Wheelock WHT-12 Bedienungsanleitung

P82774 C

Sheet 1 of 5

273 Branchport Ave.

Long Branch, N.J. 07740

(800) 631-2148 Thank you for using our products.

www.wheelockinc.com

INSTALLATION INSTRUCTIONS

STROBE APPLIANCES

Use this product according to this instruction manual. Please keep this instruction manual for future reference.

GENERAL:

The Strobe Appliances are UL Listed under Standard 1638 for outdoor Fire Protective Service. They are listed for outdoor use, wall

mount, with the backboxes specified in these instructions (See Mounting Option). The Strobe Appliances use a Xenon flashtube with

solid state circuitry enclosed in a rugged Lexanlens to provide maximum visibility and reliability for effective visible signaling. All

inputs are polarized for compatibility with standard reverse polarity supervision of circuit wiring by a Fire Alarm Control Panel

(FACP).

NOTE: All CAUTIONS and WARNINGS are identified by the symbol . All warnings are printed in bold capital letters.

WARNING: READ THESE INSTRUCTIONS CAREFULLY. FAILURE TO COMPLY WITH ANY OF THE

FOLLOWING INSTRUCTIONS, CAUTIONS AND WARNINGS COULD RESULT IN IMPROPER APPLICATION,

INSTALLATION AND/OR OPERATION OF THESE PRODUCTS IN AN EMERGENCY SITUATION, WHICH COULD

RESULT IN PROPERTY DAMAGE AND SERIOUS INJURY OR DEATH TO YOU AND/OR OTHERS.

WARNING: THE STROBE APPLIANCES ARE NOT TO BE USED AS AN INDOOR VISUAL EVACUATION

SIGNAL OR FOR THE HEARING IMPAIRED.

SPECIFICATIONS:

Table 1: UL Listed Models and Ratings

Outdoor

Plate2

Rated Input

Voltage Range

Nominal Input

Voltage

Rated Average

Current

Rated

Candela1

Mounting

Options

WHT-12 ---- 12VDC .150A 15cd B

WHT-24 18.0-31.0VDC 24VDC .075A 15cd B

WH1T-12 ---- 12VDC .150A 15cd C

WH1T-24 18.0-31.0VDC 24VDC .075A 15cd C

WH1T-115 ---- 115VAC .060A 15cd C

WH3T-12 ---- 12VDC .150A 15cd A

WH3T-24 18.0-31.0VDC 24VDC .075A 15cd A

WH3T-115 ---- 115VAC .060A 15cd A

WM3T-24 18.0-31.0VDC 24VDC .088A 117cd A

1At -35°C the following candela ratings apply: 117cd models = 78cd; 15cd models = 7.5cd

2W in models number indicates white or clear lens. Substitute R for optional red lens (does not apply to WM models). Derate

intensity by 60% for red lens.

WARNING: ALTHOUGH UL TESTING HAS VERIFIED THAT THESE STROBES FUNCTION EVEN AT 80% OF

THEIR MINIMUM RATING AND 110% OF THEIR MAXIMUM RATING, WHEELOCK STRONGLY RECOMMENDS

THAT THE VOLTAGE APPLIED TO THESE PRODUCTS BE WITHIN THEIR RATED INPUT VOLTAGE RANGE.

THE APPLICATION OF IMPROPER VOLTAGE MAY RESULT IN DEGRADED OPERATION OR DAMAGE TO

THESE PRODUCTS, WHICH COULD RESULT IN PROPERTY DAMAGE AND SERIOUS INJURY OR DEATH TO

YOU AND/OR OTHERS.

The UL Listed "Rated Input Voltage Range" is 18.0-31.0VDC for WHT-24, WH1T-24, WH3T-24, WM3T-24 and 12VDC for WHT-

12, WHIT-12, WH3T-12 using either filtered (DC) or unfiltered full-wave-rectified (FWR) voltage. Check the minimum and

maximum output of the power supply and standby battery and subtract the voltage drop from the circuit wiring resistance to determine

the applied voltage to the strobes.

P82774 C

Sheet 2 of 5

Figure 1.

(For full-wave-rectified input voltage,

multiply 1.41 by percent value shown in

Figure 1.)

WARNING: MAKE SURE THAT THE TOTAL AVERAGE CURRENT REQUIRED BY ALL APPLIANCES THAT

ARE CONNECTED TO THE SYSTEM’S PRIMARY AND SECONDARY POWER SOURCES AND APPLIANCE

CIRCUITS DO NOT EXCEED THE POWER SOURCES’ RATED CAPACITY OR THE CURRENT RATINGS OF ANY

FUSES ON THE CIRCUITS TO WHICH THESE APPLIANCES ARE WIRED. OVERLOADING POWER SOURCES OR

EXCEEDING FUSE RATINGS COULD RESULT IN LOSS OF POWER AND FAILURE TO ALERT OCCUPANTS

DURING AN EMERGENCY, WHICH COULD RESULT IN PROPERTY DAMAGE AND SERIOUS INJURY OR DEATH

TO YOU AND/OR OTHERS.

When calculating the total current: use Table 1 to determine the value of "Rated Average Current" for an individual strobe then

multiply this value by the total number of strobes; be sure to add the current for any other appliances, including audible signaling

appliances, powered by the same source and include any required safety factors.

WARNING: MAKE SURE THAT ALL FUSES USED ON SIGNALING CIRCUITS ARE RATED TO HANDLE THE

MAXIMUM INRUSH OR PEAK CURRENT FROM ALL APPLIANCES ON THOSE CIRCUITS. FAILURE TO DO THIS

MAY RESULT IN LOSS OF POWER TO THE SIGNALING CIRCUIT AND THE FAILURE OF ALL APPLIANCES ON

THAT CIRCUIT TO OPERATE, WHICH COULD RESULT IN PROPERTY DAMAGE AND SERIOUS INJURY OR

DEATH TO YOU AND/OR OTHERS.

When calculating the maximum inrush or peak current: use Figure 1 to determine the highest value of "Rated Inrush Current" for a

strobe (across the expected operating voltage range of the strobe); then multiply that value by the total number of strobes on the

circuit; be sure to add the inrush or peak currents from any other appliances, including audible signaling appliances, on that circuit

and include any required safety factors. The time duration of the maximum strobe inrush is shown in Figure 1.

CAUTION: Strobes are not designed to be used on coded systems in which the applied voltage is cycled on and off.

Table 3: Strobe Candela at Various Viewing Angles

Model

Voltage

Rated

Candela

Candela at Various Angles Per UL 1638

A1 A2 A3 A4 A5 A6/A7

12VDC 15.0cd 15.0 16.8 14.4 14.6 6.9 0.6

18.0-31.0VDC (24VDC) 15.0cd 15.0 18.8 13.7 15.6 7.4 0.9

115VAC 15.0cd 15.0 18.0 14.6 17.7 8.4 0.8

18.0-31.0VDC (24VDC) 117.0cd 117.0 15.2 16.4 6.0 7.0 1.2

Table 2.

Model Typical Flashes Per Secod Across Rated Voltage Range

WM3T-24 18 20 22 24 26 28 31

DC/FWR 0.7 0.8 0.9 1.0 1.1 1.2 1.3

NOTE: Typical flash rate for WH models is 1 per second at nominal

voltage.

P82774 C

Sheet 3 of 5

WIRING INFORMATION:

Figure 2. Figure 3.

1. Strobe Appliances have in-out wiring terminals that accepts two #12 to #18 American Wire Gauge (AWG) wires at each screw

terminal. Strip leads 3/8 inches and connect to screw terminals.

2. Break all in-out wire runs on supervised circuits to assure integrity of circuit supervision shown in Figure 3. The polarity shown

in the wiring diagrams is for the operation of the appliances. The polarity is reversed by the FACP during supervision.

GROUNDING: Connect ground wire to backbox. Install the lockwasher (provided in hardware bag) under head of each mounting

screw and mount strobe appliance to backbox.

MOUNTING OPTIONS:

CAUTION: The following figure shows the maximum number of field wires (conductors) that can enter the backbox used with

this mounting option. If these limits are exceeded, there may be insufficient space in the backbox to accommodate the field wires and

stresses from the wires could damage the product.

Although the limits shown for each mounting option comply with the National Electrical Code (NEC), Wheelock recommends use of

the largest backbox option shown and the use of approved stranded field wires, whenever possible, to provide additional wiring room

for easy installation and minimum stress on the product from wiring.

P82774 C

Sheet 4 of 5

MOUNTING PROCEDURES:

CAUTION: Check that the installed product will have sufficient clearance and wiring room prior to installing backboxes and

conduit, especially if sheathed multiconductor cable or 3/4" conduit fittings are used.

1. Mounting hardware for each mounting option is supplied.

2. Conduit entrances to the backbox should be selected to provide sufficient wiring clearance for the installed product.

3. When terminating field wires, do not use more lead length than required. Excess lead length could result in insufficient wiring

space for the signaling appliance.

4. Use care and proper techniques to position the field wires in the backbox so that they use minimum space and produce minimum

stress on the product. This is especially important for stiff, heavy gauge wires and wires with thick insulation or sheathing.

5. Do not pass additional wires (used for other than the signaling appliance) through the backbox. Such additional wires could

result in insufficient wiring space for the signaling appliance.

6. All models are UL Listed for outoor use with a temperature range of +31°F to +150°F (-35°C to +66°C) and maximum

humidity of 95% RH.

WARNING: A SMALL POSSIBILITY EXISTS THAT THE USE OF MULTIPLE STROBES WITHIN A PERSON'S

FIELD OF VIEW, UNDER CERTAIN CIRCUMSTANCES, MIGHT INDUCE A PHOTO-SENSITIVE RESPONSE IN

PERSONS WITH EPILEPSY. STROBE REFLECTIONS IN A GLASS OR MIRRORED SURFACE MIGHT ALSO

INDUCE SUCH A RESPONSE. TO MINIMIZE THIS POSSIBLE HAZARD, WHEELOCK STRONGLY RECOMMENDS

THAT THE STROBES INSTALLED SHOULD NOT PRESENT A COMPOSITE FLASH RATE IN THE FIELD OF VIEW

WHICH EXCEEDS FIVE (5) Hz AT THE OPERATING VOLTAGE OF THE STROBES (SEE TABLE 2 AND 3).

WHEELOCK ALSO STRONGLY RECOMMENDS THAT THE INTENSITY AND COMPOSITE FLASH RATE OF

INSTALLED STROBES COMPLY WITH LEVELS ESTABLISHED BY APPLICABLE LAWS, STANDARDS,

REGULATIONS, CODES AND GUIDELINES.

NOTE: NFPA 72/ANSI 117.1 conform to ADAAG Equivalent Facilitation Guidelines in using fewer, higher intensity strobes within

the same protected area.

CAUTION: Check the installation instructions of the manufacturers of other equipment used in the system for any guidelines or

restrictions on wiring and/or locating Notification Appliance Circuits (NAC) and notification appliances. Some system

communication circuits and/or audio circuits, for example, may require special precautions to assure electrical noise immunity (e.g.

audio crosstalk).

ANY MATERIAL EXTRAPOLATED FROM THIS DOCUMENT OR FROM WHEELOCK MANUALS OR OTHER

DOCUMENTS DESCRIBING THE PRODUCT FOR USE IN PROMOTIONAL OR ADVERTISING CLAIMS, OR FOR

ANY OTHER USE, INCLUDING DESCRIPTION OF THE PRODUCT'S APPLICATION, OPERATION, INSTALLATION

AND TESTING IS USED AT THE SOLE RISK OF THE USER AND WHEELOCK WILL NOT HAVE ANY LIABILITY

FOR SUCH USE.

IMPORTANT: READ SEPARATE "GENERAL INFORMATION" SHEET FOR INFORMATION ON THE

PLACEMENT, LIMITATIONS, INSTALLATION, FINAL CHECKOUT, AND PERIODIC TESTING OF NOTIFICATION

APPLIANCES.

P82774 C

Sheet 5 of 5

Limited Warranty

Wheelock products must be used within their published specifications and must be PROPERLY specified, applied, installed, operated,

maintained and operationally tested in accordance with these instructions at the time of installation and at least twice a year or more

often and in accordance with local, state and federal codes, regulations and laws. Specification, application, installation, operation,

maintenance and testing must be performed by qualified personnel for proper operation in accordance with all of the latest National

Fire Protection Association (NFPA), Underwriters' Laboratories (UL), Underwriters’ Laboratories of Canada (ULC), National

Electrical Code (NEC), Occupational Safety and Health Administration (OSHA), local, state, county, province, district, federal and

other applicable building and fire standards, guidelines, regulations, laws and codes including, but not limited to, all appendices and

amendments and the requirements of the local authority having jurisdiction (AHJ). Wheelock products when properly specified,

applied, installed, operated, maintained and operationally tested as provided above are warranted against mechanical and electrical

defects for a period of three years from date of manufacture (as determined by date code). Correction of defects by repair or

replacement shall be at Wheelock's sole discretion and shall constitute fulfillment of all obligations under this warranty. THE

FOREGOING LIMITED WARRANTY SHALL IMMEDIATELY TERMINATE IN THE EVENT ANY PART NOT FURNISHED

BY WHEELOCK IS INSTALLED IN THE PRODUCT. THE FOREGOING LIMITED WARRANTY SPECIFICALLY

EXCLUDES ANY SOFTWARE REQUIRED FOR THE OPERATION OF OR INCLUDED IN A PRODUCT. WHEELOCK

MAKES NO REPRESENTATION OR WARRANTY OF ANY OTHER KIND, EXPRESS, IMPLIED OR STATUTORY

WHETHER AS TO MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER MATTER.

USERS ARE SOLELY RESPONSIBLE FOR DETERMINING WHETHER A PRODUCT IS SUITABLE FOR THE USER'S

PURPOSES, OR WHETHER IT WILL ACHIEVE THE USER'S INTENDED RESULTS. THERE IS NO WARRANTY AGAINST

DAMAGE RESULTING FROM MISAPPLICATION, IMPROPER SPECIFICATION, ABUSE, ACCIDENT OR OTHER

OPERATING CONDITIONS BEYOND WHEELOCK'S CONTROL.

SOME WHEELOCK PRODUCTS CONTAIN SOFTWARE. WITH RESPECT TO THOSE PRODUCTS, WHEELOCK DOES

NOT WARRANTY THAT THE OPERATION OF THE SOFTWARE WILL BE UNINTERRUPTED OR ERROR-FREE OR

THAT THE SOFTWARE WILL MEET ANY OTHER STANDARD OF PERFORMANCE, OR THAT THE FUNCTIONS OR

PERFORMANCE OF THE SOFTWARE WILL MEET THE USER'S REQUIREMENTS. WHEELOCK SHALL NOT BE LIABLE

FOR ANY DELAYS, BREAKDOWNS, INTERRUPTIONS, LOSS, DESTRUCTION, ALTERATION, OR OTHER PROBLEMS

IN THE USE OF A PRODUCT ARISING OUT OF OR CAUSED BY THE SOFTWARE.

THE LIABILITY OF WHEELOCK ARISING OUT OF THE SUPPLYING OF A PRODUCT, OR ITS USE, WHETHER ON

WARRANTIES, NEGLIGENCE, OR OTHERWISE, SHALL NOT IN ANY CASE EXCEED THE COST OF CORRECTING

DEFECTS AS STATED IN THE LIMITED WARRANTY AND UPON EXPIRATION OF THE WARRANTY PERIOD ALL

SUCH LIABILITY SHALL TERMINATE. WHEELOCK IS NOT LIABLE FOR LABOR COSTS INCURRED IN REMOVAL,

REINSTALLATION OR REPAIR OF THE PRODUCT BY ANYONE OTHER THAN WHEELOCK OR FOR DAMAGE OF ANY

TYPE WHATSOEVER, INCLUDING BUT NOT LIMITED TO, LOSS OF PROFIT OR INCIDENTAL OR CONSEQUENTIAL

DAMAGES. THE FOREGOING SHALL CONSTITUTE THE SOLE REMEDY OF THE PURCHASER AND THE EXCLUSIVE

LIABILITY OF WHEELOCK.

IN NO CASE WILL WHEELOCK'S LIABILITY EXCEED THE PURCHASE PRICE PAID FOR A PRODUCT.

Limitation of Liability

WHEELOCK'S LIABILITY ON ANY CLAIM OF ANY KIND, INCLUDING NEGLIGENCE AND BREACH OF WARRANTY,

FOR ANY LOSS OR DAMAGE RESULTING FROM, ARISING OUT OF, OR CONNECTED WITH THIS CONTRACT, OR

FROM THE MANUFACTURE, SALE, DELIVERY, RESALE, REPAIR OR USE OF ANY PRODUCT COVERED BY THIS

ORDER SHALL BE LIMITED TO THE PRICE APPLICABLE TO THE PRODUCT OR PART THEREOF WHICH GIVES RISE

TO THE CLAIM. WHEELOCK'S LIABILITY ON ANY CLAIM OF ANY KIND SHALL CEASE IMMEDIATELY UPON THE

INSTALLATION IN THE PRODUCT OF ANY PART NOT FURNISHED BY WHEELOCK. IN NO EVENT SHALL

WHEELOCK BE LIABLE FOR ANY CLAIM OF ANY KIND UNLESS IT IS PROVEN THAT OUR PRODUCT WAS A

DIRECT CAUSE OF SUCH CLAIM. FURTHER, IN NO EVENT, INCLUDING IN THE CASE OF A CLAIM OF

NEGLIGENCE, SHALL WHEELOCK BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES

DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE

PRECEDING LIMITATION MAY NOT APPLY TO ALL PURCHASERS.

9/99

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Wheelock Scheinwerfer Handbücher

Wheelock

Wheelock SERIES VL Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung