Winegard Movin' View MV-4002 Bedienungsanleitung

Movin’ ViewTM

Digital Satellite Mobile Antenna for Two Receivers

for Use While Stationary or In-Motion

Model MV-4002

Made in the U.S.A. U.S. Patent Nos. 6,023,247; 6,188,300

Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000

319/754-0600 • FAX 319/754-0787 • www.winegard.com

Printed in U.S.A. © Winegard Company 2005 2452062 Rev. 5/05

WINEGARD®

DIRECTV®is an official trademark of DIRECTV, a unit of GM Hughes Electronics Corporation.

DISH NetworkTM is an official trademark of EchoStar Communications Corporaton.

DIGITAL BROADCAST SYSTEM

SATELLITE(S)

Introduction

Congratulations! You have purchased one of

Winegard’s latest developments in the mobile satellite

reception product line —the Movin’ ViewTM. This sys-

tem, used with your digital satellite receiver, will

deliver the best reception possible using GPS (Global

Positioning System) and precision gyroscopes.

How Does Digital Satellite

TV Work?

Satellite programming originates from an “uplink” facil-

ity on Earth — the facility receives many signals from

different sources, combines the signals digitally and

transmits to the satellites. The satellites (22,300

miles above Earth) receive the uplink signal, amplify it

and then transmit it back to earth in

the Ku frequency band. This signal

is concentrated and reflected to the

LNBF* located at the “focal point” of

the dish. The LNBF amplifies and

converts the signal to the 950 to 1450

MHz range. The signal is then passed

through a coaxial cable to the receiver

where individual channel selection and pro-

cessing take place.

Introduction/How Does Digital Satellite TV Work?

PROGRAMMING UPLINK

CONTROL CENTERS

HIGH POWER KU-BAND

DOWNLINK SIGNAL

WINEGARD DIGITAL SATELLITE

SYSTEM ANTENNA

RECEIVER

UPLINK SIGNAL TELEVISION

SET

Your new Winegard RV Digital Satellite System is an

easy-to-use satellite TV reception system. Because it

mounts on the top of your recreational vehicle, it goes

where you go and provides quality reception of digital sat-

ellite signals. Check with your program provider for exact

coverage area.

* Low Noise Block Converter Feed

For Programming information call:

DISH NETWORK®- 1-800-333-DISH (1-800-333-3474)

DIRECTV®- 1-800-DIRECTV (1-800-347-3288)

EXPRESSVU®- 1-888-SKYDISH (1-888-759-3474)

MV-4002 features:

• GPS technology

• Easy “one-button” operation

• Compatible with most digital satellite receivers

• Ability to toggle between satellites using remote

control, if subscribing to multisatellite programming

• Winegard warranty

About this manual —We hope this manual will provide clear instructions to install and

operate MV-4002. Two symbols have been used —

Indicates caution should be taken! Indicates suggestions to make

processes easier for you.

2. Determine which programming you will be using. This will determine how you set your switches.

For DISH Network set switches to 119°. For ExpressVu®,set switches to 091°.

NOTICE!

This model is PRESET for DIRECTV®receivers.

If you have a DISH Network®or ExpressVu®(Canada) receiver,

you must change the numbered switches inside the dome.

TO CHANGE SWITCHES INSIDE DOME —

1. Remove screws holding dome to base and remove dome. Place dome in safe spot to avoid damage.

Switches will be set at 101° for DIRECTV®. You will be changing these switches.

DIRECTV®receivers must be set to the two satellite, oval dish setting. Refer to your receiver manual.

DISH Network receivers must either have the check switch set for SW42 or unknown, no satellite found. See

page 5.

The satellite system has two modes of operation; Tracking Mode and Sleep Mode. When you first turn the

unit on it enters Tracking Mode. In this mode the unit will search and actively follow the satellite as the vehicle

travels. Tracking Mode ends when the unit has successfully finished its search and the vehicle has not moved

for six minutes.

Sleep Mode, this is the unit at rest mode. During Sleep mode the dish will toggle between primary and sec-

ondary satellites as you change channels with the remote. The unit enters Sleep mode about six minutes after

a successful search if stationary, or six minutes after the vehicle stops moving.

(#1 represents Switch DOWN; #0 represents Switch up)

Sat. Rcvr. Mt. Option Switch Set Position

................................... 1 2 3 4 5 6 7 8

DIRECTV A 0 0 0 0 0 0 0 1

(FACTORY PRESET)

DIRECTV B 1 0 0 0 0 0 0 1

DISH NETWORK A 0 0 0 1 0 0 1 1

DISH NETWORK B 1 0 0 1 0 0 1 1

ExpressVu A 0 1 0 1 1 0 1 1

ExpressVu B 1 1 0 1 1 0 1 1

Models MV-4002, MV-4000, MV-4005

Quick Reference Guide

1 2 3 4 5 6 7 8

1 = DOWN

MOUNTING OPTIONS

SHOWN BELOW

MOUNTING

OPTION A

1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8

MOUNTING

OPTION A

MOUNTING

OPTION A

0= UP 1= DOWN 0= UP 1= DOWN

FIGURE 1A, OPTION A

CENTER LINE OF VEHICLE

BASE FOOT

(MUST BE PARALLEL

TO CENTER LINE)

MV-3500

BACK OF VEHICLE

FRONT OF VEHICLE

FIGURE 1B, OPTION B

MOUNT OPTIONS A AND B

CENTER LINE OF VEHICLE

BASE FOOT

(MUST BE PARALLEL

TO CENTER LINE)

MV-4002

BACK OF VEHICLE

FRONT OF VEHICLE

MV-4002

  

  

 





 

00 0 0 0 0 0 1

0= UP

00 0 10 0 11 01 0 11 01 1

Operation

1. Turn on receiver and television set. The MV-4002

must be connected to a receiver that is plugged

into 120 VAC.

2. Verify that you are getting the receiver’s menu

screens on the television. These screens are avail-

able with or without the dish finding the signal.

3. Turn the power switch on for the MV-4002.

The dish should start moving, making one or two

revolutions before it stops to acquire GPS. This can

take a few moments or up to 10 minutes. Normal

operation will be less than a minute.

4. Once the unit has acquired GPS, the dish will

begin its search.

a. The dish will pause on the signal long enough to

determine which satellite it has found.

b. If it moves off the signal , it is in an effort to verify

the signal and it should return to the signal shortly.

5. After the unit has verified that it has the correct

satellite, it will continue to fine tune for about 6 min-

utes (unless the vehicle is in-motion, see 7 below).

6. At the end of 6 minutes the unit will move to check

it’s alternate satellite then move back to the primary

and go to sleep. See page 3 for a description of

Sleep Mode.

7. While the vehicle is in motion, the unit will not en-

ter sleep mode after a successful search. Instead it

will wait until the unit has stopped moving for 6 min-

utes before entering sleep mode.

8. If you do not have signal, see Troubleshooting,

p. 11.

Recovery from Signal Interruption—

The unit must travel in straight

line for 10 seconds when starting

to operate in motion.

While traveling, the signal will be interrupted

when the line of sight to the satellite is blocked.

Signal is acquired again after line of sight is restored.

If signal is interrupted for more than 15 seconds, the

system automatically enters the search routine. The

length of time for the TV picture to recover de-

pends on the receiver model you are using.

To toggle between satellites when subscribing to multi-satellite programming—

While in Sleep Mode, the MV-4002 will toggle be-

tween the primary and seconday satellites for either

DISH Network or DIRECTV. Both have program-

ming on more than one satelite.When a channel is

selected on the remote control and is not on the

satellite currently selected, the unit will automati-

cally move to the correct satellite.

DIRECTV programming

1. DIRECTV receivers must be set for oval dish 2

sat selection to enable toggling between primary

101°W satellite and alternate 119°W satellite only.

(Consult receiver manual for procedure.) After

receiver is set for the correct dish selection, when

you request a channel located on a different satel-

lite, the unit will automatically move to that

satellite.

DISH Network programming (DISH 500)

DISH Network receivers must have the “SW42”

switch installed in order to toggle between the pri-

mary 119 satellite and the alternate 110 satellite.

(Consult your receiver manual for the procedure to

reach the “check switch” menu.)

To install the “SW42” switch:

1. Before turning on your MV-4002 system, make

sure that your satellite receiver and television are

turned on and your receiver is on the “point dish”

menu. (Consult your owner’s manual to reach this

menu.)

2. While the vehicle is stationary, turn on the MV-

4002 system and wait for signal acquisition on

satellite 119.

3. After signal is acquired, the system will continu-

ously track the signal for approximately 6 minutes.

At the end of 6 minutes, the unit will enter sleep

mode. You now have 6 minutes to complete

Check Switch test. Consult your receiver manual

for instructions on running this test. Be sure that

Superdish and Alternate are unchecked if applicable.

Onscreen options may vary by receiver.

4. During the Check Switch Test, the receiver will

begin checking the switch by toggling between

satellites. When this is completed, SW42 will ap-

pear on the screen. It will be at the top of the

screen, satellite designations will be below, show-

ing odd and even transponders. See illustration.

If a switch other than SW42 appears, or you

have an X in one of the boxes below the satel-

lites, repeat Check Switch Steps.

5. Your system is now set up to toggle between sat-

ellites. It will automatically move to the correct

satellite when a channel is selected with your remote

control.

NOTE: Once these steps are completed, you

won’t have to perform this test again, unless

Check Switch was performed on another satel-

lite dish, such as a home dish.

Check Switch screen display

Install Summary

Input: 1 1 1 1

Satellite: 119 119 110 110

Polarity: Odd Even Odd Even

Status: Satellite reception verified

Superdish Alternate

Cancel Test Help

SW42

NOTE: Be sure the “Superdish” and “Alter-

nate” boxes ARE NOT checked.

Toggle: Your Winegard Automatic

satellite dish will move from the

primary to the alternate satellite in

order to receive multi-satellite

programming.

1. Open box and remove packing material.

2. Lift unit out of box vertically. Do not turn box and

“roll” out, or turn upside down to remove.

1 large yellow spade connector

2 small red spade connectors

All required screws and washers

1 base with electronics, dish, single LNBF

30’ power cable and 30’ coaxial cable

USE 2 PEOPLE

when removing the unit

from the carton.

Parts Included • Tools Needed • How to Unpack

If using knife to open

carton, BE CAREFUL.

Do not cut the dome on

the unit.

PARTS INCLUDED:

1 Radome

1 Power switch

1 Wall plate (white)

1 Surface mount box

1 Cable entry plate

LIFT UNIT STRAIGHT UP

OUT OF CARTON!

TOOLS NEEDED FOR UNPACKING & INSTALLATION:

UNPACKING THE UNIT

Level

Drill w/3/4” bit

1-1/4” hole saw (if mounting switch in wall)

3/8” Box/Open end wrench for dome screws

7/16” Open end wrench

Phillips screw driver #2

Sealant (consult RV manufacturer for proper type

for your roof material)

!Do not paint dome!

Painting dome will cause

signal degradation.

!BE CAREFUL when

removing unit. Dome is

attached to base by

ONLY THREE PEICES

OF TAPE!

Base Diagram

FIGURE 2

CONTROL

BOX

(DETAIL

BELOW)

COAX CABLE AT

CONTROL BOX

CONTROL

BOX TO LNBF

AZ MOTOR

GPS

ANTENNA

FOOT

MUST BE

PARALLEL

TO THE

CENTER LINE

OF THE

VEHICLE

LNBF

VOLTAGE

+12VDC

POWER CABLE

REFLECTOR

SWITCH LOCATION

(SIDE OF BOX, SEE PAGE 3)

EL MOTOR

CONTROL BOX DETAIL

LNBF

RECEIVER

ELEVATION

AZIMUTH

(#1 represents Switch DOWN; #0 represents Switch up)

Sat. Rcvr. Mt. Option Switch Set Position

........................... 1 2 3 4 5 6 7 8

DIRECTV ...................... A ....... 0 .. 0 .. 0 .. 0 . 0 .. 0 .. 0 .. 1

(FACTORY PRESET)

DIRECTV ..................... B ....... 1 .. 0 .. 0 .. 0 . 0 .. 0 .. 0 .. 1

DISH NETWORK ................. A ....... 0 .. 0 .. 0 .. 1 . 0 .. 0 .. 1 .. 1

DISH NETWORK ................. B ......... 1 .. 0 .. 0 .. 1 . 0 .. 0 .. 1 .. 1

ExpressVu ................... A ....... 0 .. 1 .. 0 .. 1 . 1 .. 0 .. 1 .. 1

ExpressVu ................... B ....... 1 .. 1 .. 0 .. 1 . 1 .. 0 .. 1 .. 1

Vehicle

Front

Mount

Option A

Vehicle

Front

Mount

Option B

ELECTRONICS INTERIOR VIEW

GPS ANTENNA

CABLE

CENTER

LINE OF THE

VEHICLE



Installation

IMPORTANT! Do not install this system

in the rain, or under any wet conditions. Mois-

ture may affect electronics and void your

warranty!

1. For best performance and to reduce signal ac-

quisition time, park vehicle on a level surface; level

the RV.

2. Select a level spot on your roof for installation.

Using the chart,

determine the

minimum distances

to other equipment.

WARNING: Level the base front to back and

side to side. If base is not level the MV-4002 may

require more time to locate the correct satellite

or may not locate the correct satellite.

• Be sure no roof-mounted equipment is

blocking the satellite “line of sight”, Fig. 3

• You will need to decide where the wires will enter

the vehicle. A coax and a power wire (minimum 16

gauge) will need to be run into the vehicle.

WARNING: Many +12VDC sources can cause the unit

to fail. Select a filtered source, preferably a dedi-

cated line to the battery.

Install in DRY conditions only!

Installing unit on roof of vehicle —

Obstruction Ht. Unit Clearance

8” .......................................... 4”

10” ................................... 11.5”

12” ...................................... 19”

15” ...................................... 32”

3. Remove dome. Place dome in safe spot to avoid

damage. Place base on vehicle roof in the location

selected.

4. Attach each mounting foot to base by securing

with two 7/16” nylocks. See page 7 for foot locations.

5. After selecting location for unit (see number 2),

put the unit on the centerline of the vehicle.

REAR MOUNTING FOOT MUST BE PARALLEL

WITH THE CENTER LINE OF VEHICLE. See pg. 7.

6. Place the unit on the roof in its permanent loca-

tion and mark around the base bracket, Figure 4.

(Make sure the rear adjustable base foot is par-

allel with the center line of the vehicle. Refer

to page 3, Figure 1A ).

8. Put approved sealant in the areas marked

for the base feet. Place base feet on top of the

sealant and screw down with the (4) #10

screws (provided) for each foot.

9. After all base feet are secured to roof, put

sealant around edge of feet and over screws.

Replace base on screws and reinstall nut.

7. Clean roof area where the base feet will be at-

tached to the roof. Do not erase your marks!

FIGURE 4

FIGURE 3

OBSTRUCTION

UNIT BASE

FIGURE 5 BASE EXTERIOR

1. Decide the best location for the cables to enter the

vehicle, and the location of the switch and receiver

(see “Installing the switch and receiver”on page 10). Drill

a 1/2” hole in the roof, push wires inside. Make proper

connections.

You must have filtered +12 VDC power source.

2. Place cable-entry plate over hole and cables. Screw

in place. Seal plate and screw holes with approved seal-

ant (not included).

3. Depending on the length of the cable on the roof, you

may need to use cable clamps or wire ties (not pro-

vided) between the unit and your cable-entry plate.

Clamping the cable every 12”-16” should eliminate any

unnecessary cable movement, Figure 6.

Installation

CABLE-

ENTRY

CABLE

CLAMPS

FIGURE 4

Cable entry installation —

INSTALLING THE POWER SWITCH

1. Choose a location to install the MV-4002 power

ON/OFF switch. Remember when selecting a location

that you will need to run the +12VDC power cable from

the MV-4002 to the switch. Be sure the switch is in

the OFF position before continuing. See Figure 9

page 10.

Wall or panel mount: Drill 1-1/4” hole, pull wires

through wall or panel.

Surface mount: Determine location and direction of

box. Mount box and feed wire into one of the box open

ings. Select plate cover (brown or white provided) and

snap the rocker switch into the switch plate. Be sure

switch is off!

2. Connect the ground wire from the vehicle and the

BLACK ground wire from the MV-4002 together,

using large yellow spade connector.

3. Connect the YELLOW spade connector to

the silver spade on the switch.

4. Connect the RED wire from the MV unit to the

small RED spade connector.

5. Connect small RED spade connector to center

spade on switch.

6. Connect the +12 V power wire from the vehicle to

a small RED spade connector.

7. Connect small RED spade connect to isolated

spade on switch.

INSTALLING THE POWER SWITCH DIAGRAM

STEPS 2 & 3

TWO GROUND WIRES

1 FROM VEHICLE

1 BLACK WIRE FROM

SATELLITE DISH STEPS 4 & 5

RED POWER

WIRE FROM

DISH

STEPS 6 &7

+12 V FROM VEHICLE

ON/OFF ROCKER SWITCH

WITH LIGHT

(Shown in OFF position.)

FIGURE 5

Terminals on switch have to be bent to fit in surface

mount box.

INSTALLING THE DOME

Insert screw in holes on dome

rim. Be sure bolt is vertical;

not tilted to side. Tighten to

20 in-lb., or approximately

until washer is visible

around screw head.

CAUTION:

DO NOT

OVERTIGHTEN!!

QUADREX

SCREW WITH

RUBBER

WASHER

(USE #2

PHILLIPS)

10. The GPS antenna is pre-wired and has a 1 meter

cable running through one of the connectors.

Determine location for GPS antenna. It is recom-

mended you place the GPS antenna 3 feet from dome.

The recommended location for the GPS antenna is

based on having a level location and a clear view of the

sky for the best satellite signal acquisition. Do not se-

cure GPS antenna to roof at this time.

IMPORTANT! The GPS must be located minimum of 3

feet away from obstructions on roof of vehicle. Antenna

must have a clear view of the sky for proper op-

eration.

GPS installation —

Installation • Wiring

Initializing —

1. Be sure vehicle is in a location free of all obstruc-

tions and with a clear view of the southern sky.

2. DO NOT MOVE VEHICLE during the first

initialization. Power up unit, turn on receiver. FOR

THE FIRST TIME ONLY, the unit may take up to

10 minutes to initially find the satellite signal. The

GPS is also initializing at this time. After the GPS

initializes, the unit will begin searching for the

correct satellite. See page 4 for detail of operation.

3. If the GPS does not initialize at this time, turn

off the unit. You may need to move the GPS

antenna to a different location on your roof. After

you move the GPS, DO NOT SECURE TO ROOF.

4. TEST YOUR SYSTEM BEFORE SECURING

THE GPS ANTENNA. Make sure the

TV/receiver has found the correct satellite.

5. After the correct satellite has been found, secure

GPS antenna by removing adhesive backing

and securing to roof.

WIRING TWO RECEIVERS

SECONDARY

SATELLITE

PRIMARY RECEIVER

SATELLITE IN

INPUT

NOT USED

INPUT

OUT

SP-2052

SAT RECEIVER

D575p DEMULTIPLEXER

DEMULTIPLEXER

DC BLOCK

RECEIVER

Connecting two receivers—

Connecting first receiver:

1. Inside the vehicle, connect the coax cable from the

roof to the “IN” input on the splitter (SP-2052). Connect

a coax cable from one of the “OUT” ports or jack on the

splitter (SP-2052). Connect other end of this cable to

the “input” on the DC PASSIVE D575p demultiplexer.

2. The primary receiver is the one used most often.

This receiver will also control the satellite dish.

3. Connect a coax cable from the “satellite receiver”

output on the DC PASSIVE D575p demultiplexer. Con-

nect the other end of this cable to “Satellite IN”

on the primary receiver.

Connecting the second receiver:

4. Connect a coax cable from the other “OUT” output

on the splitter (SP-2052). Connect the other end of this

cable to the “input” on the DC BLOCK demultiplexer.

5. Connect a coax cable from the “receiver” output on the

DC BLOCK demultiplexer. Connect the other end of this

cable to “Satellite IN” on the secondary receiver.

6. This receiver will only view the satellite that the main

receiver is on.It will never toggle on it’s on.

MV-4002 Tracking System

Connecting one receiver

1. Mount the DC Passive D575p demultiplexer in the

same cabinet as your receiver.

2. Connect the coax cable from the roof to the “input” on

the DC Passive D575p demultiplexer. Connect a coax

cable from the “sat receiver” on the DC Passive

demultiplexer. Connect other end of this cable to “satel-

lite in” on receiver.

Connecting the receiver —

D575p

DEMULTIPLEXER

DC PASSIVE

SAT RECEIVER

WIRING ONE RECEIVER

SATELLITE IN

NOT USED

INPUT

Inhaltsverzeichnis

Andere Winegard Antenne Handbücher

Winegard

Winegard RAYZAR RV-RZ85 Bedienungsanleitung

Winegard

Winegard DuraSAT D4 CM2000T Bedienungsanleitung

Winegard

Winegard HD-7084P Bedienungsanleitung

Winegard

Winegard Carryout PM-2000 Bedienungsanleitung

Winegard

Winegard HD6055P Bedienungsanleitung

Winegard

Winegard Pathway X1 Bedienungsanleitung

Winegard

Winegard MT-4000 Bedienungsanleitung

Winegard

Winegard Movin' View MV3500A Bedienungsanleitung

Winegard

Winegard HD7698 Bedienungsanleitung

Winegard

Winegard 2-WAY SATELLITE INTERNET SYSTEM Bedienungsanleitung

Winegard

Winegard SK-7003 Mount Bedienungsanleitung

Winegard

Winegard RZ-7500 Bedienungsanleitung

Winegard

Winegard A3-2000 Betriebsanleitung

Winegard

Winegard HD7078P Bedienungsanleitung

Winegard

Winegard Carryout PM-2000 Bedienungsanleitung

Winegard

Winegard AIR 360+ Bedienungsanleitung

Winegard

Winegard HD7082P Bedienungsanleitung

Winegard

Winegard Movin' View MV-0022 Bedienungsanleitung

Winegard

Winegard RT8000T Bedienungsanleitung

Winegard

Winegard TRAV'LER DIRECTV SK-SWM3 Bedienungsanleitung

Winegard

Winegard RD-9146 Bedienungsanleitung

Winegard

Winegard SensarPro Bedienungsanleitung

Winegard

Winegard HD7210P Bedienungsanleitung

Winegard

Winegard TR-6100 Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

IWCS

IWCS iriBelt II Einrichtungshandbuch