Winegard Movin' View MV-0500 Bedienungsanleitung

Movin’ViewTM

Automatic Digital Satellite Mobile Antenna

ModelMV-0500

Made in the U.S.A.

Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000

319/754-0600 • FAX 319/754-0787 • www.winegard.com

Printed in U.S.A. © Winegard Company 2002 2451018

WINEGARD®

DIRECTV®is an official trademark of DIRECTV, a unit of GM Hughes Electronics Corporation.

DISH NetworkTM is an official trademark of EchoStar Communications Corporaton.

DIGITAL BROADCAST SYSTEM

SATELLITE(S)

Introduction

Congratulations! You have purchased one of

Winegard’s latest developments in the mobile satel-

lite reception product line —the Movin’ViewTM.

This system, used with your digital satellite receiver,

will deliver the best reception possible using GPS

(Global Positioning System) and precision gyro-

scopes.

How Does Digital Satellite

TVWork?

Satellite programming originates from an “uplink”

facility on Earth — the facility receives many signals

from different sources, combines the signals digitally

and transmits to the satellites. The satellites (22,300

miles above Earth) receive the uplink signal, amplify

it and then transmit it back to earth in the

Ku frequency band. This signal

is concentrated and reflected to

the LNBF* located at the “focal

point” of the dish. The LNBF

amplifies and converts the signal to

the 950 to 2050 MHz range. The signal

is then passed through a coaxial cable

to the receiver where individual chan-

nel selection and processing take

place.

For Programming information call:

DISH NETWORKTM - 1-800-333-DISH (1-800-333-3474)

DIRECTV®- 1-800-DIRECTV (1-800-347-3288)

ExpressVu TM 1-888-SKY-DISH (1-888-759-3474)

Your new Winegard RV Digital Satellite System is an easy-

Introduction/How Does Digital Satellite TV Work?

PROGRAMMING UPLINK

CONTROL CENTERS

HIGH POWER KU-BAND

DOWNLINK SIGNAL

WINEGARD DIGITAL SATELLITE

SYSTEM ANTENNA

RECEIVER

UPLINK SIGNAL TELEVISION

SET

to-use satellite TV reception system. Because it mounts

on the top of your recreational vehicle, it goes where you

go and provides quality reception of digital satellite sig-

nal in the continental United States only.

* Low Noise Block Converter Feed

1 Cable entry plate

1 large yellow spade connector

2 small red spade connectors

All required screws and washers

1 base with electronics, dish, dual LNBF

1 tube silicone

1. Open box and remove packing material.

2. Lift unit out of box vertically. Do not turn box and

“roll” out, or turn upside down to remove.

USE 2 PEOPLE

when removing the unit

from the carton.

Parts Included • Tools Needed • How to Unpack

If using knife to open

carton, BE CAREFUL.

Do not cut the dome on

the unit.

About this manual —

We hope this manual will provide clear instructions to install and operate the MV-0500.

Two symbols have been used —

!Indicates caution should be taken! Indicates suggestions to make

processes easier for you.

PARTSINCLUDED:

1 Radome

3 base mounting feet

1 Power switch

2 Wall plates (white & brown)

1 Surface mount bracket

2 Cable clamps

LIFT UNIT STRAIGHT UP

TOOLSNEEDEDFOR UNPACKING & INSTALLATION:

UNPACKINGTHEUNIT

7/16” open end wrench

Level

Drill w/3/4” bit

1-1/4” hole saw (if mounting switch in wall)

5/16” Socket for roof screws

1/8” Allen wrench

1/2” Open end wrench

Crimping tool for coax connections

Crimping tool for electrical connections

Small blade screw driver

Pliers

Sealant (consult RV manufacturer for proper type for

your roof material)

Installation Diagram

BACK OF

VEHICLE

FRONT OF VEHICLE

GPS ANTENNA

ADJUSTABLE

BASE FOOT

ADJUSTABLE

BASE FOOT

REAR BASEFOOT

MUST DIRECTLY

FACE REAR OF

VEHICLE

LEVELING

SCREW

LEVELING

SCREW

LEVELING

SCREW

CONTROL

UNIT

POWER

SUPPLY

REFLECTOR

HEYCO®

CONNECTORS

FIGURE 1

6. On each foot, screw the flange nut to the base of

the leveling screw on the mounting foot, flange up.

Place rubber washer, with the rubber side up, on

the nut, Figure 2. Push mounting foot under base.

Push foot screw through the base and tighten lock

nut to secure foot to base. Be sure the base feet are

pointing away from the base. Base feet will be re-

moved later during install.

Installation

Install in DRY conditions only!

If you have trouble seeing the numbers,

try using a magnifying glass!

FIGURE 2

FIGURE 3

OBSTRUCTION

UNIT BASE

Installing unit on roof of vehicle —

5. Determine which programming you will be using.

This will determine how you set your switches.

For DISH NetworkTM set

switches to 119°.

For DIRECTV®set switches to 101°.

For ExpressVuTM set switches 092°.

LEVELING SCREW

RUBBER WASHER

FLANGE NUT

(FLANGE UP)

Obstruction Ht. Unit Clearance

8” ..........................................4”

10” ................................... 11.5”

12” ...................................... 19”

15” ...................................... 32”

IMPORTANT! Do not install this system

in the rain, or under any wet conditions. Moisture

may affect electronics and void your warranty!

1. For best performance and to reduce signal acquisi-

tion time, park vehicle on a level surface.

2. Select a level spot on your roof for installation.

• The unit should be no more than +/-1° off level.

• Be sure no roof-mounted equipment is

blocking the satellite “line of sight.”

• You will need to decide where the wires will enter

the vehicle. A coax and an 18 gauge power wire

will need to be placed in the vehicle. The power

wire will go to the nearest +12 VDC power source;

the coax will be routed through the demulitplexer to

your satellite receiver. These wires should be hidden.

3. Remove screws holding dome to base and remove

dome. Place dome in safe spot to avoid damage. Place

base on vehicle roof in the location selected.

4. Remove wire ties used for shipping. There are

three; one on each side of the reflector and one at the

the rear of the reflector holding down the counter-

weight. See Figure 1, page 4.

MOUNTING

FOOT

7. After selecting location for unit (see step 2),

put the unit on the centerline of the coach.

REAR MOUNTING FOOT MUST FACE

DIRECTLY OFF REAR OF VEHICLE,

Figure 1. There is a 30 foot power cord and 30

foot coax cable going through the Heyco®con-

nectors on the base.

Placing the rear base bracket on the centerline,

facing the rear of the vehicle, will center the unit.

8. Using the chart,

determine the

minimum distances to

other equipment.

Measure these

distances as

demonstrated in Figure 3.

123456789012345678901234567890121

2345678901234567890123456789012

123456789012345678901234567890121

10. Clean roof area where the base feet will be

attached to the roof. Do not erase your marks!

11. Put approved sealant in the area under the base

feet. Place base foot on top of the sealant and

screw down using (2) #10 screws (provided) for

each base foot.

12. Unscrew the locknuts in the base and remove

the base from feet. Put the other (4) #10 screws

into the roof through the remaining holes in the

base feet.

Installation

ROOF INSTALLATION, continued

9. Place the unit on the roof in its permanent location

and mark around the base bracket, Figure 4. (Make

sure the rear adjustable base foot is directly facing

the back of the coach.)

FIGURE 4

FIGURE 5

The GPS antenna is pre-wired and has a 3 foot cable

running through one of the Heyco®connectors.

When deciding where to place GPS antenna, DO

NOT SECURE! After wiring the receiver and initializ-

ing your system, you will need to test the system

(“Initializing and replacing dome” on page 8).

Determine location for GPS antenna. It is recom-

mended you place the GPS antenna between unit base

and side edge of vehicle, 90° from rear mounting

bracket, Figure 6.

The recommended location for the GPS antenna is

based on having a level location and a clear view of

the sky. If another location, further from the base, is

desired, loosen the Heyco connector and pull out addi-

tional wire in the base. You must re-wrap and re-tie

the GPS cable inside the dome to prevent interfer-

ence with the LNBF. Failure to do so will result in

malfunction! Tighten Heyco connectors when done.

IMPORTANT! The GPS must be located away from

obstructions on roof of vehicle and other obstructions

such as trees, tall buildings, etc. You must have a

clear view of the sky for proper operation.

GPS installation —

FIGURE 6

13. After all base brackets are secured to roof, put

sealant on top of foot and screws. Place base on level-

ing screws located on base feet and install nut and

rubber washer on leveling screw.

14. Leveling the base is done by tightening or loosen-

ing the flange nut under the base, Figure 5.

Use an electronic level to adjust base so there is no

more than +/- 1° off level in all directions. Place

level on base of unit if possible. (If your level will not

fit inside the base plate, place on outside edge.) Level

front to back and side to side. Raise and lower by ad-

justing flange nut under base. After leveling base,

secure inside base with rubber washer, rubber side

down toward base, and lock nut.

BASE EXTERIOR

FOOT

LEVELING

SCREW/FLANGE

GPS

ANTENNA

HEYCO®

CONNECTORS

REAR BASE FOOT

MUST DIRECTLY FACE

REAR OF VEHICLE

FRONT OF VEHICLE

CABLE-

ENTRY

PLATE

CABLE CLAMP -

EVERY12”-16”

1. Decide the best location for the cables to enter the

vehicle, and the location of the switch and receiver

(see “Installing the switch and receiver” below.) Drill

a 1/2” hole in the roof, push wires inside. Make

proper connections (remember you must have fil-

tered +12 VDC power source).

2. Place cable-entry plate over hole and cables. Screw

in place. Seal plate and screw holes with approved

sealant (not included).

FIGURE 7

Cable entry installation —

3. Depending on the length of the cable on the roof,

you may need to use cable clamps or wire ties (not

provided) between the unit and your cable-entry plate.

Clamping the cable every 12”-16” should eliminate

any unnecessary cable movement, Figure 7.

Installation • Wiring

INSTALLATION

1. Decide the location of the power on/off switch.

Be sure the switch is turned off before you begin!

See diagram below.

Wall or panel mount: Drill 1-1/4” hole, pull wires

through wall or panel.

Surface mount: Determine location and direction of

box. Mount box feed wire into one of the box open

ings.

Select plate cover (brown or white provided) and snap

the rocker switch into the switch plate. Be sure switch is

off!

2. Connect +12 VDC power from vehicle, using red

spade connector, to isolated spade on switch.

3. Connect red power wire from MV-0500 using red

spade connector to center spade on switch.

4. Connect vehicle ground and black ground wire,

using yellow spade connector, to silver spade on

switch.

FILTERED

+12 VDC

FROM

VEHICLE

INSTALLINGTHEPOWERSWITCHDIAGRAM

STEP 4

STEP 3 STEP 2

TWO BLACK GROUND WIRES

1 FROM VEHICLE

1 FROM MV-0500

ON/OFF ROCKER

WITH LIGHT

(SHOWN IN OFF

POSITION.)

MV-0500

RED POWER

WIRE

FIGURE 8

Initializing & replacing the dome after

connecting the receiver(s) —

1. Be sure vehicle is in a location free of all obstruc-

tions and with a clear view of the satellite.

2. DO NOT MOVE VEHICLE during the first initial-

ization. Power up unit, turn on receiver. FOR THE

FIRST TIME ONLY, the unit may take up to 10 min-

utes to initially find the satellite signal. The GPS is

also initializing at this time. After the GPS initializes,

the unit will begin searching for the correct satellite.

3. If the GPS does not initialize at this time, turn off

the unit. You may need to move the GPS antenna to a

different location on your roof. After you move the

GPS, DO NOT SECURE TO ROOF.

4. TEST YOUR SYSTEM BEFORE SECURING

THE GPS ANTENNA. Make sure the TV/receiver

have the correct satellite.

5. After the correct satellite has been found, secure

GPS antenna by removing adhesive backing and se-

curing to roof.

6. Install dome. NOTE: After Heyco conmectors are

tightened, apply bead of silicone around the connec-

tor where the exterior hex nut touches the base and

around the cables where they enter the Heyco on the

exterior of the unit. See drawing below. If second

receiver is not used, apply silicone to seal center hole

of third Heyco. See drawing below.

8. Before inserting screws on sides of dome, apply

silicone to ENTIRE oval slot in gasket AND to screw

threads, then insert screws and tighten. See drawing.

Connecting two receivers

1. Connect the coax cable coming from the MV-0500

to the “ SATELLITE IN” input on the primary re-

ceiver. The primary receiver is the reciever used most

often.

2. Run a second cable through the empty Heyco open-

ing and connect to the ground block-type feed through

and connect the other end of this cable to “Satellite

IN” input on the second receiver.

Installation • Wiring

Connecting one receiver

1. Connect the coax cable from the MV-0500 to the

“SATELLITE IN” on the receiver.

Connecting the receiver —

SAT RECEIVER

WIRING ONE RECEIVER

SATELLITE IN

PRIMARY

RECEIVER

USED ONLY WITH

2 RECEIVERS

GROUND BLOCK

CUSTOMER/INSTALLER

PROVIDES COAX

SAT RECEIVER

WIRING TWO RECEIVERS

SATELLITE IN

SAT RECEIVER

FILL OVAL

WITH SILICONE FILL SCREW THREADS

WITH SILICONE

BEFORE INSERTING

HEYCO CONNECTOR

APPLY SILICONE BEAD IN

HOLE WHERE COAX ENTERS

APPLY SILICONE BEAD

AT BASE OF HEYCO

CONNECTOR

UNIT BASE

Operation

Yournew MV-0500 features:

• GPS technology

• Fast signal acquisition times

• Easy “one-button” operation

• Ability to toggle between satellites using

remote control, if subscribing to multi-

satellite programming

Vehicle must be parked.

1. Turn on receiver and television set. This unit

will not operate unless receiver is on. Be sure

your TV is turned to channel 3 or 4.

2. Turn your +12VDC power switch to ON posi-

tion.

3. Allow up to 3 minutes for signal location. Sat-

ellite signal acquisition will occur with normal

operating conditions.

NOTE: Acquisition time will be longer if the ve-

hicle has traveled more than 600 miles without the

unit in use. If you have traveled this distance

without using the unit, signal acquisition may

take up to five minutes.

4. If you do not have a signal after three minutes, be

sure there are no obstacles preventing signal acquisition.

(Trees, hill, buildings or other structures can block the

signal.) Move to an open area so your system can “see”

the satellite signal.

• Low maintenance

• Compatible with continental U.S. digital satel

lite receivers

• Winegard warranty

To operate your system —

To toggle between satellites when subscribing to multi-satellite programming—

The MV-0500 will toggle between two different

satellites. Both DIRECTV and DISH Network

have programming on more than one satellite.

When a channel is selected on the remote control

and it is not located on the satellite the unit is

currently on, the system on the vehicle will auto-

matically move to the new satellite.

DIRECTV programming

1. There is NO SETUP required for DIRECTV.

When you request a channel located on a differ-

ent satellite, the unit will automatically move to

that satellite.

DISH Network programming

NOTE: This must be a DISH 500 system. These steps

must be done each time the receiver loses 110 VAC

power.

1. Let unit acquire the satellite signal on satellite 119.

2. After signal has been acquired, press the MENU key on

the remote control or receiver.

3. Go into the SYSTEM SETUP menu.

4. Go into the INSTALLATION menu.

5. Go into the MULTI-DISH installation.

6. Scroll down to the CHECK SWITCH button and select.

7. The receiver will verify that you want to perform a

“Check switch.” Select CHECK.

8. The receiver will begin checking your switch by tog-

gling between transponders. When this is completed, a

message stating “satellite reception is verified” will show.

When it does, select OKAY. If this message does not ap-

pear, repeat steps 1 - 7.

9. Your system is now set up to toggle between satellites.

It will automatically move to correct satellite when chan-

nel is selected.

Signal strength screen meter shows some

signal strength, but constantly moves up and

down, and is never locked on satellite.

Unit continues to move, but never finds any signal.

The unit continues to move and the signal strength

screen shows that it is finding the satellites, but will

never lock onto any satellite. Continues to search.

The unit moves around in circles, then points off

the front of the coach.

the next steps. Voltage must be +12 VDC, except at the

LNBF, see Figure 9, page 11.

6. To check voltage at connections, see Figure 9 on

page 11. FOLLOW THE NUMERICAL SEQUENCE

ON THE DRAWING AND CHECK VOLTAGE AT:

#1. Power Supply.

#2. LNBF voltage. Disconnect the coax cable from

the LNBF. Check voltage from the middle wire to

the shield. There should be +12 to +19 VDC. If no

voltage is present, make sure receiver is on and

check for +12 to +19 VDC at ends of gray coax

cable (remove at box junction).

#3. ‘Mini-cable’ connection voltage at Control Box.

#4. Coax cable at Control Box going to

Heyco connector.

7. Are the rotary dip switches in the correct position (101

or 119 or 092)?

8. If the unit still does not have a signal, power off and

power back on.

IF YOU DO NOT HAVE A SIGNAL:

1. The signal may be blocked by trees, hills or

structures. Pull into an area where no trees or

buildings are in the line of sight from unit to the

satellites.

2. Check your +12 VDC power switch. Make

sure it is in the ON position.

3. Check your connections. The receiver must

be connected to the power and coax connected

from receiver to the satellite dish.

4. Check your power supply. The +12 VDC

power supply must be hooked up. Check for +12

VDC on the roof at the connector.

5. Is the rear adjustable base bracket facing the

rear of the vehicle? See Figure 1, page 4.

6. Loss of signal may also be caused by snow on

roof of vehicle.

NOTE: The power rocker switch must be ON for

Check your power voltage. You may have dirty

power. You must have a minimum of +12 VDC.

Make sure receiver is on and connected properly.

Check rotary dip switches for correct setting. (i.e.

DISH network 119°, DIRECTV 101°, etc.).

PROBLEM SOLUTION

Be sure the switches are set on the correct numbers —

see page 5, step 5.

The GPS is not acquiring a signal.

Troubleshooting

Inhaltsverzeichnis

Andere Winegard Antenne Handbücher

Winegard

Winegard AIR 360+ Bedienungsanleitung

Winegard

Winegard AS-2003 Betriebsanleitung

Winegard

Winegard FlatWave AIR Bedienungsanleitung

Winegard

Winegard PR-8800 Bedienungsanleitung

Winegard

Winegard Movin' View MV-4002 Bedienungsanleitung

Winegard

Winegard YA-7000 Bedienungsanleitung

Winegard

Winegard HD6055P Bedienungsanleitung

Winegard

Winegard MA1000W Bedienungsanleitung

Winegard

Winegard In-Motion MVT-35W Bedienungsanleitung

Winegard

Winegard Movin' View MV-4005 Bedienungsanleitung

Winegard

Winegard TRAV'LER Series Bedienungsanleitung

Winegard

Winegard RZ-7500 Bedienungsanleitung

Winegard

Winegard DuraSAT D4 CM2000T Bedienungsanleitung

Winegard

Winegard Movin' View MV3500A Bedienungsanleitung

Winegard

Winegard TR-6018 Bedienungsanleitung

Winegard

Winegard Sensar HV CC-25HV Bedienungsanleitung

Winegard

Winegard PR-7015 Bedienungsanleitung

Winegard

Winegard Sensar HV CC-10HV Bedienungsanleitung

Winegard

Winegard Carryout G2 Bedienungsanleitung

Winegard

Winegard dish Playmaker Bedienungsanleitung

Winegard

Winegard Movin' View MV3500T Bedienungsanleitung

Winegard

Winegard HD7694 Bedienungsanleitung

Winegard

Winegard Pathway X2 Installationsanleitung

Winegard

Winegard Rayzar.Air RVRZ25W Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

IWCS

IWCS iriBelt II Einrichtungshandbuch