Whirlpool ADN350S Handbuch

ADN350S

ADN480S

Instruction manual

Product Information Sheet

Instructiuni de utilizare

Fisa cu informatii despre produs

Instrukcja obsługi

Karta informacyjna produktu

Návod na obsluhu

Informačný hárok o produkte

Manuale d’istruzione

Scheda informativa sul prodotto

Návod k instalaci a obsłużę

Informační list produktu

Betriebsanleitung

Produktdatenblatt

Gebruiksaanwijzing

Productinformatieblad

Manual de instrucciones

Hoja de información del producto

Manual de instruções

Folha de informações do produto

Mode d’emploi

Fiche d'information sur le produit

AND350S







ADN480S







ADN350S



ADN480S

CAREFULLY READ THE INSTRUCTION MANUAL. If instructions are not followed, there is a

risk of injury, damage of the appliance and loss of the right to free warranty service.

The Manufacturer shall not be held liable for damage arising from the failure to observe

the instructions contained in this manual.

We recommend keeping the Instruction manual the whole time you have the appliance.

When you sell the appliance pass the Instruction manual to the new owner of the

appliance.

General information:

The appliance is industrial refrigerator - designed for storage of foodstuffs for a short-term

storage of them. This appliance is intended for commercial use!

SAFETY INSTRUCTIONS

General safety requirements:

–WARNING: Do not cover the ventilation holes at the top and on the sides of the

appliance.

–WARNING: Do not use any mechanical means or electrical devices to hasten the

thawing process when cleaning the freezer compartment.

–WARNING: Do not use electrical appliances inside the food storage

compartments of the appliance, unless they are of the type recommended by the

manufacturer.

–WARNING: When positioning the appliance, ensure the supply cord is not

trapped or damaged.

–WARNING: Do not locate multiple portable socket-outlets or portable power

supplies at the rear of the appliance.

–WARNING: Disposal of the appliance should be according to national rules.

WARNING: risk of fire / flammable materials. Do not damage the

appliance refrigeration system. It contains the refrigerant gas R600a. If

the refrigeration system is damaged:

•Do not use any open flame.

•Avoid sparks ― do not turn on any electrical appliances or lighting fixtures.

•Immediately ventilate the room. Air the room in which the appliance is placed for

a few minutes (the size of the room for a product containing isobuthane / R600a

must be at least 4 m3) to avoid damage to the cooling system.

C-Pentane is used as blowing agent in theinsulation foam and it is a

flammable gas.

–This appliance is not designed for the storage of explosive substances such as

aerosol cans with a flammable propellant.

–It is prohibited to store petrol and other flammable liquids near the appliance.

–The appliance should be used only for storing foodstuffs

Requirements for the connection to the mains:

–The appliance should only be connected to an earthed socket installed in

accordance with the regulations. This product complies with all binding CE

labelling directives. The earthed electrical socket by which the appliance is

connected to the mains should be in an accessible place. It is a legal

requirement that the appliance is properly earthed. The manufacturer will not be

held liable for any damage or injury which may result from the failure to fulfil this

requirement.

–The frequency and power of the electricity supply must conform to the general

data parameters of the appliance as it is shown in the product label.

–WARNING: If the supply cord is damaged: to avoid the exposure to danger,

always have faulty cable be replaced only by the manufacturer, by our customer

service or by qualified person and with a cable of the same type.

–Do not use adapters, multiple sockets and two-wire extension leads. If it is

necessary to use the extension lead, it must be equipped with a protection ring

and a single socket and must have a VDE/GS safety certificate.

–When positioning the appliance, be careful that the electrical cord isn’t

squeezed in order to avoid its damage. Do not store heavy objects such as

cooling devices, furniture or other devices next the appliance in such a way that

they could squeeze and damage the electrical cord. This can cause a short

circuit and a fire.

–Make sure that the plug of the electrical cord is not squeezed by the back wall

of the appliance or otherwise damaged. A damaged plug can be the cause of a

fire!

–CAUTION! If the installed interior lighting diode (LED) lamp for the cooling

device is not functioning, contact the maintenance and repair representative for

replacements. LAMPS CAN BE REPLACED ONLY BY THE MAINTENANCE

AND REPAIR REPRESENTATIVE.

Requirements for safe use:

–Once the appliance is unpacked, make sure that it is complete, that the body

and the electrical cord aren’t damaged. It is forbidden to use a technically

damaged appliance.

–If the appliance is unplugged (for cleaning, moving to another place, etc.), IT

MAY BE REPEATEDLY SWITCHED ON AFTER 15 MIN.

–When performing activities, such as cleaning, maintenance or moving, the

appliance must be completely disconnected from power supply (by pulling the

plug out from the socket). Do not pull on the cord, but hold the body of the plug

instead.

–Do not place any switched on electrical devices on top of the appliance because

this may cause ignition of plastic parts.

Do not place any dishes with liquids on top of the appliance and do not keep

flowers in vases or other liquid-filled vessels on the appliance.

–Do not climb on or sit on the appliance, do not lean on or hang on the appliance

doors.

–Do not use water spray and steam to clean the appliance.

Do not try repair the appliance on your own. If the appliance is out of order

and it is not possible to repair it by means of given recommendations, unplug

it, open the doors and call the service expert. Only a service representative

can remedy all technical or construction faults.

The appliance should be transported only in the vertical position.

The manufacturer will not be responsible for any damage of the appliance

that results from non-compliance with the instructions for transportation.

INSTALLATION AND OPERATING CONDITIONS

Positioning:

•This appliance can be installed in a dry, well ventilated indoor where the ambient

temperature corresponds to the climate class indicated on the rating plate of the

appliance.

WARNING! The appliance should not be operated in an unheated room or

porch. Place the appliance away from heat sources such as kitchen

stove/oven, radiators, or direct sunlight.

The rear wall of the appliance, in particular, the condenser and other

elements of the cooling system must not contact other elements, which may

damage them, (e.g. central heating pipes and the water supply pipes).

Minimum distances from the heat sources:

- from the electric gas and other ovens - 30 mm,

- from oil or coal fired ovens - 300 mm,

- from built-in ovens - 50 mm

If there is no possibility of ensuring the above- mentioned distances, provide an appropriate

insulation board.

•Do not cover the ventilation holes at the top of the appliances –it must be a good air

circulation around the appliance. There should be a gap of at least 10 cm between the top of

the appliance body and any furniture that may be above it. If this requirement is not

followed, the appliance consumes more electrical energy and its compressor may overheat.

•If the appliance is placed in a corner, a gap must be left between the appliance body and the

wall.

Overall space required for use and installation of the appliance:

For AND350S, see Page 1. Fig. 2

For AND480S, see Page 2, Fig. 5

•The appliance must stand on a level surface and must not touch the wall. If necessary,

regulate the height of the appliance by adjusting the levelling feet: by turning them clockwise

–the front of the appliance rises, by turning them counter clockwise –it comes down. If the

appliance is tilted slightly backward –the doors will close by themselves.

Preparing the appliance for operation:

It is recommended to prepare the appliance for operation with a helper.

•Remove package. Lift the appliance away from foamed polystyrene base.

•The device must only be transported in its vertical position; do not tilt any more than 30°.

•Therefore take out adhesive tapes from sides and simply lift the appliance up and take out

the board. Strip adhesive tapes off and open the door. Remove the spacer above the door.

•When positioning the appliance in chosen location, it will move more easily into position if you

lift the front a little and incline it backward allowing it to roll on its casters. When placing,

moving, lifting the appliance, do not hold the door handles, do not pull the

condenser at the rear part of the refrigerator and do not touch the compressor unit.

•For AND350S: Take two supports from the bag and insert them into the guides at the top

back part of the appliance (see fig. 3, page 1).

•For AND480S: Take out two supports 1from a bag and screw them by screws 2into

marked places at the back of a appliance (see page 2, fig. 6).

For AND480S: Take out the plug with the supply cord 11 from the water tray 12

(see page 2, fig. 4) which is placed under a compressor (this is intended for

transportation only. When the appliance is running, the cord can’t be in the

tray.

•The appliances should not be connected to the mains until all packing and

transport materials aren’t removed. Suitably dispose the packaging material.

•Once the unit has been positioned, wait for about 30 minutes before it is connected to the

mains.

•If the device has been tilted more than 30° during transport, allow it to

stand in an upright position for at least 4 hours before it is connected to

the mains. If this is not done, the appliance compressor may fail.

THE APPLIANCE BASIC PARTS

For AND350S, see Page 1. Fig. 1

For AND480S, see Page 2, Fig. 4

TEMPERATURE REGULATION

The temperature in the device compartment is controlled using the thermostat knob 2(see fig.

1 and fig. 4) by turning it to one side or the other.

Thermostat is switched off when in position 0: the compressor is switched off –electric current is not

switched off. Turning thermostat to any position (except 0) turns on the blower.

The temperature indication in digits is shown beside the thermostat knob. For model ADN350S:

when the door is closed, the temperature setting can be seen on the thermostat position

indicator display 3(see fig. 1, page 1).

ATTENTION! The numbers “0, 1, 2, 3, 4, 5”do not mean a specific temperatures.

The temperature is regulated on the scale of five digits.

0= Compressor is switched off WARNING! Electric current is not switched off.

1= highest temperature (lowest cooling)

5= lowest temperature (highest cooling)

THE TEMPERATURE IN THE DEVICE COMPARTMENT MAY VARY DEPENDING ON

AMBIENT TEMPERATURE, THE AMOUNT OF FOODSTUFFS, THE TEMPERATURE OF THE

FOODSTUFFS, AND HOW OFTEN THE APPLIANCE DOORS ARE OPENED AND CLOSED.

If the room is cool, the appliance cools less. The temperature in the appliance may

therefore rise. Use the thermostat wheel to set a lower temperature.

To avoid food contamination, follow the instructions below:

•Prolonged opening of the door can significantly increase the temperature in the compartments

of the appliance: only open the door for the time required to place / remove food.

•Regularly clean surfaces that may come into contact with food and accessible drainage

systems.

•Store fresh meat and fish in suitable containers in the refrigerator so that they do not come

into contact with or drip on other food.

•Do not put unpackaged food in the refrigerator.

•If the appliance is left empty for a long time, switch it off, defrost, clean, dry and leave the

door open to prevent mold from forming inside the appliance.

•Strictly adhere to the expiration date for foods as stated by the manufacturer on the product

packaging

Lighting switch

Shelves

Thermostat knob

Thaw water channel cleaner

Thermostat position indicator

Condenser

Electricity supply indicator. When the

appliance is connected to the electricity

supply, the green indicator light is illuminated.

Compressor

Interior light (LED)

Supply cord

Blower*

Thaw water drip tray

*Opening the door the blower switches off.

Blower switch

DEFROSTING, CLEANING AND CARE

THE THE APPLIANCE COMPARTMENT DEFROSTS AUTOMATICALLY. Drops of ice that form on

the back wall of the refrigerator compartment thaw during the time the compressor is not

working and the thaw water runs down the thaw water runoff channel to the tray on top of the

compressor, where it evaporates.

REGULARLY CLEAN THE APPLIANCE.

Remember that before cleaning the back part of the appliance body you must

disconnect the appliance from the electrical energy supply

socket by pulling the plug out of the electricity outlet.

•Protect the appliance inner surfaces and plastic parts from fats, acids and

sauces. In case of accidental spills –immediately clean with warm soapy

water or dishwashing detergent. Wipe dry inner and outer surfaces.

•Regularly clean the hermetic gaskets of the doors. Wipe dry.

•REGULARLY CLEAN THE THAW WATER CHANNEL SPACE WITH A SPECIAL

CLEANER FOR THAT PURPOSE.

•At least once a year clean dust away from the back part of the appliance

body and the compressor. A soft brush, electrostatic cloth or vacuum cleaner may be used for

cleaning.

•DO NOT use detergents containing abrasive particles, acid, alcohol or benzene for cleaning

the appliance inner and outer surfaces. DO NOT use for cleaning cloths or sponges that have

coarse surfaces intended for scrubbing. Outer of the doors –glass –clean with agents

intended for glass cleaning.

•IF THE APPLIANCE IS TO BE LEFT SWITCHED OFF FOR AN EXTENDED PERIOD, LEAVE ITS

DOORS OPEN.

CHANGING THE OPENING DIRECTION OF THE DOORS

It is recommended that changing the opening direction of the doors should be done with a

helper. You will need two spanners No. 8 and No. 10 and a Philips head screwdriver.

When changing the opening direction of the doors, YOU CAN NOT lay the appliance horizontally.

Do the actions below in the order they are listed:

WARNING! Turn off the appliance and pull the plug out of the electricity supply

socket.

For AND 350S (see page 3, fig. 7):

1. Remove the lower bracket 8 together with washers 6 on the axle and the plastic gasket 5, the

lower bracket 11 and the lower cover 10. Remove the refrigerator door.

2. Unscrew axle counterclockwise. Remove together with nut 1 and washers 3.

3. On the opposite side screw in the axle clockwise together with nut 1 and washers 3.

4. Insert the refrigerator door into the screwed-in axle 2.

5. Screw the lower cover 10 and the lower bracket 8 together with washers 6 onto the axle and

the plastic gasket 5 in place of the bracket 11. Screw the bracket 11 in place of the bracket 8.

6. Remove handle 12 and attach it on the opposite side. Plug up the remaining holes on the

right side with lids 13 in the sachet inside the refrigerator.

For AND 480S (see page 3, fig. 8):

1. Turn off the appliance and pull the plug out of the electricity supply socket.

2. Unscrew three screws 2 on the upper door suspension bracket 1, unscrew the axle 3 and turn

it towards the opposite side of the bracket.

3. Remove the door 4 by lifting it up;

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Whirlpool Kühlschrank Handbücher

Whirlpool

Whirlpool ED2FHEXT - 21.8 cu. ft. Refrigerator Bedienungsanleitung

Whirlpool

Whirlpool ED22DQ Bedienungsanleitung

Whirlpool

Whirlpool ET0MSRXTL - 9.7 Cubic Foot Refrigerator Montageanleitung

Whirlpool

Whirlpool WSF26D2EXF01 Bedienungsanleitung

Whirlpool

Whirlpool ET1MHKXMB02 Bedienungsanleitung

Whirlpool

Whirlpool W10855069A Bedienungsanleitung

Whirlpool

Whirlpool ED2GHEXNB05 Bedienungsanleitung

Whirlpool

Whirlpool REFRIGERATOR Bedienungsanleitung

Whirlpool

Whirlpool 4ET20ZK Bedienungsanleitung

Whirlpool

Whirlpool GI6SDRXXB Bedienungsanleitung

Whirlpool

Whirlpool W8CRNGMXQ Bedienungsanleitung

Whirlpool

Whirlpool ETl8AK Bedienungsanleitung

Whirlpool

Whirlpool EL87TRRRV - Satina-on - 35.3 Cu. Ft.... Bedienungsanleitung

Whirlpool

Whirlpool Roper RT21LMXKQ00 Bedienungsanleitung

Whirlpool

Whirlpool ET14EK Bedienungsanleitung

Whirlpool

Whirlpool REFRIGERATOR Bedienungsanleitung

Whirlpool

Whirlpool ED25DW Bedienungsanleitung

Whirlpool

Whirlpool EL88TRRWS Bedienungsanleitung

Whirlpool

Whirlpool ET1CHEXVB00 Bedienungsanleitung

Whirlpool

Whirlpool EDI9CK Bedienungsanleitung

Whirlpool

Whirlpool IT21AMXRQ00 Bedienungsanleitung

Whirlpool

Whirlpool 2262431 Bedienungsanleitung

Whirlpool

Whirlpool ARC 7658 IX Bedienungsanleitung

Whirlpool

Whirlpool ED5FVGXSS02 Bedienungsanleitung

Beliebte Kühlschrank Handbücher anderer Marken

Bonnet Neve

Bonnet Neve SKYVIEW PLUS Bedienungsanleitung

Zanussi Electrolux

Zanussi Electrolux ZERB 8441 Bedienungsanleitung

Sharp

Sharp SJ-BA31IEXW2-EU Bedienungsanleitung

CORBERO

CORBERO CC2300MCW Bedienungsanleitung

KitchenAid

KitchenAid 2205264 Bedienungsanleitung

Stengel

Stengel KU 1101 A++ Bedienungsanleitung

NEFF

NEFF KI181 Series Bedienungsanleitung

Hoshizaki

Hoshizaki Reach-In Bedienungsanleitung

Amana

Amana ASD2524VES00 Bedienungsanleitung

BOMANN

BOMANN KGC 213 Bedienungsanleitung

Danby

Danby DAR044A1SLDD Montageanleitung

Samsung

Samsung RF323TE Bedienungsanleitung

Beko

Beko CSA31022 Bedienungsanleitung

IKEA

IKEA FROSTIG C 185 E Bedienungsanleitung

Electrolux

Electrolux ER 6821 D Bedienungsanleitung

True

True TS-28 Bedienungsanleitung

Frigidaire

Frigidaire FSC23R5DW9 Bedienungsanleitung

Beko

Beko LSP4579W Bedienungsanleitung