Whelen Engineering Company IS1 Series Bedienungsanleitung

ENGINEERING COMPANY, INC IS1 SERIES

MICRO SIZE

STROBE BEACONS

IS1224P, 12-48 VDC, PIPE MOUNT

IS1120P, 120 VAC, PIPE MOUNT

IS1224S, 12-48 VDC, SURFACE MOUNT

IS1120S, 120 VAC, SURFACE MOUNT

IS124CP, 12-48 VDC, CAST, PIPE MOUNT

Doc No. 04-0113085-01

Route 145, Winthrop Road

Chester, CT06412-0684

TELEPHONE: (860) 526-9504

TOLL FREE: 1-800-637-4736

1996 Whelen Engineering Company, Inc. Doc No. 04-0113085-01

May 24, 1996. 13085B

BASE

O RING SEAL

PCB ASSEMBLY

STROBE TUBE ASSEMBLY

#6-32 SCREW

CLAMP RING

DOME

STOP NUT

WARNING ALWAYS

DISCONNECT POWER

BEFORE SERVICING OR

INSTALLING AN IS1

SERIES BEACON.

SEE OTHER SIDE OF PAGE FOR

REPLACEMENT PARTS LISTING.

DESCRIPTION QTY. PART NUMBER

STROBE TUBE ASSEMBLY 1 01-0441319-00

DOME, AMBER 1 68-2130024-10

DOME, BLUE 1 68-2130024-20

DOME, CLEAR 1 68-2130024-30

DOME, GREEN 1 68-2130024-40

DOME, RED 1 68-2130024-50

O RING SEAL, PLASTIC BASE 1 38-0416442-00

GASKET, CAST BASE 1 38-0230104-00

MOUNTING INSTRUCTIONS

The IS1 Series Beacons are made for permanent

surface mount or pipe mount on a 1/2” NPT thread.

SURFACE MOUNT, PLASTIC BASE

1. Locate the wires in the wire slot and mount with

two screws. Make sure that the wires are in the wire

slot and not pinched under the Base.

PIPE MOUNT (Internal Thread)

1. Feed the power wires through the pipe.

2. Wire according to the WIRING instructions.

3. Screw the base onto the 1/2” NPT pipe and hand

tighten.

WIRING INSTRUCTIONS

MODELS IS1224P and IS1224S

MODEL IS124CP

1. Connect the RED wire to the positive DC

voltage (+).

2. Connect the BLACK wire to DC ground (-).

MODELS IS1120P and IS1120S

1. Connect the BLACK wire to the AC hot wire.

2. Connect the WHITE wire to the AC return wire.

Refer to the IS1 Series Product Sheet for current

draw to determine the proper wire gauge.

STROBE TUBE REPLACEMENT

1. Turn off power and wait 10 minutes.

2. Loosen the clamp ring screw and remove the

dome. Save the O Ring.

3. Press the tabs together on the Strobe Tube

Assembly and firmly pull the assembly out of the

PCB assembly. Do not pull the PCB Assembly away

from the Base.

4. Snap the replacement Strobe Tube Assembly into

the PCB Assembly. Roll the O Ring down the Base,

to get it in position. Position the Dome and secure

the clamp ring.

IS1 SERIES REPLACEMENT PARTS LISTING

3.4"

3.8" 2.5" DIA

1996 Whelen Engineering Company, Inc. Doc No. 04-0113085-01

May 24, 1996.

Dieses Handbuch passt für folgende Modelle

Andere Whelen Engineering Company Sicherheitssystem Handbücher

Whelen Engineering Company

Whelen Engineering Company 3012 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company Responder DX Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 6220-01-057-0746 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company B6LED Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company ISB Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company IPS 400 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 72000 Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company B6MM Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company RB6T Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company L21 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 295SLSA5 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company RB6PAPS Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company WPS-2900 Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company ECE ROTA-BEAM R416E Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company WeCanX Traffic Advisor Module Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 1502M Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company RB6 Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 295HFS6 Series Montageanleitung

Whelen Engineering Company

Whelen Engineering Company Super-LED L31HBF Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company 1010 Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company IS3 Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company Super-LED L32-Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company L22H Series Bedienungsanleitung

Whelen Engineering Company

Whelen Engineering Company L21LAM Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung