Whelen Engineering Company 295HF100 Bedienungsanleitung

Page 1

Installation Guide:

295HF100 Siren Amplifier

Form No.13257C (050608)

ENGINEERING COMPANY INC.

51 Winthrop Road

Chester, Connecticut 06412-0684

Phone: (860) 526-9504

Fax: (860) 526-4078

Internet: www.whelen.com

Sales e-mail: autosale@whelen.com

Canadian Sales e-mail: autocan@whelen.com

Customer Service e-mail: custserv@whelen.com

Automotive: Sirens/Switches

Safety First

This document provides all the necessary information to allow your Whelen product to be properly and safely installed.

Before beginning the installation and/or operation of your new product, the installation technician and operator must

read this manual completely. Important information is contained herein that could prevent serious injury or damage.

• Proper installation of this product requires the installer to have a good understanding of automotive electronics,

systems and procedures.

• If mounting this product requires drilling holes, the installer MUST be sure that no vehicle components or other

vital parts could be damaged by the drilling process. Check both sides of the mounting surface before drilling

begins. Also de-burr any holes and remove any metal shards or remnants. Install grommets into all wire

passage holes.

• If this manual states that this product may be mounted with suction cups, magnets, tape or Velcro™, clean the

mounting surface with a 50/50 mix of isopropyl alcohol and water and dry thoroughly.

• Do not install this product or route any wires in the deployment area of your air bag. Equipment mounted or

located in the air bag deployment area will damage or reduce the effectiveness of the air bag, or become a

projectile that could cause serious personal injury or death. Refer to your vehicle owners manual for the air bag

deployment area. The User/Installer assumes full responsibility to determine proper mounting location, based

on providing ultimate safety to all passengers inside the vehicle.

• For this product to operate at optimum efficiency, a good electrical connection to chassis ground must be

made. The recommended procedure requires the product ground wire to be connected directly to the NEGATIVE

(-) battery post.

• If this product uses a remote device to activate or control this product, make sure this control is located in an

area that allows both the vehicle and the control to be operated safely in any driving condition. DO NOT

ATTEMPT TO ACTIVATE OR CONTROL THIS DEVICE IN A HAZARDOUS DRIVING SITUATION.

• It is recommended that these instructions be stored in a safe place and

referred to when performing maintenance and/or reinstallation of this

product.

• FAILURE TO FOLLOW THESE SAFETY PRECAUTIONS AND

INSTRUCTIONS COULD RESULT IN DAMAGE TO THE PRODUCT OR

VEHICLE AND/OR SERIOUS INJURY TO YOU AND YOUR PASSENGERS!

For warranty information regarding this product, visit www.whelen.com/warranty

DANGER! Sirens produces extremely loud emergency warning tones! Exposure to these

tones without proper and adequate hearing protection, could cause ear damage and/or hearing

loss! The Occupational Safety & Health Administration (www.osha.gov) provides information

necessary to determine safe exposure times in Occupational Noise Exposure Section 1910.95.

Until you have determined the safe exposure times for your specific application, operators and

anyone else in the immediate vicinity should be required to wear an approved hearing protection

device. FAILURE TO FOLLOW THIS RECOMMENDATION COULD CAUSE HEARING LOSS!

CAUTION

Loud siren noise can cause

hearing damage and/or loss.

Refer to OSHA Section 1910.95 prior

to putting ANY siren into service!

Wear

Protection!

ACTIVATION OF THIS

SIREN MAY DAMAGE

UNPROTECTED EARS!

Page 2

Installation:

The 295HF100, although technologically advanced, is simple to

install. An aftermarket center console is recommended for the

mounting location of the 295HF100. This not only allows the

driver to reach the controls easily, but also keeps the unit safely

out of the path of the vehicle’s SRS air-bag. Follow the console

manufacturer’s instructions for mounting information.

If a console-type mount is not possible, the 295HF100 includes

a bail strap mounting kit for over- or under-dash mounting.

The following steps will guide you through the

installation process:

Connecting the Power & Ground Wires:

RED (Power) and BLACK (Ground)

1. Remove the driver’s side front seat.

2. Remove the front, driver’s side rocker sill plate and kick panel.

3. Fold back the floor covering so that access is gained to the factory wire harness routed under the driver’s seat .

4. Insert the wiring harness into it’s port as shown in Fig. 1.

5. Extend the 2 RED and 2 BLACK wires toward the sill plate. Follow the same path as the factory wire harness.

WARNING: All customer supplied wires that connect to the positive terminal of the battery must be sized to

supply at least 125% of the maximum operating current and FUSED at the battery to carry that load. DO NOT

USE CIRCUIT BREAKERS WITH THIS PRODUCT!

6. Continue to follow the factory

harness through the firewall. To

pass the RED and BLACK wires

through, it may be necessary to

drill a hole in the firewall. If so, be

sure that there are no compo-

nents that will be damaged. After

the hole is drilled, insert a

grommet to protect the wires.

7. Route the RED and BLACK wires

along the factory harness

towards the battery.

8. Install 15 amp fuse block (user

supplied) on end of RED wire.

Note: Remove the fuse from the

fuse block before connecting any

wires to the battery!

9. Connect the fuse block wire to

the POSITIVE (+) terminal on the

battery. There must not be more

than two (2) feet of wire between

the fuse block and the battery. As

the wire between the fuse and

the battery is “unprotected”, do

not allow this wire to come in

contact with any other wires!

10. Connect the BLACK wire to the

factory chassis ground, adjacent

to the battery.

READ BEFORE INSTALLING!!!

Do not install this product or route any wires in

the deployment area of your airbag. Equipment

mounted or located in the airbag deployment area

will damage or reduce the effectiveness of the

airbag, or become a projectile that could cause

serious personal injury or death. Refer to your

vehicle owners manual for the air bag deployment

area.

The User/Installer assumes full responsibility to

determine proper mounting location, based on

providing ultimate safety to all passengers inside

the vehicle. Whelen Engineering Company

assumes no liability or responsibility for

determining individual applications or exact

installation location criteria.

910

COLOR & GAGE FUNCTION

RED 14GA

BLACK 14GA

BLUE 18GA

UNUSED(NO WIRE)

BLUE 18GA

BROWN 16GA

ORANGE 16GA

VIOLET 18GA

GRAY 18GA

WHITE 18GA

PIN #

+ BATTERY

GROUND

RADIO

N/A

RADIO

SPEAKER COM

+ SPEAKER

AUX. ENABLE

HORN

HORN/RING

N/A

INPUT CONNECTOR ASSEMBLY

Fig. 1

Page 3

Connecting the Speaker Wires (Orange & Brown)

1. Route the ORANGE and BROWN wires toward the vehicle’s siren speakers.

2. Connect the ORANGE wire to the POSITIVE speaker connection on speaker #1.

3. Connect the BROWN wire to the NEGATIVE speaker connection on speaker #1.

Connecting the Horn Relay Wires (White & Grey)

1. Route the WHITE and GREY wires along the factory wire harness and through the firewall at the same point as

the RED and BLACK wires.

2. Locate your vehicle’s horn relay and route the WHITE and GREY wires to this. If possible, follow the factory wire

harness to this relay.

3. Locate the wire that connects the vehicle horn to the horn relay.

4. Cut this wire.

5. Connect the WHITE wire to the wire coming from the horn relay.

6. Connect the GREY wire to the wire coming from the horn.

Note:The two (2) remaining BLUE wires are used to connect your two-way radio’s external speaker to the

295HF100-series siren for radio re-broadcast. This is an optional connection and does not effect the other

operations of the 295HF100-series siren.

Note:Radio re-broadcast will NOT work with amplified remote speakers! If your remote speaker is amplified

(I.E.: contains a power amp circuit in the speaker assembly), do not enable the radio re-broadcast feature.

1. Locate the two wires that connect the external speaker to the two-way radio.

2. Cut one of these wires and splice one of the BLUE wires into this circuit.

3. Cut the remaining speaker wire and splice the remaining BLUE wire into this circuit.

Connecting the 295HF100 to a Remote Control-Head (Optional):

The 295HF100 may be connected to an existing control-head, such as the Whelen PCC-S9N or equivalent. This is an

optional connection that enables the WAIL tone to be activated through the use of a PCC-S9N button or switch. If this

connection is not chosen, cut the VIOLET wire and cap the remaining stub to prevent accidental grounding of the wire.

15 AMP FUSE

(CUSTOMER SUPPLIED)

WHITE

GREY

ORANGE

BROWN

BLUE

VIOLET

BLACK

RED

WS295HF100

CHASSIS

GROUND

TWO-WAY

RADIO SPEAKER

REMOTE ACTIVATION

CONNECTION

(OPTIONAL)

+12V

HORN

RELAY

VEHICLE

HORN

CUT HERE

TO HORN RING

100W

SPEAKER

WS295HF100

WIRING DIAGRAM

Page 4

To Adjust The PA and Radio Repeat Levels: Before initial use, the PA and Radio Repeat output volume must be

adjusted to satisfactory operating levels. All 295HF100-series sirens utilize an internal potentiometer to control Radio

Repeat volume levels (see the “Radio Repeat Volume” section for adjustment information).

PA Volume - Public Address (PA) volume adjustments are

made with either an internal potentiometer or with a volume

knob, depending upon the model in question (see the “PA

Volume” section for adjustment information).

Radio Repeat Volume - If your model uses a potentiometer, locate the PA

adjustment port as shown. With the vehicle in an enclosed area, turn the Rotory

Knob to PA and speak into the microphone. While speaking, insert the screwdriver

and turn in a clockwise direction to increase the volume. Continue to increase the

PA volume until audio feedback occurs. Turn the screwdriver in a counter clock

wise direction to eliminate feed back and set the PA level to maximum volume.

For models with a PA Volume knob, follow the same procedures as above, except

that a screwdriver is not used. Simply make the adjustments using the knob.

Locate the Radio Repeat adjustment port (potentiometer) as shown. Set the volume level of the vehicle’s two-way

radio to it’s normal operating volume. Turn the Rotory Knob to RAD to activate Radio Repeat. Insert the screwdriver in

the Radio Repeat adjustment port and turn in a clockwise direction to increase the volume to it’s maximum volume.

Operating the 295HF100 Controls

Power Switch - This switch has two positions: Down (295HF100 - Off) and Up (295HF100 - On).

When this switch is in the Off position, the WS295HF100 will not function. When the switch is in

the On position the siren is functional and may be activated at the operator’s discretion. NOTE: If

the 295HF100 is connected to the vehicle’s horn ring circuit, the vehicle horn is disabled when the

295HF100 power switch is in the ON position.

MAN Button - The Manual button generates a variety of tones, depending on what position the

Rotary knob is in. For further explanation of this button’s function, refer to the Rotary knob section

of this manual.

Rotary Switch - The Rotary Knob controls the siren and PA (Public Address) functions of the

295HF100-series siren. There are 7 positions that may be selected. Each position and it’s function

is outlined on the next page:

PA Adjustment Port

WAIL

YELP

PIER

MIC

RAD

WAIL

YELP

PIER

MIC

RAD

PA Adjustment Knob

MAN

POWER

Radio Repeat

WAIL

YELP

PIER

MIC

RAD

Adjustment Port

MAN

POWER

RAD

MAN HF WAIL

YELP

PIER

RAD

FUNCTION

Page 5

RAD (Radio Repeat) - When the rotary knob is in the RAD position, any signal that is received by the vehicle’s

two-way radio will be simultaneously broadcast over the vehicle’s loudspeaker (the 295HF100 must be

connected to the two-way radio as outlined in this manual). This function overrides any other siren function.

PA (Public Address) - When the rotary knob is in the PA position, public address functions are operational.

Messages may be broadcast over the vehicle’s loudspeaker when the 295HF100 microphone is in use. If the

Manual button is pressed while the rotary knob is in this position, an “air horn” siren tone will be generated by

your vehicle’s loudspeaker. This tone is generated until the Manual button is released. The “air horn” may also

be generated by pressing the vehicle’s steering wheel horn button (if the vehicle’s horn has been wired to the

295HF100).

MAN (Manual Siren) - When the rotary knob is in the MAN position, pressing the Manual button generates a

tone that rises in pitch to a pre-set level. This tone is generated for as long as the Manual button is pressed. The

same tone may be generated by pressing the vehicle’s steering wheel horn button (if the vehicle’s horn has been

wired to the 295HF100). Please note that the 295HF100 microphone will override the siren function.

HF (Hands Free Operation) - When the rotary knob is in the HF position, the siren functions of the 295HF100

are placed in a stand-by mode. Siren tones are activated by a single “tap” on the MAN button or a single “tap” on

the vehicle’s steering wheel horn button (if the vehicle’s horn has been wired to the 295HF100). The first “tap”

produces a “Wail” tone (a steady, rise and fall tone). A second “tap” produces a “Yelp” tone (a fast, rise and fall

tone). A third “tap” produces a “PiercerTM” tone (an extremely fast, rise and fall tone). The next “tap” returns the

siren to a “Wail” tone and the cycle repeats itself. Two quick, successive “taps” will stop the siren.

WAIL (Wail Tone) - When the rotary knob is in the WAIL position, a steady, rise and fall tone is produced.

A single “tap” on the MAN button or a single “tap” on the vehicle’s steering wheel horn button (if the vehicle’s

horn has been wired to the 295HF100), changes the siren tone to a “Yelp” pattern (a fast, rise and fall tone). A

second “tap”, and the siren returns to a “Wail” tone. Please note that the 295HF100 microphone will override the

siren function.

YELP (Yelp Tone) - When the rotary knob is in the YELP position, a fast, rise and fall tone is produced. Pressing

the MAN button or the vehicle’s steering wheel horn button (if the vehicle’s horn has been wired to the

295HF100), changes the siren tone to a simulated air horn tone for as long as the button is pressed. Releasing

the button causes the siren to return to the Yelp tone. Please note that the 295HF100 microphone will override

the siren function.

PIER (Piercer TM Tone) - (NOTE: Some models may have a Hi/Lo tone instead of the PiercerTM tone) When the

rotary knob is in the PIER/Hi-Lo position, an extremely fast, rise and fall tone (alternating high and low tones for

Hi-Lo) is produced. Pressing the MAN button or a single “tap” on the vehicle’s steering wheel horn button (if the

vehicle’s horn has been wired to the siren), changes the siren tone to a simulated air horn tone for as long as the

button is pressed. Releasing the button causes the siren to return to the “Piercer TM ” (Hi-Lo) tone. Please note

that the microphone will override the siren function.

CAUTION

Loud siren noise can cause

hearing damage and/or loss.

Refer to OSHA Section 1910.95 prior

to putting ANY siren into service!

Wear

Protection!

ACTIVATION OF THIS

SIREN MAY DAMAGE

UNPROTECTED EARS!

Inhaltsverzeichnis

Andere Whelen Engineering Company Verstärker Handbücher

Whelen Engineering Company

Whelen Engineering Company X-ECUTOR 1 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company Epsilon 2S9 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company WS295HFS2 Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company Beta series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company Beta Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company X-ECUTOR 2 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company Epsilon 2S7 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 295HFSA1 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company GAMMA2 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 295SSA2 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 295SDA2 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company ALPHA12M Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company ALPHA22R Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 295SLS Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company Alpha Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company ALPHA22M Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company WPS-4000 Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 295HFANC Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company Beta Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company PAP112 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company COYOTE Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company Alpha Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 01-0886999-00 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company PAH112 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung