Williams Sound WIR TX75/b Bedienungsanleitung

WIR TX75/b

Two-Channel Infrared Transmitter

MAN 166C

Manual and User Guide

WIR TX75 Two-Channel Infrared Transmitter

MAN 166C

Contents

Important Safety Instructions.................................................................................................................................................. 3

CAT-5e Cable Safety ........................................................................................................................................................ 3

Receiver Safety Warnings....................................................................................................................................................... 3

Hearing Safety ................................................................................................................................................................. 3

Battery Safety and Disposal ............................................................................................................................................. 3

Pacemaker Safety ............................................................................................................................................................ 3

Transmitter Safety Warnings............................................................................................................................................. 3

Recycling Instructions ...................................................................................................................................................... 4

System Overview.................................................................................................................................................................... 5

Installation Procedures ........................................................................................................................................................... 6

Determine Coverage Area ................................................................................................................................................ 6

Optional WIR TX75-S Slave Emitter for Additional Coverage............................................................................................. 7

Control Panel ................................................................................................................................................................... 9

Connect Power .............................................................................................................................................................. 10

Connect Audio Source ................................................................................................................................................... 10

Adjust the Audio Level.................................................................................................................................................... 10

Connecting Master and Slave Units................................................................................................................................ 11

WIR TX75 Indicators.......................................................................................................................................................12

Mounting Options ................................................................................................................................................................. 12

Accessories .......................................................................................................................................................................... 12

Troubleshooting .................................................................................................................................................................... 13

Optional Receivers................................................................................................................................................................ 14

Limited Warranty................................................................................................................................................................... 15

SoundPlus® Infrared Transmitter Specications Model WIR TX75 ........................................................................................ 16

SoundPlus® Infrared Transmitter Specications Model WIR TX75-S..................................................................................... 17

WIR TX75 Two-Channel Infrared Transmitter

MAN 166C

Important Safety Instructions

Please read and keep these instructions.

CAT-5eCABLE SAFETY

CAUTION!

Do NOT plug the WIR TX75 (master) CAT-5e / RJ45 cable into anything other than the WIR TX75-S slave(s). The TX75

CAT-5e / RJ45 connection is proprietary and is NOT compatible with ethernet or any other RJ45 systems. Failure to

comply with this caution can destroy this or other equipment and will void the warranty.

Receiver Safety Warnings

HEARING SAFETY

CAUTION!

Many Williams Sound receivers are designed to amplify sounds to a high volume level, which could potentially cause hearing

damage if used improperly. To protect your hearing and the hearing of others:

1. Make sure the volume is turned down before putting on the earphone or headphone—only then adjust the volume to a

comfortable level.

2. Set the volume level at the minimum setting that you need to hear.

3. If you experience feedback (a squealing or howling sound), reduce the volume setting and move the microphone away from the

earphone or headphone.

4. Do not allow children or other unauthorized persons access to this product.

BATTERY SAFETY AND DISPOSAL

CAUTION!

Williams Sound receivers are supplied with non-rechargeable alkaline batteries. Do not attempt to recharge non-rechargeable

batteries; they may explode, release dangerous chemicals, cause burns, or cause other serious harm to the user or product.

PACEMAKER SAFETY

CAUTION!

If you have a pacemaker or other medical device, make sure that you are using the Williams Sound receiver in accordance with

safety guidelines established by your physician or the pacemaker/medical device manufacturer.

Transmitter Safety Warnings

WARNING! To reduce the risk of re or electric shock, do not expose the system to rain or moisture. Do not use this

apparatus near water. The system should not be exposed to dripping or splashing, and objects lled with liquids such

as beverages should not be placed on the transmitter or receivers. Clean only with a dry cloth.

CAUTION

RISK OF ELECTRICAL SHOCK — DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO

NOT REMOVE COVER (OR SIDES). NO USER-SERVICABLE

PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.

!AVIS

RIQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR

ATTENTION: POUR RÉDUIRE LE RISQUE DE DÉCHARGE ÉLECTRIQUE, NE

RETIREZ PAS LE COUVERCLE (OU CÔTÉS). IL NE SE TROUVE AL’INTÉRIEUR

AUCUNE PIECE POUVANT ETRE RÉPARÉE PAR L’USAGER. S’A DRESSER A

UN RÉPARATEUR COMPÉTENT.

WIR TX75 Two-Channel Infrared Transmitter

MAN 166C

Servicing or attempting to service this device will void the warranty

Refer servicing to qualied personnel. Servicing is required when the system has been damaged in any way: if liquid has been

spilled or objects have fallen into the unit, if the unit has been exposed to moisture, if the unit does not operate normally, or if the

unit has been dropped.

Do not block any ventilation openings. Install in accordance with manufacturer’s instructions.

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus that produces heat.

Use only attachments/accessories specied by the manufacturer.

Unplug the transmitter during lightning storms or when unused for long periods of time.

Be advised that different operating voltages require the use of different types of line cord and attachment plugs. Check the voltage

in your area and use the correct type.

Use only the power supply provided by Williams Sound. Other power supplies may have similar specications, but may not

be equivalent in emissions ratings, in-rush current, etc. Use of an unapproved power supply may leave the device partially or

completely inoperable, and will void the warranty.

This apparatus has been designed with class-1 construction and must be connected to a main socket outlet with a protective

ground connection (the third grounding prong).

Protect the power cord from being walked on or pinched, particularly at plugs, receptacles, and near the power jack on the

transmitter.

This apparatus must be grounded.

The MAINS plug or an appliance coupler is used as the disconnect device, so the disconnect device should remain readily

operable.

For Customers in The United States

WARNING: Use a three-wire grounding-type line cord as is supplied with the product. Do not defeat the safety

purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A

grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for

your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete

outlet. This equipment has been tested and found to comply with the limits for Class B digital device, pursuant to part

15 of the FCC rules.

For Customers in Canada

This Class B digital device meets all requirements of the Canadian Interference-causing Equipment Regulations.

Cet appareil numérique de la classe B respecte toutes les exigencies du Règlement sur le matériel brouilleur du Canada.

Recycling Instructions

Help Williams Sound protect the environment. Please take the time to dispose of your equipment properly.

Product Recycling for Customers in the European Union:

Please do NOT dispose of your Williams Sound equipment in the household trash. Take the equipment to a electronics

recycling center, or return the product to the factory for proper disposal.

WIR TX75 Two-Channel Infrared Transmitter

MAN 166C

System Overview

The WIR TX75 two-channel infrared transmitter combines infrared modulator and emitter technology into a single mountable

enclosure—which reduces operating costs, eliminates the need for rack space and eases set-up.

The WIR TX75 is ideal for high-quality audio programs such as music, theater and audio description. The WIR TX75 will accept

any line level, balanced or unbalanced audio inputs. Infrared receivers detect the transmission and convert the light signals back

into audio signals. The 2.3/2.8 MHz (or 3.3/3.8 MHz for TX75b) operating frequencies minimize high-efciency lighting interference.

Up to two slave emitters can be added for additional coverage. Power, baseband, and digital data are fed to the slave emitters via

a single CAT-5e cable for each emitter. No additional cables are required.

No FCC license or radio approval is required with this equipment. It can be used anywhere in the world.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15

of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the

equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to

radio communications. Operation of this equipment in a residential area may cause interference in which case the user

will be required to correct the interference at his own expense.

NOTE: A PLASMA MONITOR OR TELEVISION CAN DEGRADE THE AUDIO QUALITY OF THE WIR TX75 TRANSMITTER. FOR

BEST PERFORMANCE, THE TRANSMITTER SHOULD BE POSITIONED AS FAR AWAY AS POSSIBLE FROM ANY

PLASMA MONITOR OR TELEVISION.

WIR TX75 Two-Channel Infrared Transmitter

MAN 166C

Installation Procedures

Determine Coverage Area

When using the WIR TX75 transmitter in single-channel mode with the RX22-4 receiver, the system coverage area will exceed

5000 ft² (185 m²). WIR TX75 units automatically adjust to give the best coverage area possible in both 1-channel and 2-channel

modes.

Figure 1 illustrates typical coverage pattern for the TX75. This can be affected by direct/indirect sunlight, reections on walls and

room construction.

Reections of the infrared light from walls, ceilings, and oors may change these patterns.

Important: Remember to point the transmitter towards the listening audience.

Remember: Most objects block infrared light. The transmitter cannot be concealed behind walls, glass, curtains, etc.

These patterns are the direct radiation pattern. The infrared radiation does not drop to zero outside the illustrated patterns; it

decreases. It still may be useable at a greater distance, depending on the receiver sensitivity and the reective characteristics of

the room. Reections of the infrared light from walls, ceilings, and oors may change these patterns.

The TX75 and TX75-S can be operated with or without the faceplate, if desired. The faceplate can be removed and painted to

match room decor. Lightly sand faceplate with 400 grit sandpaper apply primer and two coats of nal color. Do not paint the

infrared lens behind the faceplate of the TX75.

Figure 1: Receiver coverage area with WIR TX75 transmitter OR WIR TX75-S slave emitter in single channel mode.

RX22-4 RECEIVER

RX18 RECEIVER RX15-2 RECEIVER

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170

A157

FEET

WIR TX75 Two-Channel Infrared Transmitter

MAN 166C

Optional WIR TX75-S Emitter for Additional Coverage

For larger facilities, additional emitters can be used to increase the total coverage area. The WIR TX75 is capable of driving two

WIR TX75-S slave emitters. Power, baseband and digital data bus are fed via CAT-5e cable to each TX75-S slave.

Figure 2: overlapping illumination patterns to cover larger listening areas.

A158

Figure 3: coverage area with second emitter added to same emission point (50% increase)

0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 210 220

A156

230

FEET

MASTER ONLY MASTER + SLAVE

WIR TX75 Two-Channel Infrared Transmitter

MAN 166C

Figure 5: WIR TX75 master and two slaves at an angle of 35° to each other.

80100

120

140160

180 A159

Control Panel

Figure 6: WIR TX75 master rear view

POWER IN MIC CHANNEL

SELECTOR

LINE IN BALANCED/

UNBALANCED SELECTOR

TX75 BUS

OUT TO

SLAVE (1)

TX75 BUS

OUT TO

SLAVE (2)

MIC IN

CH 1 AUDIO

LEVEL INDICATOR

(YELLOW)

CH 2 AUDIO

LEVEL INDICATOR

(YELLOW)

SLAVE TRANSMIT

POWER INDICATOR

(YELLOW)

SLAVE POWER

INDICATOR

(GREEN)

INDICATOR

LIGHTS (ON/OFF)

MIC

ADJUSTMENT

POWER

INDICATOR

A139

RCA IN RCA IN

(2.3) TX-75 (2.8)

(3.3) TX-75b (3.8)

WIR TX75 Two-Channel Infrared Transmitter

MAN 166C

Connect Power

WARNING: MAINS VOLTAGE MUST NOT FALL BELOW 100VAC, 0R SYSTEM PERFORMANCE WILL BE

GREATLY REDUCED. UNIT MAY ENTER RESET MODE UNTIL POWER IS RESTORED.

1. Plug the power supply output cord into “Power In” on the WIR TX75.

2. Attach a line cord to the power supply.

3. Plug the power supply into the AC outlet. TFP 046: 100-240 VAC IN, 50 / 60 Hz.

This system is designed for class 2, low-voltage wiring. Always follow local electrical codes when using low-voltage wiring.

Green Power

The WIR TX75 is equipped with a sleep/power save feature. If no audio is present on either channel for three minutes, the

transmitter will automatically go into sleep/power save mode. This mode decreases power consumption by 80 percent. Units

will automatically start up when audio is activated. This sleep/power save feature can be disabled. Contact Williams Sound for

instructions.

On power up, the WIR TX75 performs a self-test to detect damage due to shipping, handling, tampering or incorrect operation.

If any failure is present, green indicator lights will blink. See WIR TX75 Indicators table on page 12 for instructions on how to read

indicator lights.

Connect Audio Source

Automatic Channel Detection/ Shutdown

The WIR TX75 offers two carrier frequencies: Ch 1 (2.3 MHz) and Ch 2 (2.8 MHz). The WIR TX75boffers two different carrier

frequencies: Ch 1 (3.3 MHz) and Ch 2 (3.8 MHz). Either unit automatically detects the presence of audio on the microphone and RCA

audio inputs, and transmits on either/both channels when an audio signal is present on that channel. If audio is present on both the

microphone and RCA jack for a given channel, the audio signals will be mixed.

When no audio signal is present on a channel for three minutes, the TX75 will shut down that channel. Operating the WIR TX75 in single-

channel mode provides a 40 percent increase in range over two-channel mode.

Line Level Source:

The WIR TX75 will accept line level, balanced or unbalanced audio inputs. Select the frequency(ies) you wish to transmit on and

connect your audio source(s) to the appropriate jack(s). If your audio inputs are balanced, use the switch to select “bal”. If your

audio inputs are unbalanced, use the switch to select “unbal”. See gure 7 for balanced wiring conguration.

Microphone Source

Plug an electret microphone into the 3.5mm “Mic In” jack (MIC 027, MIC 100, or MIC 090). To assign the microphone to Ch 1

use the Mic Channel Switch to select “2.3” (or “3.3” MHz on the TX-75b). To assign the microphone to Ch 2 use the Mic Channel

Switch to select “2.8” (or “3.8” MHz on the TX-75b).

Figure 7: Balanced line out (XLR) to WIR TX75 line input (RCA) cable

1 23

FEMALE XLR

RED (IN PHASE)

RED RCA

(TIP=IN PHASE)

2 CONDUCTOR

WITH SHIELD

BLACK (SIGNAL)

BLACK

TO TX75

SHIELD NOT CONNECTED

ON TX75 CABLE END

1= SHIELD, 2= RED (SIGNAL IN PHASE), 3=BLACK (SIGNAL)

A160

WIR TX75 Two-Channel Infrared Transmitter

MAN 166C

Adjust the Audio Level

Line Level Source

After an audio signal has been connected to the transmitter, adjust the audio source gain until the WIR TX75 audio-level indicator

for that channel blinks periodically.

Microphone Source

Speak into the microphone from a normal distance and at a natural voice level. Use the microphone gain adjustment on the TX75

to set the gain to the point where the audio level indicator on the selected channel blinks periodically. If the audio level indicator is

always on or on most of the time, the level is too high. If the audio level indicator is never on, the level is too low.

Connecting Master and Slave Units

Connect all WIR TX75 master and slave(s) units together using CAT-5e cables, the “to slave” jacks on the master, and the “Master

In” jack on the slave(s). For systems with no slave units, the CAT-5e cables and “to slave” jacks are not used. For systems with one

slave unit, either “out 1” or “out 2” may be used.

When a cable is plugged into a “to slave” jack, the master unit will automatically detect mis-wired, intermittent or bad CAT-5e

cables; a yellow status indicator light will blink on that channel’s “to slave” jack to indicate any problem. See WIR TX75 Indicators

table on page 12 for instructions on how to read indicator lights.

The WIR TX75 automatically detects when slave units are plugged in, establishes a data link to verify operation, monitors status,

and enables baseband output to the slave emitter(s).

Once a master and slave unit are connected, the yellow and green indicators located on the “to slave” and “Master In” jacks mimic

each other. This allows the user to know the status of the entire system by simply looking at the indicators on the back of the

master unit. A switch is provided to turn off all indicator lights AFTER initial set-up, to allow for less conspicuous operation.

Note: The WIR TX75 will automatically detect and adjust for differences in CAT-5e cable length. Matching cable lengths to the

slaves is not necessary. Cable length up to 100 feet may be used.

Figure 8: Connecting a WIR TX75 transmitter to two WIR TX75-S slave emitters

POWER

RCAMIC CAT5E

TX75 MASTER

TX75S SLAVE #1

(OPTIONAL)

AUDIO

SOURCE

MICROPHONE

(ELECTRET)

AC POWER

SOURCE

TX75S SLAVE #2

(OPTIONAL)

A161

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Williams Sound Sender Handbücher

Williams Sound

Williams Sound Hearing Helper T800 Leitfaden

Williams Sound

Williams Sound WIR TX7 Bedienungsanleitung

Williams Sound

Williams Sound WIR TX90 Bedienungsanleitung

Williams Sound

Williams Sound PPA T46 Montageanleitung

Williams Sound

Williams Sound WIR TX90 Bedienungsanleitung

Williams Sound

Williams Sound WIR TX75 C Bedienungsanleitung

Williams Sound

Williams Sound IR T2 Bedienungsanleitung

Williams Sound

Williams Sound PPA T46 Bedienerhandbuch

Williams Sound

Williams Sound Personal PA PPA T36 Bedienungsanleitung

Williams Sound

Williams Sound Hearing Helper T800 Bedienungsanleitung

Williams Sound

Williams Sound Personal PA PPA T36 Leitfaden

Williams Sound

Williams Sound T2800 Bedienungsanleitung

Williams Sound

Williams Sound Hearing Helper T800 Leitfaden

Williams Sound

Williams Sound WIR TX90 Bedienungsanleitung

Williams Sound

Williams Sound T4 Bedienungsanleitung

Williams Sound

Williams Sound WIR TX75-S Bedienungsanleitung

Williams Sound

Williams Sound PPA T46 Bedienungsanleitung

Williams Sound

Williams Sound Hearing Helpe T863 Montageanleitung

Williams Sound

Williams Sound WIR TX90 Fehlerbehebungshandbuch

Williams Sound

Williams Sound WIR TX75 PRO Bedienungsanleitung

Williams Sound

Williams Sound IR T01 Bedienungsanleitung

Williams Sound

Williams Sound PERSONAL PA T35 Leitfaden

Williams Sound

Williams Sound IR+ M1 Bedienungsanleitung

Williams Sound

Williams Sound PERSONAL PA T35 Leitfaden

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung