Whirlpool ADN203 C Bedienungsanleitung

ADN203 C

Instruction manual

Instructiuni de utilizare

Instrukcja obsługi

Návod na obsluhu

Mode d’emploi

Manuale d’istruzione







SAFETY INSTRUCTIONS

CAREFULLY READ THE INSTRUCTION MANUAL. If instructions are not followed,

there is a risk of injury, damage of the appliance and loss of the right to free warranty

service.

The Manufacturer shall not be held liable for damage arising from the failure to observe

the instructions contained in this manual.

We recommend to keep the Instruction manual the whole time you have the appliance.

When you sell the appliance pass the Instruction manual to the new owner of the

appliance.

–Do not cover the ventilation holes at the top and on the sides of the

appliance.

–Do not use electrical appliances inside the food storage compartments of the

appliance, unless they are of the type recommended by the manufacturer.

–If the supply cord is damaged it must be replaced by the manufacturer,

manufacturer service agent or a similarly qualified person, in order to avoid a

hazard.

–Disposal of the appliance should be according to national rules.

–Do not damage the appliance refrigeration system. It contains the refrigerant

gas R600a. If the refrigeration system is damaged:

•Do not use any open flame.

•Avoid sparks ― do not turn on any electrical appliances or lighting

fixtures.

•Immediately ventilate the room.

•Air the room in which the appliance is placed for a few minutes (the

size of the room for a product containing isobuthane / R600a must

be at least 4 m3) to avoid damage to the cooling system.

–Once the appliance is unpacked, make sure that it is complete, that the body

and the electrical cord aren’t damaged. It is forbidden to use a technically

damaged appliance.

CONNECTION TO THE MAINS

–The appliance should only be connected to an earthed socket installed in

accordance with the regulations. Make sure that the supply voltage

corresponds with the voltage marked on the rating label. This product

complies with all binding CE labelling directives. The earthed electrical socket

by which the appliance is connected to the mains should be in an accessible

place. It is a legal requirement that the appliance is properly earthed. The

manufacturer will not be held liable for any damage or injury which may result

from the failure to fulfil this requirement.

–To avoid the exposure to danger, always have faulty cable be replaced only

by the manufacturer, by our customer service or by qualified person and with

a cable of the same type.

–DO NOT USE extension cords or connectors (adapters), or hubs.

–The frequency and power of the electricity supply must conform to the

general data parameters of the appliance as it is shown in the product label.

–When positioning the appliance, be careful that the electrical cord isn’t

squeezed in order to avoid its damage. Do not store heavy objects such as

cooling devices, furniture or other domestic devices next the appliance in

such a way that they could squeeze and damage the electrical cord. This can

cause a short circuit and a fire.

–Make sure that the plug of the electrical cord is not squeezed by the back

wall of the appliance or otherwise damaged. A damaged plug can be the

cause of a fire!

–CAUTION! If the installed interior lighting or the advertising panel’s light-

emitting diode (LED) lamp for the cooling device is not functioning, contact

the maintenance and repair representative for replacements. LAMPS CAN

BE REPLACED ONLY BY THE MAINTENANCE AND REPAIR

REPRESENTATIVE.

•If the appliance is unplugged (for cleaning, moving to another place, etc.), IT

MAY BE REPEATEDLY SWITCHED ON AFTER 15 MIN.

•The appliance should be used only for storing foodstuffs.

•This appliance is not designed for the storage of explosive substances such as

aerosol cans with a flammable propellant.

•It is prohibited to store petrol and other flammable liquids near the appliance.

•The appliance can’t be disposed of by burning.

•Do not place any switched on electrical devices (such as microwave ovens,

hair dryers, irons, electric kettles or other electrical devices) on top of the

appliance because this may cause ignition of plastic parts.

•Do not place any dishes with liquids on top of the appliance and do not keep

flowers in vases or other liquid-filled vessels on the appliance.

•Do not climb on or sit on the appliance, do not lean on or hang on the

appliance doors and do not allow children to do this.

If the appliance is out of order and it is not possible to repair it by means of

given recommendations, unplug it, open the doors and call the service

expert. Only a service representative can remedy all technical or

construction faults.

GENERAL INFORMATION

The appliance is a vertical display cooler with glass doors and with a fan and is designed

for storage of foodstuffs and for chilling of drinks and for a short-term storage of them.

This appliance is intended for commercial use!

THE APPLIANCE IS ECOLOGICALLY CLEAN, CONTAINING NO MATERIALS HARMFUL TO

THE OZONE LAYER: the refrigerant used is R600a, the foaming agent used for the

appliance insulation is cyclopentane C5H10.

THE MANUFACTURER GUARANTEES RELIABLE OPERATION OF THE REFRIGERATOR

WHEN THE AMBIENT TEMPERATURE IS +16 TO +32 DEGREES CELSIUS AND THE

RELATIVE AIR HUMIDITY NOT GREATER THAN 60 PER CENT.

The appliance climate class is 3. Product temperature class –S

Product data sheet

Model

ADN203 C

Total gross volume, L

385

Net volume, L

360

Dimensions (H x W x D), cm

202,5 x 60 x 61

Shelf area, dm2

Rated current, A

1,5

Voltage used

220 –230 V / 50 HZ

Rated input, W

265

Products temperature ranges, °C (In accordance

with EU standard ISO 23953-2:2015, p .4.2.2)

from -2 to +14

Door opening area, m²

0,85

General product exposure area, m²

0,69

Loading of the refrigerator quantity of bottles,

pcs..: 0,33 l cans

0,5 l PET

426

224

Maximum loading of one shelf, kg

Energy consumption:

At switched on

lighting

At switched off

lighting

kWh/year

781

756

NOTE. The manufacturer reserves the right to make future changes to technical parameters and

specifications.

DESCRIPTION OF THE APPLIANCE, BASIC PARTS

See fig. 1, page 1

1 - THERMOSTAT DIAL. The temperature is indicated on the thermostat dial. Turning

the thermostat dial clockwise reduces the temperature in the chamber.

The fan for the appliance is activated and operates continuously.

2 - INTERIOR LIGHTING ON/OFF BUTTON. The interior lighting is switched on/off by

pressing this button. Symbol “|”:on; “O”: off.

3 - ADVERTISING PANEL LIGHT ON/OFF BUTTON. The advertising panel lighting is

switched on/off by pressing this button. Symbol “|”:on; “O”: off.

INSTALLATION AND OPERATING CONDITIONS OF THE

APPLIANCE

Preparing the appliance for operation

It is recommended to prepare the appliance for operation with a helper.

•Remove package. Lift the appliance away from foamed polystyrene base.

•Therefore take out adhesive tapes from sides and simply lift the appliance up and

take out the board. Strip adhesive tapes off and open the door. Remove the spacer

above the door.

•When positioning the appliance in chosen location, it will move more easily into

position if you lift the front a little and incline it backward allowing it to roll on its

casters. If your appliance is fit with screwed handles. Do not rise or push it

taking by handles.

If the appliance is brought in from the cold (temperature is not higher than +12

°C), you should wait for two hours before connecting it to the mains.

The appliance should not be connected to the mains until all packing and

transport materials aren’t removed. Suitably dispose the packaging material.

Positioning

•Place the appliance in a dry, well ventilated room

WARNING! The appliance should not be operated in an unheated room or

porch. Place the appliance away from heat sources such as kitchen

stove/oven, radiators, or direct sunlight.

WARNING! The appliance must not touch any pipes for heating, gas or

water supply or any other electrical devices.

Advertising panel

Fan

Thermostat knob

Shelves

Interior lighting on/off button

Condenser

Advertising panel light on/of button

Thaw water drip tray

LED lighting

Compressor

•Do not cover the ventilation holes at the top of the appliances –it must be a good air

circulation around the appliance. There should be a gap of at least 10 cm between

the top of the appliance body and any furniture that may be above it. If this

requirement is not followed, the appliance consumes more electrical energy and its

compressor may overheat.

•If the appliance is placed in a corner, a gap of at least 1 cm must be left between the

appliance body and the wall (see fig. 2, page 1).

•The appliance must stand on a level surface and must not touch the wall. If

necessary, regulate the height of the appliance by adjusting the levelling feet: by

turning them clockwise –the front of the appliance rises, by turning them counter

clockwise –it comes down. If the appliance is tilted slightly backward –the doors will

close by themselves.

TEMPERATURE REGULATION

The temperature in the refrigerator compartment is controlled using the thermostat

knob 2(see fig. 1) by turning it to one side or the other. The temperature indication in

digits is shown beside the thermostat knob.

The temperature is regulated on the scale of five digits.

0= Compressor is switched off WARNING! Electric current is not switched off.

1= highest temperature (lowest cooling)

5= lowest temperature (highest cooling)

If foodstuffs are too cold, set the thermostat knob to 1, 2or 3. If foodstuffs are not

being chilled sufficiently, set the thermostat knob to 4or 5. Please set the desired

temperature in the appliance according to your own requirements.

THE TEMPERATURE IN THE REFRIGERATOR COMPARTMENT MAY VARY

DEPENDING ON AMBIENT TEMPERATURE, THE AMOUNT OF FOODSTUFFS, THE

TEMPERATURE OF THE FOODSTUFFS, AND HOW OFTEN THE APPLIANCE

DOORS ARE OPENED AND CLOSED. Therefore we recommend:

•locate the appliance away from heat sources,

•appliance door must not to be left open,

•the appliance door should not be open longer than it is necessary to take out or put in

foodstuffs.

IF THE ROOM IS COOL, THE APPLIANCE COOLS LESS. THE TEMPERATURE IN THE

APPLIANCE MAY THEREFORE RISE. Use the thermostat wheel to set a lower

temperature.

DEFROSTING, CLEANING AND CARE

THE REFRIGERATOR COMPARTMENT DEFROSTS AUTOMATICALLY. Drops of ice that

form on the back wall of the refrigerator compartment thaw during the time the

compressor is not working and the thaw water runs down the thaw water runoff

channel to the tray on top of the compressor, where it evaporates.

REGULARLY CLEAN THE APPLIANCE.

Remember that before cleaning the back part of the appliance body

you must disconnect the appliance from the electrical energy supply

socket by pulling the plug out of the electricity outlet.

•Protect the appliance inner surfaces and plastic parts from fats, acids and sauces. In

case of accidental spills –immediately clean with warm soapy water or dishwashing

detergent. Wipe dry.

•Clean the appliance inner surfaces with warm soapy water. Dishwashing detergent

may also be used. Wipe dry inner and outer surfaces.

•Regularly clean the hermetic gaskets of the doors. Wipe dry.

•REGULARLY CLEAN THE THAW WATER CHANNEL SPACE WITH A

SPECIAL CLEANER FOR THAT PURPOSE (see fig.).

•At least once a year clean dust away from the back part of the

appliance body and the compressor. A soft brush, electrostatic cloth

or vacuum cleaner may be used for cleaning.

•DO NOT use detergents containing abrasive particles, acid, alcohol or

benzene for cleaning the appliance inner and outer surfaces. DO NOT

use for cleaning cloths or sponges that have coarse surfaces intended

for scrubbing. Outer of the doors –glass –clean with agents intended for glass

cleaning.

•IF THE APPLIANCE IS TO BE LEFT SWITCHED OFF FOR AN EXTENDED PERIOD,

LEAVE ITS DOORS OPEN.

Remarks on the appliance operating noise. As the appliance operates and

goes through the freezing cycle, various noises will be emitted. This is normal

and is not a sign of any malfunction.

•As the refrigerant circulates around the refrigeration system, it causes sounds like

murmuring, bubbling, or rustling.

•Louder sounds like popping or clicking may be heard for a short time as the

refrigerator compressor switches on.

CHANGING THE OPENING DIRECTION OF THE DOORS

It is recommended that changing the opening direction of the doors should be done

with a helper. When changing the opening direction of the doors YOU CAN NOT lay the

refrigerator horizontally!

Do the actions below in the order they are listed (see fig. 3, page 2):

1. Turn off the appliance and pull the plug out of the electricity supply

socket.

2. Remove the two screws (8) and separate the bottom bracket (10) together with the

washers and gaskets (9) on the small axle.

3. Remove the two screws (7)and separate the bracket (5) and the gasket (6).

4. Separate the door (4).

5. Remove the 4 screws (1) at the top of the advertising panel, separate the top of the

advertising panel (11), remove the front part of the advertising panel (12), and

then remove 4 screws (13) and separate the advertising panel; then loosen the 2

screws (14) and transfer the upper bracket (15) to the other side. Assemble the

advertising panel in reverse order.

6. Turn the door 180°, insert the upper axle and mount the door on it.

7. Remove the mounting screws (2)from the door, separate the handle (3) and attach

it by screwing the screws into the holes on same side.

8. Using the supplied washers and gaskets, attach the lower bracket (10) on the

opposite side of the cooler, but first attach the bracket axle to the door. Screw in

the bracket (5) on the opposite side of the cooler.

OPERATION PROBLEMS AND THEIR SOLUTIONS

(TROUBLESHOOTING). What if …

•The appliance is plugged in to the mains but it does not work. Check that

your house electricity supply installations are in order. Check that the plug is

correctly inserted into the electricity supply socket.

•The noise has become louder. Check that the appliance is standing stable, on a

level place. To make it level, regulate the front feet. Check if the appliance is not

touching any furniture, and that no part of the refrigeration system at the back part

of the appliance body is touching the wall. Pull the appliance away from any furniture

or walls. Check that the cause of increased noise isn’t due to bottles, cans or dishes

in the appliance that might be touching each other.

•Water has appeared at the bottom of the refrigerator compartment. Check

whether a thaw water channel space isn’t blocked. Clean the thaw water channel

space with a cleaner intended for that purpose.

•Water has appeared under the appliance. The thaw water collection tray has

slipped off the compressor. Place the tray on top of the compressor.

•When the appliance door is opened, the rubber sealing gasket pulls out. The

gasket is smeared with sticky foodstuffs (fat, syrup). Clean the sealing gasket and

the groove for it with warm water containing soap or dishwashing detergent and wipe

dry. Put the rubber sealing gasket back into the place.

•High temperature in appliance, the compressor operation pauses are short.

Ascertain whether the appliance door/doors are shutting tightly, whether the door

wasn’t kept open longer than necessary when taking out or putting in foodstuffs or

whether a large amount of warm food was placed in the appliance.

•The top of the appliance has condensation on it. The ambient relative air

humidity is above 60 %. Ventilate the room where the appliance stands and if

possible remove the cause of the humidity.

TRANSPORT

THE MANUFACTURER WILL NOT BE RESPONSIBLE FOR ANY DAMAGE OF THE

APPLIANCE THAT RESULTS FROM NON-COMPLIANCE WITH THE INSTRUCTIONS

FOR TRANSPORTATION.

•The appliance should be transported only in the vertical position.

•When being transported, the appliance should be protected from atmospheric

conditions (rain, snow, dampness).

•The appliance should be firmly secured in place while being transported, to avoid

slippage or any shocks in the transport vehicle.

•If the appliance was transported not vertically, it may be connected to the

mains after 4 hours at least. If this is not done, the appliance compressor

may fail.

Inhaltsverzeichnis

Sprachen:

Andere Whirlpool Kühlschrank Handbücher

Whirlpool

Whirlpool W10131410A Bedienungsanleitung

Whirlpool

Whirlpool CS25AEXHN00 Bedienungsanleitung

Whirlpool

Whirlpool 8S21FNI GD Bedienungsanleitung

Whirlpool

Whirlpool UC 148 Aut Technische Daten

Whirlpool

Whirlpool WRS325FDAB Montageanleitung

Whirlpool

Whirlpool Inglis IS22AGXTQ00 Bedienungsanleitung

Whirlpool

Whirlpool EDI9CK Bedienungsanleitung

Whirlpool

Whirlpool CT14NKXJN00 Bedienungsanleitung

Whirlpool

Whirlpool Roper RS22AQXKQ02 Bedienungsanleitung

Whirlpool

Whirlpool WF2T201 Bedienungsanleitung

Whirlpool

Whirlpool WH46TS1E Bedienungsanleitung

Whirlpool

Whirlpool REFRIGERATOR Bedienungsanleitung

Whirlpool

Whirlpool WT70E 831 X Bedienungsanleitung

Whirlpool

Whirlpool WRF535SMBB Gebrauchsanweisung

Whirlpool

Whirlpool ET22DM Bedienungsanleitung

Whirlpool

Whirlpool WRS312SNHW Installationsanleitung

Whirlpool

Whirlpool ED27DQ Bedienungsanleitung

Whirlpool

Whirlpool ET22MM Bedienungsanleitung

Whirlpool

Whirlpool WRT108TFYB Montageanleitung

Whirlpool

Whirlpool WRF767SDEM01 Bedienungsanleitung

Whirlpool

Whirlpool W10661460B Bedienungsanleitung

Whirlpool

Whirlpool REFRIGERATOR Bedienungsanleitung

Whirlpool

Whirlpool ENXTL 19 FL Series Bedienungsanleitung

Whirlpool

Whirlpool ES2FHAXSA00 Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung