Winco HPS9000VE/E Bedienungsanleitung

113256-00 64854-005I

INSTALLATION INSTRUCTIONS

LOW PRESSURE FUEL SOLENOID KIT

FOR MODELS:

HPS6000HE/I, HPS9000VE/E

** For older version HPS gen-set instruction sheets go to

www.wincogen.com/service support/winco downloads/portable generators. **

COMPONENT LIST

REF. # PART # DESCRIPTION QTY.

1 42942-000 Gas Solenoid Valve 1

2 64856-006 Control Box Assembly 1

3 48039-006 Nylon Clamp 2*

4 97391-003 Tube Clamp 3**

5 479-000 Lock Washer 2

6 466-000 1/4” X 20 X 3/4” Bolt 3

7 54074-006 Pipe Nipple 1

8 49975-011 Cable Tie 3

* Not used on HPS6000HE/I and HPS9000VE/E models

** Used on HPS models prior to 2013.

213256-00 64854-005I

Install control box assembly (ref. 2) onto the frame of the gen-set (battery side) us-

ing 2 bolts (ref. 6) and lock washers (ref. 5).

Tighten with a 1/2” end wrench.

Run the cord to the rear of the generator and plug into one of the receptacles.

•

STEP 1

STEP 2 HPS6000HE/I

Thread the pipe nipple (ref. 7) onto the 90° elbow using pipe sealant.

Thread the gas solenoid valve (ref. 1) onto the pipe nipple using pipe sealant.

Make sure the solenoid end marked “OUT” is toward the generator and the

solenoid end marked “IN” is toward the supply line.

Tighten with a pipe wrench.

Connect wires labeled 1 & 21 from control box harness to the solenoid. Polarity

does not matter.

•

313256-00 64854-005I

Remove the bolt (A) holding the demand regulator down and rotate the demand

regulator. This allows for turning of the pipe nipple and solenoid.

Thread the pipe nipple (ref. 7) onto the 90° elbow using pipe sealant.

Thread the gas solenoid valve (ref. 1) onto the pipe nipple using pipe sealant.

Make sure the solenoid end marked “OUT” is toward the generator and the

solenoid end marked “IN” is toward the supply line.

Tighten with a pipe wrench.

Replace demand regulator bolt.

Connect wires labeled 1 & 21 from control box harness to the solenoid. Polarity

does not matter.

•

STEP 2 HPS9000VE/E

STEP 3 HPS6000HE/I

Take battery positive cable loose from starter solenoid (A). Route RED wire # 2

through the rubber cable protector (B) and re-tighten starter solenoid nut (C).

Take battery negative cable loose from engine base (D). Place BLACK wire # 1

under the bolt and re-attach battery negative cable to engine base.

•

413256-00 64854-005I

STEP 4

Using the cable ties (ref. 8) provided, neatly tie excess wire loom, wire and power

cable to prevent rubbing on the engine. HPS9000VE/E shown below.

TO START: Hold down control box button, turn key, engine will start. Once unit

generates power (about 1 second) release button.

•

Winco Inc.

Service Dept.

507-357-6831

STEP 3 HPS9000VE/E

Take battery positive cable loose from starter solenoid (A). Route RED wire # 2

through the rubber cable protector (B) and re-tighten starter solenoid nut (C).

Take battery negative cable loose from engine base (D). Place BLACK wire # 1

under the bolt and re-attach battery negative cable to engine base.

•

Andere Handbücher für HPS9000VE/E

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Winco Tragbarer Generator Handbücher

Winco

Winco DR20I4 Einrichtungshandbuch

Winco

Winco DP5000-03/A Einrichtungshandbuch

Winco

Winco ULPSS15B2W Einrichtungshandbuch

Winco

Winco 700-11 Bedienungsanleitung

Winco

Winco WL16000HE-03/A Administratorhandbuch

Winco

Winco HPS12000HE/F Einrichtungshandbuch

Winco

Winco PSS21/E Einrichtungshandbuch

Winco

Winco HPS6000HE/I Einrichtungshandbuch

Winco

Winco 55PTOC4-18/1 Administratorhandbuch

Winco

Winco DP7500/B Einrichtungshandbuch

Winco

Winco PSS8B2W Administratorhandbuch

Winco

Winco WC10000VE-G Einrichtungshandbuch

Winco

Winco DR35F4/1 Administratorhandbuch

Winco

Winco RP50 Administratorhandbuch

Winco

Winco CSAW6010DEX/C Bedienungsanleitung

Winco

Winco PSS20000/E Einrichtungshandbuch

Winco

Winco PSS20000LS Bedienungsanleitung

Winco

Winco HPS12000HE-03/B Einrichtungshandbuch

Winco

Winco ULPSS8B2W Einrichtungshandbuch

Winco

Winco WL18000-B Bedienungsanleitung

Winco

Winco Home power HPS12000HE Einrichtungshandbuch

Winco

Winco DP14000VE-03/A Einrichtungshandbuch

Winco

Winco PSS60B Bedienungsanleitung

Winco

Winco WL22000VE Administratorhandbuch

Beliebte Tragbarer Generator Handbücher anderer Marken

Kohler

Kohler 20EORZ Bedienungsanleitung

Powerhorse

Powerhorse 83171 Bedienungsanleitung

HURST

HURST ML-630-SI Bedienungsanleitung

ETQ

ETQ TG4000 Bedienungsanleitung

Briggs & Stratton

Briggs & Stratton 40265 Einrichtungshandbuch

ConMed

ConMed 7550 Bedienungsanleitung

Owon

Owon Waveform Generator Bedienungsanleitung

evertz

evertz 7700 Series Bedienungsanleitung

Power Stroke

Power Stroke PS906025 Bedienungsanleitung

Firefly

Firefly Cygnus CYG2400/460/24 Bedienungsanleitung

Draper

Draper PG950S Firmware-Update

PowerBoss

PowerBoss PowerBoss Bedienungsanleitung

SDMO

SDMO SH 4000 Bedienungsanleitung

EINHELL

EINHELL STE 5500 Bedienungsanleitung

Wanco

Wanco WI3000P Bedienungsanleitung

Full Boar

Full Boar FBT-3300 Bedienungsanleitung

Dwyer Instruments

Dwyer Instruments ASG Bedienungsanleitung

Westinghouse

Westinghouse WH1000i Series Bedienungsanleitung