Whirlpool 800 SERIES Bedienungsanleitung

Use & Care

MODELS: 800 and 900 Model Series

9871676

Compactor Safety ....................................2

Electrical Requirements............................3

How Your Compactor Works....................3

Parts and Features....................................4

Installing Your Compactor........................5

Unpacking Your Compactor ....................5

Space Requirements................................5

Freestanding and

Undercounter Installation ........................6

Adjusting the Toe Plate ............................7

Changing the Decorative Panel ..............8

Installing a Custom-Made Panel..............8

Changing the Standard Panel ..................9

Using Your Compactor ..........................10

900 Model Series ..................................11

800 Model Series ..................................11

Installing a New Bag ..............................12

Removing a Filled Bag ..........................12

Cleaning Your Compactor......................13

Troubleshooting ......................................14

Requesting Assistance or Service ........15

Warranty ..................................................16

In the U.S. for questions about features,

operation/performance, parts, accessories or service, call:

1-800-253-1301

In Canada, call for assistance:1-800-461-5681

for installation and service:1-800-807-6777

or visit our website at...

www.whirlpool.com

Whirlpool®

Compactors

You will be killed or seriously injured if you don't

follow instructions.

You can be killed or seriously injured if you don't

follow instructions.

All safety messages will identify the hazard, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Your safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all

safety messages.

This is the safety alert symbol.

This symbol alerts you to hazards that can kill or hurt you and others.

All safety messages will be preceded by the safety alert symbol and the word “DANGER” or

“WARNING.” These words mean:

DANGER

WARNING

Compactor Safety

IMPORTANT SAFETY INSTRUCTIONS

WARNING:When using an electrical appliance, basic precautions should always be followed, including the

following:

Read all instructions before using the compactor.

Close supervision is necessary when used by or

near children. Do not allow to be used as a toy, or

to run unattended at any time. Lock Key Switch

when not in use and store key out of reach of

children.

Do not touch moving parts.

Do not operate with a damaged cord set, plug,

motor, or after damage in any manner. Have the

compactor examined, repaired or adjusted by an

authorized serviceperson.

Use only for intended use as described in this

manual. Do not use other than manufacturer's

recommended attachments.

Do not take apart the compactor. Incorrect

reassembly can cause electric shock when

subsequently used.

Handle a loaded trash bag with care. Sharp objects

can pierce the bag and cause injury. Do not

overload trash bag with heavy material such as

glass.

■ This compactor is intended for household use only.

Do not compact toxic or volatile flammable material

such as oily rags and insect sprays. Do not compact

lighted cigarettes, cigars, or other hot or burning

items. Do not overload the compactor.

■

SAVE THESE INSTRUCTIONS

Electrical

Requirements

This compactor must be grounded while in use to reduce

the risk of electric shock. The compactor is equipped with

a three-conductor cord and three-prong grounding-type

plug to fit the proper grounding-type receptacle. The green

(or green and yellow) conductor in the cord is the ground-

ing wire. Never connect the green (or green and yellow)

wire to a live terminal. The outlet should be properly

installed and grounded in accordance with the National

Electrical Code and local codes and ordinances. No

adapter should be used with this appliance.

Recommended Grounding Method

This compactor is for use on a single phase, 115-volt, 60

Hz, AC only 15 or 20 ampere fused and properly ground-

ed circuit and is equipped with a grounding plug as shown

below. Time delay fuse or circuit breaker is recommend-

ed. It is recommended that a separate circuit serving only

this appliance be provided. In the event of an electrical

short circuit, grounding reduces the risk of electric shock

by providing an escape wire for the electric current. Do

not modify the plug attached to the compactor; use only

with a grounded receptacle.

wWARNING

Electrical Shock Hazard

Plug into a grounded 3 prong outlet.

Do not remove ground prong.

Do not use an adapter.

Failure to follow these instructions can result in

death, fire, or electrical shock.

How Your Compactor

Works

The compacting ram is the part of the compactor which

compresses the trash. The compacting ram does not go

to the bottom of the drawer. You will not see compact-

ing of trash the first few times you load the compactor.

NOTE: The compactor drawer should be about 1/2 full

before the compactor can begin to compress the load.

You may hear a noise when glass breaks. Strong glass bot-

tles may not break at all.

The trash in a full compactor bag will be about 1⁄4the size

of its original bulk.

Load bulky trash, bottles, and cans in the center of the

drawer. Bottles or cans not placed in the center may

become caught between the ram and the drawer. The

drawer monitor switch senses a “misload” and causes the

ram to return to the “up” position without compacting.

SOUND

CONDITIONED

START

OFF

TO PREVENT UNAUTHORIZEDTO PREVENT UNAUTHORIZED

USE OF THIS PRODUCTUSE OF THIS PRODUCT

TURN KEY KNOB TO OFF/LOCKTURN KEY KNOB TO OFF/LOCK

POSITION AND REMOVEPOSITION AND REMOVE

OFF/LOCK

1.DO NOT COMPACT AEROSOL CANS, FLAMMABLE OR POISONOUS MATERIALS.

2.REMOVE KEY KNOB TO PREVENT OPERATION BY CHILDREN.

3.DO NOT OVERFILL BAG OR ALLOW TRASH TO GET BEHIND OR

OVER THE SIDES OF THE CONTAINER.

WARNING:

TOAVOID THE POTENTIAL OF FIRE OR PERSONAL INJURY:

LOCK/OFF

START

12.

11.

10.

Parts and Features

1. Control pads

(for 900 Model Series)

2. Key-Knob START-OFF

switch

(for 800 Model Series)

3. Drawer monitor switch

4. Model-serial number label

5.Bag retainers

6. Optional bag carrier handle

7. Side-lock latch

8. Adjustable toe plate

9. TOUCH-TOE™ drawer opener

10.Reversible front panel

(only for 800 Model Series)

Wraparound panel

(only for 900 Model Series)

11. Drawer handle

12.ON-OFF Key Switch

(on some models)

IMPORTANT:

Installer: Leave Use and Care Guide with the homeowner.

Homeowner: Keep Use and Care Guide for future reference

and for local electrical inspector’s use, if required.

Space Requirements

Check the location where your compactor will be

installed. The cabinet opening should be square. You

should be able to fully open the compactor drawer. Six

inches (15.2 cm) of clearance is needed on the right side

of compactor drawer to be able to remove compactor

bag. Allow 23 inches (58.4 cm) in front of the compactor

to remove drawer.

341⁄8"

(86.7 cm)

24"

(61 cm)

15"

(38.1 cm)

The overall look of your compactor may vary.

Product dimensions

Installing Your

Compactor

leveling legs

4. Place the other two corner posts on the floor to the

side of the compactor. Grasp the sides of the com-

pactor cabinet and put compactor on its side on top of

the corner posts. Remove the shipping base from the

bottom of compactor.

3. Place two corner posts from carton on floor near com-

pactor. Open compactor drawer and remove any ship-

ping materials or other items shipped in the drawer. Do

not remove the compactor bag (if installed). Grasp the

handle and raise the front of drawer until it clears the

drawer stops. Grasp sides of drawer and lift drawer out

of compactor. Place the drawer on the two corner

posts.

Unpacking Your Compactor

IMPORTANT:

• Do not grasp console to move compactor.

• Begin in the room where the compactor will be

located.

1. Remove compactor from shipping carton. Remove

all protective packaging materials such as tape and

shipping pads. Remove waxy residue caused by pro-

tective shipping material with a mild solution of liquid

household cleaner and water.

2. Check that power supply cord is attached to the cord

clip on the rear of the compactor.

cord

clip

wWARNING

Excessive Weight Hazard

Use two or more people to move and install

compactor.

Failure to do so can result in back or other

injury.

1. Use pliers to lower leveling legs away from cabinet.

Place level inside on the floor of the cabinet. Check

that the compactor is level from front to back and side

to side. Adjust the leveling legs until the compactor is

level.

IMPORTANT:

• Do not grasp console to move compactor.

• Slide compactor onto cardboard or hardboard

before moving compactor across floor to prevent

damaging floor covering.

• Do not allow the rear frame of the compactor to

touch the floor covering when lifting or moving

compactor.

Freestanding installation:

2. Move the compactor close to its final position. Plug

the power supply cord into a 3-prong grounded outlet.

3. Carefully move compactor into its final position.

Check that compactor is still level. Repeat step 1

if necessary.

Freestanding and

Undercounter Installation

NOTE: Proper installation is your responsibility. Make

sure you have everything necessary for correct installa-

tion. It is the personal responsibility and obligation of the

customer to contact a qualified installer to assure that

electrical installation meets all national and local codes

and ordinances.

Tools and materials needed for installation:

Level Utility knife

Pliers Measuring tape

Scissors 5⁄16"box-end wrench

Phillips screwdriver Gloves

Flat-blade screwdriver

Undercounter installation:

NOTE: Installation hardware is not provided with full

cabinet models.

1. Measure the height of your cabinet opening. The top of

the compactor should be at least 1⁄8" (3 mm) from the

top of the cabinet opening.

The rear wheels are preset for a cabinet opening

height of 341⁄4" (87 cm) (Position “A”).

To adjust for other cabinet opening heights, loosen

screw just enough to clear stud from hole in position

“A”. Move the rear wheel and stud to position “B” or “C”

as needed for your cabinet opening measurement:

Position B: 341⁄4" to 347⁄16" (87 to 87.5 cm)

Position C: 347⁄16" to 345⁄8" (87.5 to 88 cm)

Tighten screw. Repeat for other rear wheel.

cabinet

locating stud

self-tapping

screw (pivot)

wheel

bracket

assembly

4. Grasp sides of compactor drawer and place bottom

of drawer into tracks. Lift at the handle so drawer will

go over drawer stops. Close drawer. Check if drawer

opens freely. If the toe plate rubs against floor, see the

“Adjusting the Toe Plate” section for further instructions.

18" min.

(45.7 cm)

24" min.

(61 cm)

Grounded

electrical outlet

must be

3" (7.6 cm) min.

from either side

wall.

6" (15.2 cm)

clearance to the

nearest vertical

wall on the right

side of compactor

is needed to

remove bag.

23" (58.4 cm) clearance in

front of the compactor is

needed to fully open or

remove compactor drawer.

151⁄4" min.

(38.7 cm)

341⁄4" min.

(87 cm)

Cutout dimensions

Clearance dimensions

Countertop mounting

mounting

screw

retaining

bracket

6. Grasp sides of compactor drawer and place bottom

of drawer into tracks. Lift at the handle so drawer will go

over drawer stops. Close drawer. Check if drawer opens

freely. If the toe plate rubs against floor, see “Adjusting

the Toe Plate” for further instructions.

Cabinet-front mounting

mounting

screw

retaining

bracket

mounting

clip

2. Use pliers to lower leveling legs away from cabinet.

Adjust legs so there will be a 1⁄8" (3 mm) to 1⁄4" (6.4 mm)

space between the top of the compactor and the top of

the cabinet opening. Stand the compactor upright.

3. For model with cabinet, remove the plastic plugs from the

compactor cabinet top.

4. Determine if you want the compactor frame or drawer

front flush with the cabinet front.

Using the two #8 -18 x 5⁄16" screws, install the retaining

brackets to cabinet top as needed:

If the compactor frame is to be flush with the cabinet

front, place retaining bracket screws through “A”.

If the compactor drawer front is to be flush with the

cabinet front, place retaining bracket screws through

“C”.

If the compactor is to be midway between “A” and

“C”, place retaining bracket screws through “B”.

retaining

bracket

countertop

5. Carefully lift the front slightly and roll compactor into

the cabinet opening.

Using the two #8 -18 x 1⁄2" screws, fasten the retaining

brackets to the underside of the countertop with the

mounting screws.

If brackets cannot be attached to the underside of

countertop, attach mounting clips to brackets. Fasten

compactor to cabinet front with mounting screws

through mounting clips.

Adjusting the Toe Plate

If the toe plate rubs the floor covering, the toe plate clear-

ance may be changed as follows:

1. Mark on each side of the toe plate the amount of toe

plate that rubs the floor covering.

2. Remove the drawer from the unit. (See step 3 in the

“Unpacking Your Compactor” section.)

3. Use a ruler and a pencil or chalk to draw a line

between the marks on each side of toe plate.

4. Use scissors or utility knife to cut toe plate along line.

5. Replace drawer. If toe plate still rubs floor covering,

repeat steps 1-4.

Changing the

Decorative Panel

900 Model Series :

2215⁄16"

(58.3 cm)

145⁄8"

(37.2 cm)

Raised panel: The outer section of panel must be 7⁄32"

(5.6 mm) thick to fit into trim. Decorative trim or raised panel

sections must be 5⁄16" (8 mm) from all edges of outer section.

1. Follow steps 1 through 4 “Changing the Standard Panel,”

but remove all the cardboard spacers.

2. Slide customized panel into trim.

3. Reattach handle.

4. Slide the drawer back in. (See “Replacing the Drawer”

in the “Cleaning inside the cabinet” section.)

Flat panel: A7⁄32" (5.6 mm) thick panel is required. This is the

same thickness as a standard 1⁄4" plywood or paneling.

Paint, wallpaper or other material

can be applied to the color panel.

A custom-made flat or raised panel

can be installed in place of the

color panel(s) and spacers (right).

Custom-made panel dimensions

7⁄32"

(5.6 mm) 5⁄16" (8 mm) all

around

outer section

of panel

raised

panel or

decorative

trim

145⁄8"

(37.2 cm)

2215⁄16"

(58.3 cm)

Installing a Custom-Made Panel

outside front

panel

spacers

drawer

trim

2313⁄16"

(60.5 cm)

145⁄8"

(37.2 cm)

Raised panel: The outer section of panel must be 7⁄32"

(5.6 mm) thick to fit into trim. Design raised panel sections

using dimensions shown above.

Trim for custom front panel

Order trim for installation of a custom front panel through

your Whirlpool dealer or by calling the Whirlpool

Consumer Assistance Center at 1-800-253-1301. In

Canada, call 1-800-807-6777.

Trims available for custom front panels are:

Part No. 9871381 (Brushed stainless steel)

Part No. 9871382 (White)

Part No. 9871383 (Black)

Part No. 9871384 (Almond)

Part No. 9871600 (Biscuit)

Custom-made panel dimensions

Flat panel: A7⁄32" (5.6 mm) thick panel is required. This is

the same thickness as a standard 1⁄4" plywood or paneling.

7⁄32"

(5.6 mm) 11⁄4"

(32 mm)

5⁄16"

(8 mm)

both sides

5⁄16"

(8 mm)

outer section

of panel

raised

panel or

decorative

trim

145⁄8"

(37.2 cm)

2313⁄16"

(60.5 cm)

The color panel on the front of your compactor’s drawer

reverses to another color. You may also be able to order

an extra color panel, depending on the model you have.

Contact your authorized Whirlpool dealer.

800 Model Series :

Changing the

Standard Panel

800 Model Series:

To change the color of your compactor’s front panel, fol-

low the directions below. All you need is a medium-sized

screwdriver.

Slide drawer out.

Remove two screws shown.

3. Remove handle.

4. Remove one cardboard spacer.

5. Remove the color panel. Be careful; edges may

be sharp.

6. Replace panel at front with desired color showing.

10. Slide drawer back in.

outside front

panel

spacers

drawer

trim

7. Make sure panel is all the way down.

8. Be sure to replace cardboard spacer in its former

position.

9. Replace handle and screws.

Using Your

Compactor

Open the drawer

Lift and pull the handle or press the drawer opener to

open the drawer.

wWARNING

Explosion Hazard

Do not compact any container, aerosol cans, or

cloths which might contain insecticide, hair

spray, engine starting fluid, paints, liquids,

thinners, or any other poisonous or explosive

products.

Doing so can result in death, explosion, or fire.

wWARNING

Cut Hazard

Do not push items down into compactor with

hands or feet.

Doing so can result in cuts.

Put in the trash

NOTE: You will not see compacting of trash the first

few times you load the compactor. The compactor

drawer should be about 1/2 full before the compactor

can begin to compress the load.

1. Wrap or cover wet or messy trash.

2. Load bottles or cans on their sides in the center of the

drawer.

3. Do not load bottles in an upright position in drawer as

shown here.

4. Do not compact items that may develop offensive

odors such as raw meat, fish, grapefruit rinds, dispos-

able diapers, or personal hygiene items.

Close the drawer

Push drawer in until it stops.

Andere Handbücher für 800 SERIES

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Whirlpool Müllpresse Handbücher

Whirlpool

Whirlpool 220-240~volt Bedienungsanleitung

Whirlpool

Whirlpool TU950QPXQ0 Bedienungsanleitung

Whirlpool

Whirlpool TU800SPPB1 Bedienungsanleitung

Whirlpool

Whirlpool TF4600X Series Bedienungsanleitung

Whirlpool

Whirlpool W10318827C Bedienungsanleitung

Whirlpool

Whirlpool TU950QPXS Bedienungsanleitung

Whirlpool

Whirlpool [12:36:03] ?????????????????: GC900QPPB Bedienungsanleitung

Whirlpool

Whirlpool GX900QPPB2 Bedienungsanleitung

Whirlpool

Whirlpool TU800SPPB2 Bedienungsanleitung

Whirlpool

Whirlpool TF 4600 Series Bedienungsanleitung

Whirlpool

Whirlpool TU800SPPB0 Bedienungsanleitung

Whirlpool

Whirlpool TRASH MASHER Bedienungsanleitung

Whirlpool

Whirlpool Compactor Bedienungsanleitung

Whirlpool

Whirlpool GARAGE COMPACTOR Bedienungsanleitung

Whirlpool

Whirlpool trash masher Bedienungsanleitung

Whirlpool

Whirlpool 4152821 Bedienungsanleitung

Whirlpool

Whirlpool TF 4500 Senes Bedienungsanleitung

Whirlpool

Whirlpool TU 4000 Series Bedienungsanleitung

Whirlpool

Whirlpool 800 SERIES Bedienungsanleitung

Whirlpool

Whirlpool GC900QPPB2 Bedienungsanleitung

Whirlpool

Whirlpool GX900QPPB1 Bedienungsanleitung

Whirlpool

Whirlpool Trash Masher JTF8500XL Bedienungsanleitung

Whirlpool

Whirlpool Trash Masher Bedienungsanleitung

Whirlpool

Whirlpool TU950QPXS Gebrauchsanweisung

Beliebte Müllpresse Handbücher anderer Marken

NuTone

NuTone 1050 Bedienungsanleitung

Rousseau

Rousseau R1C-SE19S Bedienungsanleitung

Kenmore

Kenmore 665.1361 Series Bedienungsanleitung

Newstripe

Newstripe Pack-Master Air Bedienungsanleitung

KitchenAid

KitchenAid KCCC151 Bedienungsanleitung

KitchenAid

KitchenAid KUCK03ITBL0 Bedienungsanleitung

Vestil

Vestil FM-T-DUMP Bedienungsanleitung

GE GCG1700P Handbuch

Euro Shatal

Euro Shatal RP4014-50 Bedienungsanleitung

third coast equipment

third coast equipment SP3410 Bedienungsanleitung

Cucine Oggi

Cucine Oggi EKKO CUBE 40 9000 Bedienungsanleitung

GE GCG1700II Bedienungsanleitung

Viking

Viking Designer Series Bedienungsanleitung

GE GCG1500RBB Handbuch

Centro

Centro 85-1066-6 (A01001 Kurzanleitung

Jenn-Air

Jenn-Air TC607X2 Bedienungsanleitung

Displays2go

Displays2go “THANK YOU” DUAL Bedienungsanleitung

GE Monogram ZCG3500DSS Bedienungsanleitung