explanations of Symbols

• Safety precautions and warnings are emphasized by means of symbols and attention-getting words.

• Safe use of the product is only possible if these safety precautions and warnings are adhered to.

The safety precautions and warnings are laid out in accordance with the following principle:

ATTENTION-GETTING WORD!

Type and source of danger!

Possible consequences in the event that the hazard is disregarded.

• Measures for averting the hazard.

Multi-Beam Safety Light Array 9

The meanings of the attention-getting words, as well as the scope of the associated hazards, are listed

below:

DANGER!

This word indicates a hazard with a high degree of risk which, if

not avoided, results in death or severe injury.

WARNING!

This word indicates a hazard with a medium degree of risk which, if not avoided,

may result in death or severe injury.

CAUTION!

This word indicates a hazard with a low degree of risk which, if

not avoided, may result in minor or moderate injury.

ATTENTION!

This word draws attention to a potentially hazardous situation which, if not avoided, may

result in property damage.

NOTE!

A note draws attention to useful tips and suggestions, as well as information regarding

efﬁcient, error-free use.

1.4 Limitation of Liability

• The product has been developed in consideration of the current state-of-the-art, as well as applicable stan-

dards and guidelines. Subject to change without notice.

• A valid declaration of conformity can be found at www.wenglor.com in the product’s separate download

area.

• wenglor excludes all liability in the event of:

– Non-compliance with the instructions,

– Installation errors,

– Use of the product for purposes other than those intended,

– Use by untrained personnel,

– Use of unapproved spare parts and accessories,

– Unapproved modiﬁcation of products.

These operating instructions do not imply any guarantee from wenglor with regard to the described proce-

dures or speciﬁc product characteristics.

wenglor assumes no liability for printing errors or other inaccuracies contained in these operating instruc-

tions, unless wenglor was veriﬁably aware of such errors at the point in time at which the operating instruc-

tions were prepared.

1.5 Copyrights

• The contents of these instructions are protected by copyright law.

• All rights are reserved by wenglor.

• Commercial reproduction or any other commercial use of the provided content and information, in particu-

lar graphics and images, is not permitted without previous written consent from wenglor.

For Your Safety

2. For Your Safety

2.1 Use for Intended Purpose

The product is based on the following functional principle:

Safety light arrays

The light array monitors the safety ﬁeld between the transmitter and the receiver. If the safety ﬁeld is penetrat-

ed by an object, a switching command is triggered. This switching command may prevent initialization of a

hazardous machine motion, or may stop an action which has already been started.

As part of an overall system, the task of this product is to carry out safety-related functions. The correct over-

all function must be ensured by the system or machine manufacturer, however.

Use of this ESPE is only permissible if:

• The hazardous motion can be stopped electrically by the safety outputs of the ESPE.

• The safety clearance between the ESPE and a hazardous machine motion is complied with at all times.

• Additional mechanical safety equipment is installed so that the safety ﬁeld must be passed through to

access hazardous machine parts.

• Care is taken during installation to ensure that the personnel always remain inside the monitored zone for

machine operation.

• Regular safety inspections are carried out.

• Adequate detection of possible obstructions is assured with the existing number of beams.

• The use of a light array, type 4 / Performance Level PL e / SIL 3 / SIL CL 3, was deemed permissible follow-

ing an extensive risk analysis.

This product can be used in the following industry sectors:

• Special machinery manufacturing

• Pharmaceuticals industry

• Electronics industry

• Chemicals industry

• Heavy machinery manufacturing

• Clothing industry

• Glass industry

• Agriculture industry

• Logistics

• Plastics industry

• Steel industry

• Alternative energy

• Automotive industry

• Woodworking industry

• Printing industry

• Raw materials extraction

• Food industry

• Consumer goods industry

• Aviation industry

• Paper industry

• Packaging industry

• Construction industry

• Other

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Wenglor Scheinwerfer Handbücher

Wenglor

Wenglor SEMG4 Series Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung