Wi-Tek WI-CPE213-KIT Bedienungsanleitung

300Mbps Wireless

transmission equipment

WI-CPE213-KIT

Installation Guide

CPE exclusive for elevator

Product introduction

This product is suitable for elevator monitoring. there’s a pair of

devices on the fixed end and cage end. No debugging, easy

installation, anti-interference, three network ports, flexible power

supply, adjustable power, 100 meters high stable 4K video

transmission.

Plastic expansion nail

POE combiner

Screw spike

12V DC adaptor

Ribbon

Name

QTY

Fixed end

Cage end

12V DC adaptor

POE combiner

Ribbon

Expansion nail+screw spike

※If there is any damage or shortage of accessories, please contact the supplier in time.

Packing list

Fixed end *1

Cage end *1

Parameters

Antenna section

Parameters

Standard

IEEE802.11b/g/n(2T2R 300Mbps)

Working frequency

2400~2500MHz(frequencyextensionrangeis2312-2732MHz)

Antenna

Internal Antenna：gain 8dBi Horizontal 70 degrees, vertical 70 degrees.

Output power

20dBm

Rx sensitivity

-75dBm@MCS7

，

-100dBm@1Mbps

Max transfer rate

11n: 300Mbps(40M bandwidth),144Mbps(20M bandwidth)

11g: (54Mbps)

Hardware section

Voltage

24V POE or 12V DC

Interface

3x10/100M Base-TX(Cat.5/5E, RJ45)

Operating

Temperature

-30

~+65

Storage

temperature

-40

~+85

Operating humidity

5%~95%RH

Boundary

dimension

130*130*36mm

Firmware section

Fixed end

Cage end

Working mode

Wireless Client

SSID

“WlAN”+“Last 6 digits of MAC address”

Match SSID

Encryption

WPA2-PSK

Network mode

CPE

IP address

Dynamic DHCP

( default IP：192.168.1.88 )

Dynamic DHCP

( default IP：192.168.1.89 )

username

admin

password

admin

Note: when the device on both ends is charged, the device will

automatically establish a connection for about 1 minute.

Installation Guide on elevator

⑧ ⑨

⑥ ⑦

① ② ③ ④ ⑤

①

12V DC port

②

POE port

③Reset button

④

LAN1port

⑤

LAN2port

⑥

SYS indicator

⑦

POE indicator

⑧

LAN1indicator

⑨

LAN2indicator

Indicator description

Indicator

Panel

status

SYS indicator

SYS

red

Starting/Fault

blue

Working normally, pair successfully

Ethernet

indicator

Ethernet

Flash

Normal,data transmitting

Blue

Normal,no data transmission

Off

No device access

Interface

indicator

LAN1

Flash

Normal,data transmitting

Blue

Normal,no data transmission

Off

No device access

Interface

indicator

LAN2

Flash

Normal,data transmitting

Blue

Normal,no data transmission

Off

No device access

Hold Reset button for 10 seconds to restore factory the device.

Inhaltsverzeichnis

Andere Wi-Tek Drahtloser Zugangspunkt Handbücher

Wi-Tek

Wi-Tek WI-CPE211 Bedienungsanleitung

Beliebte Drahtloser Zugangspunkt Handbücher anderer Marken

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Bedienungsanleitung

Ubiquiti

Ubiquiti NanoStation NSM2 Bedienungsanleitung

Cisco

Cisco Aironet 1550 Series Bedienungsanleitung

Aruba

Aruba IAP-335 Bedienungsanleitung

Advantek Networks

Advantek Networks AWN-AP-54MR Bedienungsanleitung

IP-COM

IP-COM AP355 Bedienungsanleitung

Buffalo

Buffalo AirStation WLA-L11G Bedienungsanleitung

EnGenius

EnGenius EnStationACv2 Bedienungsanleitung

D-Link

D-Link DAP-3662 Bedienungsanleitung

xG Technology

xG Technology xMax CN1300 Bedienungsanleitung

Widelink

Widelink ezWave WAP-1100 Series Bedienungsanleitung

Edimax

Edimax CAP1200 Bedienungsanleitung

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Bedienungsanleitung

Aruba

Aruba AP-203R Bedienungsanleitung

LuXout Shades

LuXout Shades LUXSHADE MOTION Bedienungsanleitung

CreatComm

CreatComm TB5F Bedienungsanleitung

SineDigital

SineDigital MW-1500AP(H) Bedienungsanleitung

TP-Link

TP-Link AP9650 V1 Bedienungsanleitung