White Rodgers UNP300 Verdrahtungsschema

For Installation Help

1-877-654-9394

White-Rodgers.com

For Installation HelpFor Installation Help

For Installation Help

For Installation Hel

877

654

9394

877 654 9394

hite-Rod

ers

0037-7258A

White-Rodgers

8100 West Florissant Avenue

St. Louis, MO 63136

UNP300 Non-Programmable Thermostat

with Home / Sleep / Away Presets

Installation Instructions & User Guide

Congratulations on the purchase of your White-Rodgers™thermostat!

Save these instructions for future use!

Questions? Contact White-Rodgers

™

customer service at 1-877-654-9394

ATTENTION: MERCURY NOTICE

This product does not contain mercury. However, this product may replace a

product that contains mercury. Mercury and products containing mercury must

not be discarded in household trash. Do not touch any spilled mercury. Wearing

non-absorbent gloves, clean up any spilled mercury and place in a sealed

container. For proper disposal of a product containing mercury or a sealed

container of spilled mercury, place it in a suitable shipping container.

Refer to www.White-Rodgers.com for location to send product containing

mercury.

These symbols are used throughout this User Guide.

Watch for them to identify:

Cautions

Tips

• Failure to read and follow all instructions carefully before installing

or operating this control could cause personal injury and/or

property damage.

• The thermostat may stop controlling temperature and your house

may freeze or overheat when batteries are too low. Batteries must

be changed when appears on the display.

Part 1: Before Getting Started ...................................................... Page 2

1.1 Check package contents

1.2 Answer questions about source of heating in your home

1.3 Assemble tools

1.4 Turn off power to your heating and cooling system

Part 2: Remove Old Thermostat and Install New Thermostat .... Page 4

2.1 Expose wires connected to old thermostat

2.2 Label and disconnect the wires

2.3 Install new thermostat’s wallplate

2.4 Match and connect wires

2.5 Install additional wiring (for Heat Pumps only)

2.6 Set switches

2.7 Install batteries

2.8 Snap thermostat to the wallplate

Part 3: Quick Setup..................................................................... Page 14

3.1 Get to know your thermostat

3.2 Set fan and system switches

3.3 Select options

3.4 Turn on power to your heating and cooling system

Part 4: Additional Thermostat Features.................................... Page 18

4.1 Set favorite temperatures (home / sleep / away)

4.2 Change batteries

4.3 Activate permanent auxiliary heat (for Heat Pumps only)

4.4 Set keypad lockout

4.5 Set change ﬁlter reminder

4.6 Adjust actual temperature display

Part 5: Troubleshooting Guide.................................................... Page 23

Appendix: Heat Pump Identiﬁcation .......................................... Page 25

TABLE OF CONTENTS

2 3

✔Do you have either oil or gas burning furnace?

✔Do you have a Heat Pump (and is it 1-stage or 2-stage)?*

✔Do you have Hydronic Heating (steam or hot water radiators or

radiant ﬂoor heating)?

You will need the following tools:

✔Flat-head screwdriver

✔2 AA alkaline batteries

You may also need:

✔Hammer

✔Drill with 3/16" (4 mm) bit

✔Small pliers to bend wires

Typically, this is achieved by ﬂipping a switch on the outside of the

furnace/air handler to the “OFF” position.

1.2 Answer questions about source of

heating in your home

1.3 Assemble tools

1.4 Turn off power to your heating and

cooling system

*To determine if you have a Heat Pump and/or whether it is

a 1-stage or 2-stage model, see the Appendix on the last page of

the Manual.

Do not turn the system back on until you have

completed the installation and set up of the thermostat.

Part 1 Before Getting Started

1.1 Check package contents

Open the package and verify that the following items are included:

•Thermostat (A) and Wallplate (B)

•Mounting screws and wall anchors (C)

•Wire Labels

•Heat Pump kit (D)

•Installation Instructions and User Guide

Before getting started, please review the following

pre-installation checklist.

If any of the items shown above are missing from your package,

call White-Rodgers™customer service at 1-877-654-9394 before

returning the thermostat to your place of purchase.

Y2 LYGW6W2

O/B

HEAT PUMP KIT

4 5

AUX

Part 2 Remove Old Thermostat and

Install New Thermostat

Do not disconnect wires from the old thermostat until you

label all the wires according to this manual.

2.1.1After turning off power to your heating & cooling system,

expose wallplate with wires and wire terminals. The required

steps vary depending on your old thermostat type.

2.1 Expose wires connected to

old thermostat

✔The Cover: This usually pulls off, but is sometimes secured by a

screw which must be loosened.

✔The Base: This either pulls off or needs to be removed by loosening

screws under the cover.

✔The Wallplate: This is removed by loosening the screws that hold

the thermostat to the wall.

Your old thermostat may consist of:

•3 parts: a cover, base and wallplate

•2 parts: a cover and wallplate

Wallplate

Base

Cover

3-Part unit

2-Part unit

6 7

✔ Ignore wire colors. There is no standard color code for

thermostat wires.

✔ Ignore existing wire labels, if they are present.

✔ Use the provided labels to label/re-label the thermostat wires.

✔ The new labels must remain on the wires at least until the

installation process is complete.

✔ No two wires can have the same label. wall

wall

2.1.2 Loosen all screws holding the old thermostat’s wallplate to

the wall.

Do not disconnect the wires from terminals. Allow

the wallplate to hang loosely on the wires.

Wall opening

Wallplate hanging on the wires

2.2.1 Note you may see two types of wiring in the old thermostat:

1. Wires leading from the wall to a

terminal on the thermostat

2. Wires connecting one terminal to

another (jumper wire).

These don’t have to be labeled.

2.2 Label and disconnect the wires

wall

8 9

R, 5, R5, RC or RH

W, 4, W1

W2, W-U

Y, Y1

L, F

X, C

wall

If terminal “O” is NOT wired.

If terminal “O” is wired.

If the OLD thermostat’s

terminal is wired into the wall

and identiﬁed by this letter…

…Then label its wire with

this letter:

You’ll need this information further in the installation process!

2.2.2 Label each wire that comes out of the wall and attaches to

terminals on the old thermostat. Use labels provided with your

new thermostat.

1. Note the letter printed near each wired terminal

2. For each out-of-the-wall wire:

– ﬁnd its terminal letter(s) in the left column of the table

on page 9,

– label the wire according to the right column of the table.

3. Circle all your out-of-the-wall labeled wires in the right column of

the table on page 9:

Mislabeling the wires could result in damage to your

heating and cooling unit.

Contact White-Rodgers™Customer Service at 1-877-654-9394 if:

✔You see RC and RH terminals not jumped together and both

wired into the wall.

✔Your old thermostat contains any wired terminals not listed in the

table on page 9.

Note: No thermostat installation uses all of the wires shown

on page 9. In most cases, between 4 and 5 terminals are wired.

wall

2.2 Label and disconnect the wires (cont.)

Example

10 11

2.2.3 After labeling all the wires, use a screwdriver to disconnect

each wire from its terminal. Remove the old thermostat.

Make sure that the wires don’t fall

into the wall after you detach them from

the old thermostat. You may choose to

tape them to the wall or tightly wind them

around a pencil or screwdriver.

Y2 L O/B Y G W 6 W2 C R

ELE SW5 SW1

GAS

2.3.1 Detach the new thermostat’s wallplate from the rest of the

thermostat and position the wallplate on the wall according to

the illustration below, passing the labeled wires through the

wire hole in the center of the wallplate.

2.3.2 With the wallplate

ﬂush against the

wall, mark

mounting holes

with a pencil.

2.3 Install new thermostat’s wallplate

Do not allow wires to touch each other or parts on

the thermostat. Doing so could result in damage to your heating and

cooling unit.

2.3.3 Move the wallplate aside. Drill the mounting holes using a 3/16"

drill bit. With a hammer, tap the wall anchors, provided in the

package, into the drilled holes.

2.3.4 Position the wallplate on the wall again and screw the mounting

screws into the wall anchors. Do not use a power screwdriver,

you may damage your thermostat.

Wallplate

Mounting hole

2.4 Match and connect wires

2.4.1 Match each wire coming from the wall to its corresponding

terminal, as shown in the illustration below. Insert each wire into

the hole on the side of its matching terminal. Using a screwdriver,

tighten the screw securely. DO NOT REMOVE THE WIRE LABELS.

A maximum of one wire from the wall can be wired

into each terminal.

No thermostat installation uses all of the wires shown below.

In most cases, between 4 and 5 terminals are wired. The remaining

terminals will not be used.

Y2 L Y G W 6 W2 C R

Y2 l O/B Y G W 6 W2 C R

12 13

Find two switches located on in the lower right corner of the wallplate

labeled ELE/GAS and O/B. Set them as follows:

2.6 Set Switches

• If you have either a gas or

oil furnace, set the switch to

GAS.

• If you do NOT have either a

gas or oil furnace, set the

switch to ELE (Electric).

• If you have NO wires labeled

O or B, set the switch to O.

• If a wire is labeled O, set this

switch to O.

• If a wire is labeled B, set this

switch to B.

If your HVAC system does NOT include a Heat Pump, continue to 2.6.

If your HVAC system includes a Heat Pump, in addition to wiring

described in point 2.4.1 connect thermostat terminals as shown

below. Use the jumper wires provided in the Heat Pump Kit, included

in the package. Secure the wires in the terminals by tightening the

terminal screws in a clockwise direction.

To determine if you have a Heat Pump and/or whether it is

a 1-stage or 2-stage model, see the Appendix at the end of this

manual.

2.5 Install additional wiring

(for Heat Pumps only)

Y2 L O/B Y G W 6 W2 C R

Install 2 AA alkaline batteries (not included) into the battery

compartment at the top of the thermostat wallplate.

2.8 Snap thermostat to the wallplate

2.7 Install batteries

Do not restore power to the heating and cooling system

until instructed.

Additional jumper wiring for 1-stage Heat Pump

Additional jumper wiring for 2-stage Heat Pump

Heat Pump kit

jumper wire

Heat Pump kit

jumper wires

Y2 L O/B Y G W 6 W2 C R

ELE SW5 SW1

GAS

ELE GAS

14 15

Part 3 Quick setup

3.1 Get to know your thermostat

Indicates

Permanent

Auxiliary

Heat Mode

(Heat Pumps

only)

Actual

Temperature

Favorite

Temperatures

Presets

Desired

Temperature

Control Panel

Buttons

1. Open the door on the right side of the cover and locate the FAN and

SYSTEM switches.

2. Set the FAN switch to AUTO.

3. Set the SYSTEM switch to COOL (to turn on cooling) or HEAT (to

turn on heating).

4. Press the DONE button.

3.2 Set fan and system switches

System Switch

Cool - Air Conditioning

Heat - Heating

Off - system turned off

Fan Switch

On - fan always on

for air circulation

Auto - fan runs

only when system

provides Heating or

Cooling

System Mode

Heating / Cooling

Indicates

System is

Currently

Providing

Heating or

Cooling

16 17

Options Default Setting Additional Information

1. Do you want ON Select default ON for now.

to be reminded (13 weeks) To modify a ﬁlter-change

when it is time to reminder, see Additional

change the air ﬁlter?

Features section 4.5.

2. Do you have a OFF If you do not have a Heat

Heat Pump? (no Heat Pump) Pump, select OFF.

If you do have a Heat Pump,

use the buttons

to select (On1) for a 1-stage

or (On2) for a 2-stage

Heat Pump.

Press the MENU button and, using the buttons, scroll down until

MORE OPTIONS is ﬂashing. Press OK.

You will be prompted to answer 5 “Options” questions.

•Use buttons to answer each question.

•Use buttons to advance to the next question.

3.3 Select options

When you have answered all 5 questions, press the DONE button.

Options Default Setting Additional Information

3. Do you want the FA Select SL (slow) if you

Cycle Rate to be (fast) have Hydronic (water

Fast or Slow? or steam) Heating.

Otherwise, use default FA.

4. Do you want °F

temperature (Fahrenheit)

displayed in °C

(Celsius) or °F

(Fahrenheit)?

5. How much 0(no offset) Select default 0for now.

displayed To adjust the displayed

temperature offset temperature reading, see

do you want? Additional Features

section 4.6

To determine if you have a Heat Pump and/or whether it is a

1-stage or 2-stage model, see the Appendix at the end of manual.

3.4 Turn on power to your heating and

cooling system.

Congratulations!

You have completed the basic setup of

your new thermostat. It’s ready to use.

To read about additional thermostat features, continue to section 4.

Navigation Buttons

Inhaltsverzeichnis

Andere White Rodgers Thermostat Handbücher

White Rodgers

White Rodgers 750 Bedienungsanleitung

White Rodgers

White Rodgers WHITE RODGERS 1E50N-303 Bedienungsanleitung

White Rodgers

White Rodgers 1F80-41 Bedienungsanleitung

White Rodgers

White Rodgers 1F87-0261 Bedienungsanleitung

White Rodgers

White Rodgers 1E30(W) Bedienungsanleitung

White Rodgers

White Rodgers 1F82-261 Bedienungsanleitung

White Rodgers

White Rodgers 1F93-380 Bedienungsanleitung

White Rodgers

White Rodgers 1F82-261 Bedienungsanleitung

White Rodgers

White Rodgers COMFORT-SET III 1F90-371 Bedienungsanleitung

White Rodgers

White Rodgers 1F86-241 Bedienungsanleitung

White Rodgers

White Rodgers 850 Bedienungsanleitung

White Rodgers

White Rodgers 1F89-211 Bedienungsanleitung

White Rodgers

White Rodgers 1E30-373 Bedienungsanleitung

White Rodgers

White Rodgers 1F82-51 Bedienungsanleitung

White Rodgers

White Rodgers 1F80-24 Bedienungsanleitung

White Rodgers

White Rodgers 1F97-1277 Bedienungsanleitung

White Rodgers

White Rodgers 1C20 Bedienungsanleitung

White Rodgers

White Rodgers 1C30(W) Bedienungsanleitung

White Rodgers

White Rodgers 1F90-71 Bedienungsanleitung

White Rodgers

White Rodgers 1F95W-71 Bedienungsanleitung

White Rodgers

White Rodgers 1E78-151 Installationsanleitung

White Rodgers

White Rodgers 1F56 Series Bedienungsanleitung

White Rodgers

White Rodgers 1F89-211 Bedienungsanleitung

White Rodgers

White Rodgers 1F85-277 Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung

Honeywell

Honeywell T6811 Bedienungsanleitung