Williams Sound Transmitter T36 Bedienungsanleitung

Models PFM 360, PFM 330, PFM 360 RCH & PFM 330 RCH

Transmitter Model PFM T36

Optional Receiver Models PFM R36, R33

MAN 146B

Helping People Hear

™

manual & user guide

Wireless FM Listening System

Motiva™ Personal FM System

Models PFM 360, PFM 330, PFM 360 RCH & PFM 330 RCH

Manual and User Guide

System Overview 1

System Components 2

Safety Information 3

Recycling Instructions 3

Using the PFM T36 Transmitter 4

Using the PFM R33 / 36 Receiver 7

Belt Clip Installation 10

Channel Selection Chart 10

Battery Information 11

Limited Warranty 12

System Speciﬁcations 13

Fm Receiver, Model PFM R33 13

Fm Receiver, Model PFM R36 14

Fm Transmitter, Model PFM T36 15

System Overview

Thank you for purchasing a Motiva™ Personal FM System from Williams Sound Corp. Anyone needing

auditory assistance to overcome background noise, reverberation, or distance from a sound source

can beneﬁt from a Personal FM System.

Your PFM System has two principal parts: the Transmitter and the Receiver. Much like a miniature ra-

dio station, the Transmitter and microphone pick up the sounds you want to hear and broadcast them

over an FM radio signal. The receiver and earphone are used to pick up the broadcast up to 150 feet

away.

To avoid difﬁculties, please read through these instructions as you begin using the system. Then save

them for questions that arise as you continue to use your Williams Sound Personal FM System.

If you have problems with the PFM system, don’t hesitate to call us toll-free at 1-800-843-3544.

The speaker wears the belt-clip transmitter and a clip-on microphone. The speaker’s voice is broad-

cast as an FM radio signal over a distance of 150 feet. Listeners use the pocket receiver and

earphones or headphones to hear the speaker’s voice directly, with reduced background noise. An

optional neckloop telecoil coupler allows the system to be used with telecoil (T-switch) equipped hear-

ing aids.

Helping People Hear

System Components

Belt Clip Transmitter (PFM T36) with removable Belt Clip

Lavalier microphone (MIC 090)

Mini earphone (EAR 013)

Stereo auxiliary input cable (WCA 087)

System Carry Case (CCS 041)

Tuning Tool (PLT 011)

Instructions (MAN 146)

PFM System 330 Only:

Personal FM Receiver (PFM R33)

(4) AA Alkaline non-rechargeable batteries (BAT 001)

PFM System 360 Only:

Personal FM Receiver (PFM R36)

Environmental Plug-mount Microphone (MIC 014-R)

(4) AA Alkaline non-rechargeable batteries (BAT 001)

PFM System 330 RCH Only:

Personal FM Receiver (PFM R33)

(4) AA NiMH rechargeable batteries (BAT 026)

Drop-in Charger (CHG 3502)

PFM System 360 RCH Only:

Personal FM Receiver (PFM R36)

Environmental Plug-mount Microphone (MIC 014-R)

(4) AA NiMH rechargeable batteries (BAT 026)

Drop-in Charger (CHG 3502)

Helping People Hear

T36 R36 R33

Safety Information

Hearing Safety

CAUTION!

This product is designed to amplify sounds to a high volume level which could potentially cause

hearing damage if used improperly. To protect your hearing and the hearing of others:

1. Turn the volume down before putting on the earphone or headphone, and then adjust the volume

to a comfortable level.

2. Set the volume level at the minimum setting that you need to hear.

3. If you experience feedback (a squealing or howling sound), reduce the volume setting and move

the microphone away from the earphone or headphone.

4. Do not allow children or other unauthorized persons to have access to this product.

Battery Safety

CAUTION!

This product may be supplied with alkaline batteries. Do not attempt to recharge alkaline batter-

ies, which may explode, release dangerous chemicals, cause burns, or other serious harm to the

user or product.

Medical Device Safety

CAUTION!

1. Before using this product with an implantable or other medical device, consult your physician or

the manufacturer of your implantable or other medical device.

2. If you have a pacemaker or other medical device, make sure that you are using this product

in accordance with safety guidelines established by your physician or the implantable device

manufacturer.

Recycling Instructions

Battery Safety and Disposal

Help Williams Sound protect the environment! Please take time to dispose of your equipment

properly. Please do NOT dispose of batteries in the household trash. Please take the batteries to

a retail or community collection point for recycling.

Product Recycling:

Please do NOT dispose of your Williams Sound equipment in the household trash. Please take

the equipment to an electronics recycling center or return the product to the factory for proper

disposal.

Helping People Hear

Using the PFM T36 Transmitter

IMPORTANT: If Alkaline (nonrechargeable) batteries are being installed, slide the battery selec-

tion switch in the battery compartment to the “Alkaline” position. See FIG 1 below. If installing

NiMH (or rechargeable) batteries, slide the battery selection switch to the “NiMH” position.

1. Install two (2) AA batteries. Note: rechargeable batteries must be charged before use. See Bat-

tery Information on page 11.

2. Plug the microphone cord into the “Mic Jack” ( ) on top of the transmitter.

3. Optionally, plug in a desired audio source such as a CD or MP3 player using the “Auxiliary Input”

jack (WCA 087 stereo auxiliary input cable included). If the microphone and an auxiliary source are

used together, the audio will be mixed. If only the auxiliary source is desired, the microphone can

be muted. Do not remove the microphone from the “Mic Jack” as the microphone’s cable is also the

transmitting antenna!

4. Turn the unit on: press and hold the “ON/OFF/MUTE” button for three seconds. The “Power On”

indicator ( ) should illuminate green.

5. Select the desired operating frequency. Use the “Channel Selector” knob to select any of the 16

available channels on 72-76 MHz. Refer to the channel selection chart (FIG 9, Page 10). Make

sure the receiver being used is operating on the same frequency as the T36 transmitter.

6. Place the transmitter in a pocket, or clip it onto a belt or waistband (See “BELT CLIP INSTALLA-

TION”, page 10).

–

Comp

CH Lock

- Gain + -

AUX

2:1

1:1

Mic Jack

Channel

Selector

Power On Indicator

Auxiliary

Input

Power On/Off/Mute

Mic Jack

Channel

Selector

Power On Indicator

Auxiliary

Input

Power On/Off/Mute

Mic Jack

Channel

Selector

Power On Indicator

Auxiliary

Input

Power On/Off/Mute

FIG. 1: Battery Selection Switch

FIG. 2: T36 User Controls

Helping People Hear

7. Lapel clip microphones should be attached to a collar or lapel, as close to the speaker’s mouth

as practical. If using an optional headset microphone, position the mic as close to the side of the

mouth as possible without touching the mouth See FIG 3.

8. To mute the microphone, press the “ON/OFF/MUTE” button momentarily. The “ON/OFF/MUTE” but-

ton will ﬂash red. To unmute the microphone, press the “ON/OFF/MUTE” button momentarily again.

IMPORTANT: When the T36 transmitter is not being used, remember to turn the unit OFF by press-

ing and holding the “ON/OFF/MUTE” button for three seconds. The Power On indicator will not be lit.

GAIN CONTROL

The gain control can be used to adjust the volume level on both the microphone and auxiliary input. To

adjust the volume level, open the battery door and locate the Gain Control (see FIG 4). Use the sup-

plied small screwdriver and rotate to increase “+” or decrease “-” the gain.

FIG. 3: Lapel Microphone Placement

Helping People Hear

–

Comp

CH Lock

- Gain+ -

AUX

2:1

1:1

FIG. 4: ConFIGuration Controls

1 2 3 4

1. Gain Control 3. Compression Selector

2. Auxiliary Input Level 4. Channel Lock

Ye s Ye s No

Helping People Hear

AUXILIARY INPUT LEVEL

The auxiliary input level can be used to adjust the auxiliary input level only. To adjust, open the battery

door and locate the Auxiliary Input Level (see FIG 4). Use the supplied small screwdriver and rotate to

increase “+” or decrease “-” the input level.

Note: When using an auxiliary audio source, if the “Aux Input Level” is set too high, there can be

increased audio distortion and decreased battery life.

Note: Microphone cable serves additional purpose as the transmitting antenna; therefore must remain

plugged in during Aux cable use.

COMPRESSION SELECTOR

By default, the T36 compression is set to “Off” for normal operation, or “1:1” compression. For hear-

ing assistance applications, the compression selector can be set to “On” for “2:1” compression.

To change this setting, open the battery door and locate the Compression Selector (FIG 4). To turn on

compression, use the supplied small screwdriver and slide the “Comp” switch to the position marked

“2:1”. To turn off compression, slide the “Comp” switch to the position marked “1:1”.

CHANNEL LOCK

By default, the T36 channels are unlocked to allow the user to change frequencies as needed. If de-

sired, channels can be locked to prevent users from changing the channels.

Note: The Channel Lock only locks the electronic frequency; it does not physically lock the channel

selection knob.

To lock or unlock channels, open the battery door and locate the Channel Lock (FIG 4). To lock the

current channel while the unit is on, slide the “CH Lock” switch to the position marked ( ). To

unlock the channels, use the supplied small screwdriver and slide the “CH Lock” switch to the position

marked ( ).

LOW BATTERY INDICATOR

The “Power On” indicator (see FIG 2) will ﬂash to indicate low battery.

BATTERY LIFE EXPECTANCY AFTER LOW BATTERY SIGNAL

Transmitter Receiver

Alkaline 90 min. Alkaline 60 min.

NiMH 15 min. NiMH 15 min.

–

Comp

CH Lock

- Gain+ -

AUX

2:1

1:1

–

Comp

CH Lock

- Gain+ -

AUX

2:1

1:1

Using the PFM R33 / R36 Receiver

IMPORTANT: If Alkaline (nonrechargeable) batteries are being installed, slide the battery selec-

tion switch in the battery compartment to the “Alkaline” position. See FIG 5 below. If installing

NiMH (or rechargeable) batteries, slide the battery selection switch to the “NiMH” position.

1. Install two (2) AA batteries. Note: rechargeable batteries must be charged before use. See Bat-

tery Information on page 11.

2. (Applies only to R36) Insert the small plug mount microphone (MIC 014) into the “Mic Jack” ( )

on the top of the receiver. See FIG 7 below.

3. Plug the earphone or headphone into the “Headphone Jack” ( ) on top of the receiver. See FIG 8 /

FIG 9. Place the headphones on your head or earphone in your ear.

4. Turn the power on by rotating the “On/Off/FM Volume” knob clockwise. The “Power On Indicator”

( ) should illuminate green.

5. Select the desired operating frequency. Locate the “Channel Selector” inside the battery door (See

FIG. 5). Use the supplied small screwdriver to rotate the switch to the desired channel (See FIG. 9,

Page 10: Channel Selection Chart).

Helping People Hear

FIG. 5: Battery Selection Switch /

ConFIGuration Controls

1 2 3 4

1. Squelch 3. Channel Selector

2. Tone Control 4. Max Gain Control

Battery Selection Switch

FIG. 6: R33 Top View FIG. 7: R36 Top View

Helping People Hear

6. Adjust the receiver tone control to your needs. Locate the tone control inside the battery door. Use

the supplied small screwdriver to rotate the “Tone Control”. A low setting (fully counter-clockwise

“-”) emphasizes lower frequencies. A medium setting (rotated to a vertical position) has some low

frequency cut. A high setting (fully clockwise “+”) maximizes low frequency cut and emphasizes

higher frequencies.

Note: the earphone cord is also the receiving antenna. Do not bunch up the cord or wrap it

around the receiver. For best reception, the cord should hang as straight as possible.

7. Clip the receiver onto a belt or waistband, or slip it into a pocket (see Belt Clip Installation, page

10).

8. Check that the “FM Indicator” is illuminated yellow. Turn the “On/Off/FM Volume” knob to adjust the

volume to a comfortable listening level.

IMPORTANT: Make sure the receiver is turned OFF when not in use. Turn the “FM Volume” knob

completely counter-clockwise. It should “click” and the “Power On” indicator should turn off.

ADJUSTING THE R36 VOLUME CONTROLS:

A. Adjust the left control, “On/Off/FM Volume”, to a comfortable listening level. Check that the

“FM Indicator” is illuminated yellow. Turn the volume knob clockwise until you are able to

hear audio from the transmitter.

B. Adjust the right control, “Mic”, volume second, turning it clockwise until you can hear

sounds picked up by the plug mount microphone.

C. Adjust the “Mic” and “On/Off/FM Volume” controls for a comfortable mix of FM and ambient

sounds.

Andere Handbücher für Transmitter T36

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Williams Sound Hörgerät Handbücher

Williams Sound

Williams Sound Neckloop Bedienungsanleitung

Williams Sound

Williams Sound HEARING HELPER PFM 300 Bedienungsanleitung

Williams Sound

Williams Sound Personal FM PFM 863 Leitfaden

Williams Sound

Williams Sound POCKETALKER ULTRA Bedienungsanleitung

Williams Sound

Williams Sound One 2 One TGS 100 Bedienungsanleitung

Williams Sound

Williams Sound SoundPlus WIR 237 Bedienungsanleitung

Williams Sound

Williams Sound SoundPlus WIR TX238 Bedienungsanleitung

Williams Sound

Williams Sound Sound Plus WIR TX925 Fehlerbehebungshandbuch

Williams Sound

Williams Sound Personal FM PFM 863 Bedienungsanleitung

Williams Sound

Williams Sound FM+ Series Bedienungsanleitung

Williams Sound

Williams Sound PPA 250 Bedienungsanleitung

Williams Sound

Williams Sound PPA VPE Bedienungsanleitung

Williams Sound

Williams Sound HEARING HELPER PFM 300 Bedienungsanleitung

Williams Sound

Williams Sound HEARING HELPER PFM 300 Bedienungsanleitung

Williams Sound

Williams Sound Pocketalker II Bedienungsanleitung

Williams Sound

Williams Sound PPA 275 Bedienungsanleitung

Williams Sound

Williams Sound Personal PA PPA 375 Bedienungsanleitung

Williams Sound

Williams Sound One 2 One TGS 100 Leitfaden

Williams Sound

Williams Sound PERSONAL PA System 500 Fehlerbehebungshandbuch

Williams Sound

Williams Sound PPA VP Bedienungsanleitung

Williams Sound

Williams Sound SoundPlus WIR 952 Bedienungsanleitung

Williams Sound

Williams Sound SoundPlus Infrared System WIR TX925 Bedienungsanleitung

Williams Sound

Williams Sound SoundPlus WIR 238 Bedienungsanleitung

Williams Sound

Williams Sound IR PALS Bedienungsanleitung

Beliebte Hörgerät Handbücher anderer Marken

Sonic

Sonic Bliss miniBTE Bedienungsanleitung

Lexie

Lexie B1 Stücklistenhandbuch

Widex

Widex FM+DEX Bedienungsanleitung

Camplicomms

Camplicomms HC-200 Bedienungsanleitung

Phonak

Phonak Q90 Bedienungsanleitung

Oticon Medical

Oticon Medical Ponto SoundConnector Bedienungsanleitung

Siemens

Siemens Life micon Bedienungsanleitung

Starkey

Starkey Destiny Bedienungsanleitung

Audicus

Audicus The Icon Bedienungsanleitung

Advanced Bionics

Advanced Bionics Slim HP Standard Bedienungsanleitung

Widex

Widex DREAM440 THE DREAM SERIES Bedienungsanleitung

Phonak

Phonak myPilot Bedienungsanleitung

NIKEN

NIKEN NK-401 Bedienungsanleitung

ON Semiconductor

ON Semiconductor Ezairo 7111 Pre Suite Bedienungsanleitung

Sonetik

Sonetik GOHEAR Bedienungsanleitung

Widex

Widex FL-9 Bedienungsanleitung

Siemens

Siemens MUSIC Pro Pro IT Bedienungsanleitung

Panasonic

Panasonic WH-216KZ Montageanleitung